Smartrise KEB Series Manual de instalación y operación
2
KEB Introduction
EQUIPMENT/SETTINGS VERIFICATION
Verify that the Job Specification parameter table on the drawings
“Sheet 1: Getting Started” matches the actual equipment.
Below is a sample table showing the important values that will
affect operation.
Scroll through the motor parameters and verify that they are set to the
motor nameplate values prior to performing the Motor Learn
procedure.
Sample: Sheet 1: - Getting Started
Motor
Volts
Motor
Amps
Motor
RPM
Motor
Poles
Motor
HP
Brake Volts
Pick/Hold
Encoder
PPR
Main Line
Volts
Motor
Frequency
3
CONTROLLER GROUNDING REQUIREMENTS
NOTE –For the controller to function properly it is very important to
provide proper building ground connections to the controller.
Examples of a proper building-to-controller ground connection is
to attach the ground cable to:
The street side of the incoming water main.
To a grounding rod that has been driven into the pit flooring.
The controller has a common ground bus terminal connection.
All grounds need to land at this common point including building,
motor, transformer, and filter grounds. This prevents ground loops,
and will limit the impedance between the grounds and noise will
be channeled back to building ground.
Providing a proper ground is mandatory and will improve the
performance of the controller.
4
WIRING –(Check off box when complete)
** Refer to the Appendix for the following connections **
Power –(Sheet 3: Machine Room connections)
Connect main line power to terminal block L1/L2/L3.
Connect the ground wire to the yellow/green terminal block
next to L1-L3.
Brake –(Sheet 5: Brakes)
Connect the main brake wiring to terminals K1 / K2 located
on the terminal block next to the M contactor.
Jump EB to the terminal listed in the Construction box located
on “Sheet 01 – Getting Started” and connect either the rope
gripper or shieve brake to EBR (if installed).
Motor / Encoder –(Sheet 4: Drive and Motor)
Connect motor leads to the M contactor at T1/T2/T3.
Connect the encoder cable wiring to the encoder card
mounted on the drive. The table below contains wiring
references for common encoders.
5
24VDC
connections to
SRU board IOs
120VAC
connections to
DIN Rail
terminals
Emergency
brake power
Temporary Run Stop Switch
Enable
CONSTRUCTION –(Sheet 1: Construction)
The following instructions are from the job drawings: “Sheet 1 –
Construction”. Refer to the job’s specific drawings for connections.
Construction Box (Sample)
24v DC connections
Install jumpers between M24 and the IOs listed on “Sheet 1:
Getting Started –Construction”.
Install jumpers between M24 any additional IO’s (if required):
* Pre-Transfer * Emergency Power
* Governor
IMPORTANT! REMOVE FACTORY WIRES ON INPUTS 521/522
oInstall the Run Bug Up/Down Switch to IO’s 521/522
Install the Run Bug Up/Down Enable switch to M24
120v AC connections
Install the temporary run switch between 120 and terminal
SF1 and 120 to THL/MHL/BHL terminals on the DIN rail.
Install a jumper between EB and the terminal listed on the
drawings on “Sheet 1: Getting Started – Construction”.
6
POWERING UP
(Check off box when complete)
Apply external power by closing the main disconnect.
Close the L1/L2 breaker, the M24, PS, BR and EBR breakers.
Verify that the LCD on the Smartrise board and the KEB Drive
come on.
FINAL SETUP
(Check off box when complete)
Toggle the Inspection/Normal switch to the “INSP” position.
Set BYPASS TERM LIMITS to YES:
oOn the Smartrise Machine Room controller board, press
the Left Arrow (ESC) button several times to get to the
MAIN SCREEN.
oPress the Right Arrow to go to MAIN MENU. Use the Up /
Down Arrow keys and move the asterix to SETUP and press
the enter key.
Green in Window
OFF
Red in Window
ON
Up = OFF
Down = ON
MAIN MENU
Status
Faults
*Setup
7
oUse the Up / Down Arrow keys and move the asterix to
MISC and press the enter key.
oBYPASS TERM LIMITS should be the first item listed. If it’s
not there use the Up / Down Arrow keys and move the
asterix to BYPASS TERM LIMITS and press the enter key.
oUse the Up / Down Arrow keys to change the word “NO”
to “YES”.
oUse the RIGHT Arrow key and move the asterix under the
word “SAVE” and press enter.
oHit the LEFT Arrow (ESC) button several times to get to the
MAIN SCREEN.
Verify the LCD displays “Construction”Mode on the MAIN
SCREEN.
SETUP
Local Outputs
Security
*Misc
MISC
*Bypass Term Limits
Emergency Power
Monitor BPS
BYPASS TERM LIMITS
NO
*
BYPASS TERM LIMITS
YES Save
*
8
KEB Motor Learn
NOTE: Smartrise programs the KEB drive with factory defaults to properly
communicate with the controller. After factory testing, customer motor data
(from customer’s EDF) is programmed into the drive to provide an easier “out of
box” installation.
Initial Start Up
The complete motor data must be learned with the automated learn function.
The Motor Learn function can be found under the Tune Parameters group from the
Programming menu (Home > Prog > Tune Parameters > LL01).
Begin the procedure by setting:
• Motor Tuning LL01 = Start
Follow the instructions on the LCD screen. The user is instructed to:
1. Disable the brake (turn off the BR and EBR breaker).
2. Set command to zero on the MR SRU board under MAIN MENU | SETUP
| SPEED AND SLOWDOWNS | INSPECTION SPEED –set to “0”.
3. On the controller press and hold inspection (speed + direction + enable
inputs) until completed.
The process should take 2-5 minutes and will emit a high pitched noise while the
drive measures various motor parameters.
If not performing the Encoder Synchronization, turn on BR and EBR
breakers and return the inspection speed to factory setting on the
controller.
SETUP OF THE MOTOR LEARN IS NOW COMPLETE!
9
KEB Encoder Learn
1. Encoder Synchronization
The Encoder Synchronization process will determine the correct A/B encoder
channel phasing and direction of rotation for Induction motors.
Begin the process by setting:
• LL07 - Encoder Synchronization to “Start”
Follow the directions on the keypad. The drive will run the elevator and swap
the phasing and direction of the A/B channels as needed.
Turn on the BR and EBR breakers and return the inspection speed to
factory setting on the controller.
SETUP OF THE ENCODER LEARN IS NOW COMPLETE!
10
OPERATION
(Check off box when complete)
Run the car and verify the following:
No Faults
Make sure the car is moving without triggering a fault either
on the Smartrise SRU or the drive. If the SRU board displays a
“Drive Fault” on the SRU, look at the drive to see what the
fault is.
oGo to “Troubleshooting –Drive Fault / Encoder Flt” for
corrective actions.
Proper Direction
Make sure the car is moving in the same direction as the
control switch on the Run Bug.
oGo to “Troubleshooting –Wrong Direction” for corrective
actions.
At Speed
Make sure that the car is moving at the proper inspection
speed (approx. 50 FPM).
oGo to “Troubleshooting –Car Moving Too Slow or Rough”
for corrective actions.
Under Control
Make sure that the car is moving under full control. The car
should stop when commanded from the Run Bug. Verify that
the car runs with no faults for 10 seconds or more.
oGo to “Troubleshooting –Brake Not Lifting” for corrective
actions.
Tabla de contenidos
Otros manuales de Accionamiento de CC de Smartrise
Smartrise
Smartrise Magnetek HPV900AF Manual de instalación y operación
Smartrise
Smartrise KEB-Induction Manual de instalación y operación
Smartrise
Smartrise C4 Manual de usuario
Smartrise
Smartrise C4 Manual de instalación y operación
Smartrise
Smartrise HPV900 Manual de instalación y operación
Smartrise
Smartrise HPV900-PM Manual de instalación y operación
Smartrise
Smartrise Magnetek L1000A Manual de instalación y operación
Smartrise
Smartrise KEB-PM Manual de instalación y operación
Smartrise
Smartrise DSD412 Manual de instalación y operación
Smartrise
Smartrise HPV900-INDUCTION Manual de instalación y operación
Manuales populares de Accionamiento de CC de otras marcas
Vincent Associates
Vincent Associates UNIBLITZ ED12DSS Manual de usuario
EKSMA OPTICS
EKSMA OPTICS DQ-100-4 Manual de lista de piezas
Chamberlain Garog
Chamberlain Garog D Series Manual de usuario
Parker
Parker PDS Series Manual de usuario
Festo
Festo DGC G Series Guía de configuración
Binks
Binks QS-5012-1-CE Manual de usuario
ABB
ABB RSYC-01 Manual de usuario
Rockwell Automation
Rockwell Automation PowerFlex 700S Manual del propietario
WEG
WEG DeviceNet CFW500 Manual de usuario
Siemens
Siemens SINAMICS G Hoja de datos
Siemens
Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Instrucciones de funcionamiento
SOMFY
SOMFY JR RU 30 Manual de usuario