SmartPro Reader I Manual del propietario

GENERATION AHEAD TECHNOLOGY

Place the gemstone on the metal stone tray and hold it with one hand while holding the tester with

the other hand (Fig.2.2).

CONTENTS

I. Introduction

II. About the SmartPro Reader I

III. IMPORTANT NOTICE

1. GETTING STARTED

2. PERFORMING A TEST

3. READING TEST RESULTS

4. TAKING CARE

For testing loose gemstones

Fig. 2.2

For mounted jewelry or gemstones

2. PERFORMING A TEST

Hold the jewelry or gemstone with one hand and the tester with other hand (Fig.2.1). For proper

operation of the tester, the thumb and index finger must always be placed on the metal-plated

serrated part located on both sides of the tester at all times. Care should be taken when testing

mounted jewelry. User must ensure that the stones are securely mounted before conducting a test

as gap between stone an setting might lead to inaccurate reading.

Place the tip of the probe pen against the gemstone. Apply minimal pressure to fully depress the

tip into the probe pen for correct reading. This is to provide a steady and constant contact made

between the probe tip and the gemstone.

II. About the SmartPro Reader I

The SmartPro Reader I precisely measures the thermal electrical conductivity of the specific

gemstone and determine if it is a diamond, moissanite or simulant. Via a customized

micro-controller. The results will be display within second.

The Smartpro Reader I has been subjected to thorough and extensive laboratory tests, and will

generally give a clear and reliable reading of the gemstone being tested under proper use.

However, you are advice to conduct further supporting tests.

Included in your package:

a. SmartPro Reader I

b. User manual book

c. Warranty card

d. Protective carry case

e. Probe tip oxidation sheet

f. Neck strap

g. Metal stone tray

Gently rub the table of gemstone against the tissue / jewelry cloth and place the gemstone on the

center of the test pad (Fig.1.9).

Fig. 1.9

Place the gemstone on the metal stone tray and hold it with one hand while holding the tester with

the other hand (Fig.2.2).

CONTENTS

I. Introduction

II. About the SmartPro Reader I

III. IMPORTANT NOTICE

1. GETTING STARTED

2. PERFORMING A TEST

3. READING TEST RESULTS

4. TAKING CARE

For testing loose gemstones

Fig. 2.2

For mounted jewelry or gemstones

2. PERFORMING A TEST

Hold the jewelry or gemstone with one hand and the tester with other hand (Fig.2.1). For proper

operation of the tester, the thumb and index finger must always be placed on the metal-plated

serrated part located on both sides of the tester at all times. Care should be taken when testing

mounted jewelry. User must ensure that the stones are securely mounted before conducting a test

as gap between stone an setting might lead to inaccurate reading.

Place the tip of the probe pen against the gemstone. Apply minimal pressure to fully depress the

tip into the probe pen for correct reading. This is to provide a steady and constant contact made

between the probe tip and the gemstone.

II. About the SmartPro Reader I

The SmartPro Reader I precisely measures the thermal electrical conductivity of the specific

gemstone and determine if it is a diamond, moissanite or simulant. Via a customized

micro-controller. The results will be display within second.

The Smartpro Reader I has been subjected to thorough and extensive laboratory tests, and will

generally give a clear and reliable reading of the gemstone being tested under proper use.

However, you are advice to conduct further supporting tests.

Included in your package:

a. SmartPro Reader I

b. User manual book

c. Warranty card

d. Protective carry case

e. Probe tip oxidation sheet

f. Neck strap

g. Metal stone tray

Gently rub the table of gemstone against the tissue / jewelry cloth and place the gemstone on the

center of the test pad (Fig.1.9).

Fig. 1.9

Place the gemstone on the metal stone tray and hold it with one hand while holding the tester with

the other hand (Fig.2.2).

CONTENTS

I. Introduction

II. About the SmartPro Reader I

III. IMPORTANT NOTICE

1. GETTING STARTED

2. PERFORMING A TEST

3. READING TEST RESULTS

4. TAKING CARE

For testing loose gemstones

Fig. 2.2

For mounted jewelry or gemstones

2. PERFORMING A TEST

Hold the jewelry or gemstone with one hand and the tester with other hand (Fig.2.1). For proper

operation of the tester, the thumb and index finger must always be placed on the metal-plated

serrated part located on both sides of the tester at all times. Care should be taken when testing

mounted jewelry. User must ensure that the stones are securely mounted before conducting a test

as gap between stone an setting might lead to inaccurate reading.

Place the tip of the probe pen against the gemstone. Apply minimal pressure to fully depress the

tip into the probe pen for correct reading. This is to provide a steady and constant contact made

between the probe tip and the gemstone.

II. About the SmartPro Reader I

The SmartPro Reader I precisely measures the thermal electrical conductivity of the specific

gemstone and determine if it is a diamond, moissanite or simulant. Via a customized

micro-controller. The results will be display within second.

The Smartpro Reader I has been subjected to thorough and extensive laboratory tests, and will

generally give a clear and reliable reading of the gemstone being tested under proper use.

However, you are advice to conduct further supporting tests.

Included in your package:

a. SmartPro Reader I

b. User manual book

c. Warranty card

d. Protective carry case

e. Probe tip oxidation sheet

f. Neck strap

g. Metal stone tray

Gently rub the table of gemstone against the tissue / jewelry cloth and place the gemstone on the

center of the test pad (Fig.1.9).

Fig. 1.9

I. Introduction

Congratulations on your new SmartPro Reader I the newly 3 in 1 impeccable tester that can even-

tually ascertain your stone between Diamond, Moissanite and Simulant, based on their thermal and

Electrical conductivity with its readable LCD display for easy reading measurements.

In creating SmartPro Reader I, professional engineers selected every material and element to have

this fine-looking and effective tester that helps in the identification of the diamond moissanite and

simulants. This device provides fairly consistent and reliable test results.

Fig. 2.1

While in this preparation mode, a “SmartPro” will blink continuously on the LCD. The “SmarPro”

will stop blinking when it is show “READY” on the LCD and now ready to be used (Fig. 1.5). The

tester will shut down automatically after 2 minutes of inactivity.

a. Retractable thermoelectric probe tip that ensures constant pressure between probe tip and

gemstone.

b. Industry’s thinnest probe tip (0.48mm) for testing gemstones as small as 1.0mm (0.01ct)

c. Metal alert buzzer to ensure that probe tip is in contact with gemstone during testing.

d. No waiting time between tests.

e. Ergonomic design for better handling during testing.

f. LCD display.

g. International voltage compatibility.

h. Low battery indicator.

i. Automatic power off.

j. Help in the identification of the diamond and moissanite with a single instrument.

k. Provide fairly consistent and reliable test results under proper use.

The SmartPro Reader I features the following:

Prepare clean tissue / jewelry cloth. Carefully retrieve the gemstone with tweezers and place the

gemstone face down the table (Fig.1.8).

Cleaning your gemstone prior to testing

Fig. 1.8

Battery information

Do not leave worn out batteries in the battery compartment as the batteries may corrode, leak, and

damage the tester. Batteries should be removed when the tester is expected to be stored for an

extended period of time.

To prevent inaccurate readings, replace with new batteries as soon as the low battery indicator will

show. A test should not be performed when the battery power is low or weak.

All testers have been calibrated during the manufacturing process and no further adjustment or

user intervention to the tester is required.

Self-calibration should not be attempted. To minimize any risk associated, user should contact

SmartPro at customercare@smartproinstrument.com or its service center for assistance. In the

event that users require the manufacturer to re-calibrate the unit, the users will bear the associated

to/from freight cost for the shipping of unit to the service center.

Calibration

Place the gemstone on the metal stone tray and hold it with one hand while holding the tester with

the other hand (Fig.2.2).

CONTENTS

I. Introduction

II. About the SmartPro Reader I

III. IMPORTANT NOTICE

1. GETTING STARTED

2. PERFORMING A TEST

3. READING TEST RESULTS

4. TAKING CARE

For testing loose gemstones

Fig. 2.2

For mounted jewelry or gemstones

2. PERFORMING A TEST

Hold the jewelry or gemstone with one hand and the tester with other hand (Fig.2.1). For proper

operation of the tester, the thumb and index finger must always be placed on the metal-plated

serrated part located on both sides of the tester at all times. Care should be taken when testing

mounted jewelry. User must ensure that the stones are securely mounted before conducting a test

as gap between stone an setting might lead to inaccurate reading.

Place the tip of the probe pen against the gemstone. Apply minimal pressure to fully depress the

tip into the probe pen for correct reading. This is to provide a steady and constant contact made

between the probe tip and the gemstone.

II. About the SmartPro Reader I

The SmartPro Reader I precisely measures the thermal electrical conductivity of the specific

gemstone and determine if it is a diamond, moissanite or simulant. Via a customized

micro-controller. The results will be display within second.

The Smartpro Reader I has been subjected to thorough and extensive laboratory tests, and will

generally give a clear and reliable reading of the gemstone being tested under proper use.

However, you are advice to conduct further supporting tests.

Included in your package:

a. SmartPro Reader I

b. User manual book

c. Warranty card

d. Protective carry case

e. Probe tip oxidation sheet

f. Neck strap

g. Metal stone tray

Gently rub the table of gemstone against the tissue / jewelry cloth and place the gemstone on the

center of the test pad (Fig.1.9).

Fig. 1.9

I. Introduction

Congratulations on your new SmartPro Reader I the newly 3 in 1 impeccable tester that can even-

tually ascertain your stone between Diamond, Moissanite and Simulant, based on their thermal and

Electrical conductivity with its readable LCD display for easy reading measurements.

In creating SmartPro Reader I, professional engineers selected every material and element to have

this fine-looking and effective tester that helps in the identification of the diamond moissanite and

simulants. This device provides fairly consistent and reliable test results.

Fig. 2.1

While in this preparation mode, a “SmartPro” will blink continuously on the LCD. The “SmarPro”

will stop blinking when it is show “READY” on the LCD and now ready to be used (Fig. 1.5). The

tester will shut down automatically after 2 minutes of inactivity.

a. Retractable thermoelectric probe tip that ensures constant pressure between probe tip and

gemstone.

b. Industry’s thinnest probe tip (0.48mm) for testing gemstones as small as 1.0mm (0.01ct)

c. Metal alert buzzer to ensure that probe tip is in contact with gemstone during testing.

d. No waiting time between tests.

e. Ergonomic design for better handling during testing.

f. LCD display.

g. International voltage compatibility.

h. Low battery indicator.

i. Automatic power off.

j. Help in the identification of the diamond and moissanite with a single instrument.

k. Provide fairly consistent and reliable test results under proper use.

The SmartPro Reader I features the following:

Prepare clean tissue / jewelry cloth. Carefully retrieve the gemstone with tweezers and place the

gemstone face down the table (Fig.1.8).

Cleaning your gemstone prior to testing

Fig. 1.8

Battery information

Do not leave worn out batteries in the battery compartment as the batteries may corrode, leak, and

damage the tester. Batteries should be removed when the tester is expected to be stored for an

extended period of time.

To prevent inaccurate readings, replace with new batteries as soon as the low battery indicator will

show. A test should not be performed when the battery power is low or weak.

All testers have been calibrated during the manufacturing process and no further adjustment or

user intervention to the tester is required.

Self-calibration should not be attempted. To minimize any risk associated, user should contact

SmartPro at customercare@smartproinstrument.com or its service center for assistance. In the

event that users require the manufacturer to re-calibrate the unit, the users will bear the associated

to/from freight cost for the shipping of unit to the service center.

Calibration

Place the gemstone on the metal stone tray and hold it with one hand while holding the tester with

the other hand (Fig.2.2).

CONTENTS

I. Introduction

II. About the SmartPro Reader I

III. IMPORTANT NOTICE

1. GETTING STARTED

2. PERFORMING A TEST

3. READING TEST RESULTS

4. TAKING CARE

For testing loose gemstones

Fig. 2.2

For mounted jewelry or gemstones

2. PERFORMING A TEST

Hold the jewelry or gemstone with one hand and the tester with other hand (Fig.2.1). For proper

operation of the tester, the thumb and index finger must always be placed on the metal-plated

serrated part located on both sides of the tester at all times. Care should be taken when testing

mounted jewelry. User must ensure that the stones are securely mounted before conducting a test

as gap between stone an setting might lead to inaccurate reading.

Place the tip of the probe pen against the gemstone. Apply minimal pressure to fully depress the

tip into the probe pen for correct reading. This is to provide a steady and constant contact made

between the probe tip and the gemstone.

II. About the SmartPro Reader I

The SmartPro Reader I precisely measures the thermal electrical conductivity of the specific

gemstone and determine if it is a diamond, moissanite or simulant. Via a customized

micro-controller. The results will be display within second.

The Smartpro Reader I has been subjected to thorough and extensive laboratory tests, and will

generally give a clear and reliable reading of the gemstone being tested under proper use.

However, you are advice to conduct further supporting tests.

Included in your package:

a. SmartPro Reader I

b. User manual book

c. Warranty card

d. Protective carry case

e. Probe tip oxidation sheet

f. Neck strap

g. Metal stone tray

Gently rub the table of gemstone against the tissue / jewelry cloth and place the gemstone on the

center of the test pad (Fig.1.9).

Fig. 1.9

I. Introduction

Congratulations on your new SmartPro Reader I the newly 3 in 1 impeccable tester that can even-

tually ascertain your stone between Diamond, Moissanite and Simulant, based on their thermal and

Electrical conductivity with its readable LCD display for easy reading measurements.

In creating SmartPro Reader I, professional engineers selected every material and element to have

this fine-looking and effective tester that helps in the identification of the diamond moissanite and

simulants. This device provides fairly consistent and reliable test results.

Fig. 2.1

While in this preparation mode, a “SmartPro” will blink continuously on the LCD. The “SmarPro”

will stop blinking when it is show “READY” on the LCD and now ready to be used (Fig. 1.5). The

tester will shut down automatically after 2 minutes of inactivity.

a. Retractable thermoelectric probe tip that ensures constant pressure between probe tip and

gemstone.

b. Industry’s thinnest probe tip (0.48mm) for testing gemstones as small as 1.0mm (0.01ct)

c. Metal alert buzzer to ensure that probe tip is in contact with gemstone during testing.

d. No waiting time between tests.

e. Ergonomic design for better handling during testing.

f. LCD display.

g. International voltage compatibility.

h. Low battery indicator.

i. Automatic power off.

j. Help in the identification of the diamond and moissanite with a single instrument.

k. Provide fairly consistent and reliable test results under proper use.

The SmartPro Reader I features the following:

Prepare clean tissue / jewelry cloth. Carefully retrieve the gemstone with tweezers and place the

gemstone face down the table (Fig.1.8).

Cleaning your gemstone prior to testing

Fig. 1.8

Battery information

Do not leave worn out batteries in the battery compartment as the batteries may corrode, leak, and

damage the tester. Batteries should be removed when the tester is expected to be stored for an

extended period of time.

To prevent inaccurate readings, replace with new batteries as soon as the low battery indicator will

show. A test should not be performed when the battery power is low or weak.

All testers have been calibrated during the manufacturing process and no further adjustment or

user intervention to the tester is required.

Self-calibration should not be attempted. To minimize any risk associated, user should contact

SmartPro at customercare@smartproinstrument.com or its service center for assistance. In the

event that users require the manufacturer to re-calibrate the unit, the users will bear the associated

to/from freight cost for the shipping of unit to the service center.

Calibration

Place the gemstone on the metal stone tray and hold it with one hand while holding the tester with

the other hand (Fig.2.2).

CONTENTS

I. Introduction

II. About the SmartPro Reader I

III. IMPORTANT NOTICE

1. GETTING STARTED

2. PERFORMING A TEST

3. READING TEST RESULTS

4. TAKING CARE

For testing loose gemstones

Fig. 2.2

For mounted jewelry or gemstones

2. PERFORMING A TEST

Hold the jewelry or gemstone with one hand and the tester with other hand (Fig.2.1). For proper

operation of the tester, the thumb and index finger must always be placed on the metal-plated

serrated part located on both sides of the tester at all times. Care should be taken when testing

mounted jewelry. User must ensure that the stones are securely mounted before conducting a test

as gap between stone an setting might lead to inaccurate reading.

Place the tip of the probe pen against the gemstone. Apply minimal pressure to fully depress the

tip into the probe pen for correct reading. This is to provide a steady and constant contact made

between the probe tip and the gemstone.

II. About the SmartPro Reader I

The SmartPro Reader I precisely measures the thermal electrical conductivity of the specific

gemstone and determine if it is a diamond, moissanite or simulant. Via a customized

micro-controller. The results will be display within second.

The Smartpro Reader I has been subjected to thorough and extensive laboratory tests, and will

generally give a clear and reliable reading of the gemstone being tested under proper use.

However, you are advice to conduct further supporting tests.

Included in your package:

a. SmartPro Reader I

b. User manual book

c. Warranty card

d. Protective carry case

e. Probe tip oxidation sheet

f. Neck strap

g. Metal stone tray

Gently rub the table of gemstone against the tissue / jewelry cloth and place the gemstone on the

center of the test pad (Fig.1.9).

Fig. 1.9

I. Introduction

Congratulations on your new SmartPro Reader I the newly 3 in 1 impeccable tester that can even-

tually ascertain your stone between Diamond, Moissanite and Simulant, based on their thermal and

Electrical conductivity with its readable LCD display for easy reading measurements.

In creating SmartPro Reader I, professional engineers selected every material and element to have

this fine-looking and effective tester that helps in the identification of the diamond moissanite and

simulants. This device provides fairly consistent and reliable test results.

Fig. 2.1

While in this preparation mode, a “SmartPro” will blink continuously on the LCD. The “SmarPro”

will stop blinking when it is show “READY” on the LCD and now ready to be used (Fig. 1.5). The

tester will shut down automatically after 2 minutes of inactivity.

a. Retractable thermoelectric probe tip that ensures constant pressure between probe tip and

gemstone.

b. Industry’s thinnest probe tip (0.48mm) for testing gemstones as small as 1.0mm (0.01ct)

c. Metal alert buzzer to ensure that probe tip is in contact with gemstone during testing.

d. No waiting time between tests.

e. Ergonomic design for better handling during testing.

f. LCD display.

g. International voltage compatibility.

h. Low battery indicator.

i. Automatic power off.

j. Help in the identification of the diamond and moissanite with a single instrument.

k. Provide fairly consistent and reliable test results under proper use.

The SmartPro Reader I features the following:

Prepare clean tissue / jewelry cloth. Carefully retrieve the gemstone with tweezers and place the

gemstone face down the table (Fig.1.8).

Cleaning your gemstone prior to testing

Fig. 1.8

Battery information

Do not leave worn out batteries in the battery compartment as the batteries may corrode, leak, and

damage the tester. Batteries should be removed when the tester is expected to be stored for an

extended period of time.

To prevent inaccurate readings, replace with new batteries as soon as the low battery indicator will

show. A test should not be performed when the battery power is low or weak.

All testers have been calibrated during the manufacturing process and no further adjustment or

user intervention to the tester is required.

Self-calibration should not be attempted. To minimize any risk associated, user should contact

SmartPro at customercare@smartproinstrument.com or its service center for assistance. In the

event that users require the manufacturer to re-calibrate the unit, the users will bear the associated

to/from freight cost for the shipping of unit to the service center.

Calibration

I. Introduction

Congratulations on your new SmartPro Reader I the newly 3 in 1 impeccable tester that can even-

tually ascertain your stone between Diamond, Moissanite and Simulant, based on their thermal and

Electrical conductivity with its readable LCD display for easy reading measurements.

In creating SmartPro Reader I, professional engineers selected every material and element to have

this fine-looking and effective tester that helps in the identification of the diamond moissanite and

simulants. This device provides fairly consistent and reliable test results.

Fig. 2.1

While in this preparation mode, a “SmartPro” will blink continuously on the LCD. The “SmarPro”

will stop blinking when it is show “READY” on the LCD and now ready to be used (Fig. 1.5). The

tester will shut down automatically after 2 minutes of inactivity.

a. Retractable thermoelectric probe tip that ensures constant pressure between probe tip and

gemstone.

b. Industry’s thinnest probe tip (0.48mm) for testing gemstones as small as 1.0mm (0.01ct)

c. Metal alert buzzer to ensure that probe tip is in contact with gemstone during testing.

d. No waiting time between tests.

e. Ergonomic design for better handling during testing.

f. LCD display.

g. International voltage compatibility.

h. Low battery indicator.

i. Automatic power off.

j. Help in the identification of the diamond and moissanite with a single instrument.

k. Provide fairly consistent and reliable test results under proper use.

The SmartPro Reader I features the following:

Prepare clean tissue / jewelry cloth. Carefully retrieve the gemstone with tweezers and place the

gemstone face down the table (Fig.1.8).

Cleaning your gemstone prior to testing

Fig. 1.8

Battery information

Do not leave worn out batteries in the battery compartment as the batteries may corrode, leak, and

damage the tester. Batteries should be removed when the tester is expected to be stored for an

extended period of time.

To prevent inaccurate readings, replace with new batteries as soon as the low battery indicator will

show. A test should not be performed when the battery power is low or weak.

All testers have been calibrated during the manufacturing process and no further adjustment or

user intervention to the tester is required.

Self-calibration should not be attempted. To minimize any risk associated, user should contact

SmartPro at customercare@smartproinstrument.com or its service center for assistance. In the

event that users require the manufacturer to re-calibrate the unit, the users will bear the associated

to/from freight cost for the shipping of unit to the service center.

Calibration

2025

Fig. 1.2

Composition

1. Retractable Probe Tip

2. “Ready” Indicator LED

3. LCD Display

4. Battery Compartment

5. Neck Strap Attachment

6. Adaptor Inlet

7. ON/OFF Switch

8. Ergonomic Grip

9. Probe Protective Cap

f. Do not drop, knock, or shake the tester. Rough handling can break internal circuit boards and

fine mechanics.

g. Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the tester.

h. Do not paint the tester. Paint can clog the moving parts and prevent proper operation.

If the tester is not working properly, kindly contact our customer service at

[email protected]

SmartPro Instrument co.,ltd

249/40, Moo 9, J.S.P. Building

Bangbon 1 Rd., Bangbon

Bangkok 10150 Thailand

+66 (0) 2 899 2956-7

Attn: Customer Service Executive

If batteries are used (3 x AAA batteries), take note of the positive (+) and negative (-) directions of

the batteries when inserting the batteries into the tester (Fig. 1.2). The use of alkaline batteries is

preferred, as it should generally give approximately two and a half hours of continuous operation,

while the use of ordinary batteries will give a shorter working life.

While in this preparation mode, a “SmartPro” will blink continuously on the LCD. The “SmarPro”

will stop blinking when it is show “READY” on the LCD and now ready to be used (Fig. 1.5). The

tester will shut down automatically after 2 minutes of inactivity.

Fig. 1.5

The recommended testing temperature is 18oC - 27oC or 65oF - 80oF Please allow the gemstone or

jewelry piece to adjust to room temperature prior to testing. Exposure and/or operation of the tester

outside the room temperature would affect the result and performance of tester.

The probe tip must be placed at the right angle or perpendicular to the facet of gemstone for an

accurate reading.

Tests should be conducted on the table of the gemstone. In the event of any doubt, kindly test on

the girdle of the gemstones instead.

To achieve optimum accuracy for tests involving very small, it is important to allow the gemstone

to cool down before subsequent tests.

Prepare clean tissue / jewelry cloth. Carefully retrieve the gemstone with tweezers and place the

gemstone face down the table (Fig.1.8).

Fig. 1.6

I. Introduction

Congratulations on your new SmartPro Reader I the newly 3 in 1 impeccable tester that can even-

tually ascertain your stone between Diamond, Moissanite and Simulant, based on their thermal and

Electrical conductivity with its readable LCD display for easy reading measurements.

In creating SmartPro Reader I, professional engineers selected every material and element to have

this fine-looking and effective tester that helps in the identification of the diamond moissanite and

simulants. This device provides fairly consistent and reliable test results.

Fig. 2.1

While in this preparation mode, a “SmartPro” will blink continuously on the LCD. The “SmarPro”

will stop blinking when it is show “READY” on the LCD and now ready to be used (Fig. 1.5). The

tester will shut down automatically after 2 minutes of inactivity.

a. Retractable thermoelectric probe tip that ensures constant pressure between probe tip and

gemstone.

b. Industry’s thinnest probe tip (0.48mm) for testing gemstones as small as 1.0mm (0.01ct)

c. Metal alert buzzer to ensure that probe tip is in contact with gemstone during testing.

d. No waiting time between tests.

e. Ergonomic design for better handling during testing.

f. LCD display.

g. International voltage compatibility.

h. Low battery indicator.

i. Automatic power off.

j. Help in the identification of the diamond and moissanite with a single instrument.

k. Provide fairly consistent and reliable test results under proper use.

The SmartPro Reader I features the following:

Prepare clean tissue / jewelry cloth. Carefully retrieve the gemstone with tweezers and place the

gemstone face down the table (Fig.1.8).

Cleaning your gemstone prior to testing

Fig. 1.8

Battery information

Do not leave worn out batteries in the battery compartment as the batteries may corrode, leak, and

damage the tester. Batteries should be removed when the tester is expected to be stored for an

extended period of time.

To prevent inaccurate readings, replace with new batteries as soon as the low battery indicator will

show. A test should not be performed when the battery power is low or weak.

All testers have been calibrated during the manufacturing process and no further adjustment or

user intervention to the tester is required.

Self-calibration should not be attempted. To minimize any risk associated, user should contact

SmartPro at customercare@smartproinstrument.com or its service center for assistance. In the

event that users require the manufacturer to re-calibrate the unit, the users will bear the associated

to/from freight cost for the shipping of unit to the service center.

Calibration

2025

Fig. 1.2

Composition

1. Retractable Probe Tip

2. “Ready” Indicator LED

3. LCD Display

4. Battery Compartment

5. Neck Strap Attachment

6. Adaptor Inlet

7. ON/OFF Switch

8. Ergonomic Grip

9. Probe Protective Cap

f. Do not drop, knock, or shake the tester. Rough handling can break internal circuit boards and

fine mechanics.

g. Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the tester.

h. Do not paint the tester. Paint can clog the moving parts and prevent proper operation.

If the tester is not working properly, kindly contact our customer service at

[email protected]

SmartPro Instrument co.,ltd

249/40, Moo 9, J.S.P. Building

Bangbon 1 Rd., Bangbon

Bangkok 10150 Thailand

+66 (0) 2 899 2956-7

Attn: Customer Service Executive

If batteries are used (3 x AAA batteries), take note of the positive (+) and negative (-) directions of

the batteries when inserting the batteries into the tester (Fig. 1.2). The use of alkaline batteries is

preferred, as it should generally give approximately two and a half hours of continuous operation,

while the use of ordinary batteries will give a shorter working life.

While in this preparation mode, a “SmartPro” will blink continuously on the LCD. The “SmarPro”

will stop blinking when it is show “READY” on the LCD and now ready to be used (Fig. 1.5). The

tester will shut down automatically after 2 minutes of inactivity.

Fig. 1.5

The recommended testing temperature is 18oC - 27oC or 65oF - 80oF Please allow the gemstone or

jewelry piece to adjust to room temperature prior to testing. Exposure and/or operation of the tester

outside the room temperature would affect the result and performance of tester.

The probe tip must be placed at the right angle or perpendicular to the facet of gemstone for an

accurate reading.

Tests should be conducted on the table of the gemstone. In the event of any doubt, kindly test on

the girdle of the gemstones instead.

To achieve optimum accuracy for tests involving very small, it is important to allow the gemstone

to cool down before subsequent tests.

Prepare clean tissue / jewelry cloth. Carefully retrieve the gemstone with tweezers and place the

gemstone face down the table (Fig.1.8).

Fig. 1.6

2025

Fig. 1.2

Composition

1. Retractable Probe Tip

2. “Ready” Indicator LED

3. LCD Display

4. Battery Compartment

5. Neck Strap Attachment

6. Adaptor Inlet

7. ON/OFF Switch

8. Ergonomic Grip

9. Probe Protective Cap

f. Do not drop, knock, or shake the tester. Rough handling can break internal circuit boards and

fine mechanics.

g. Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the tester.

h. Do not paint the tester. Paint can clog the moving parts and prevent proper operation.

If the tester is not working properly, kindly contact our customer service at

[email protected]

SmartPro Instrument co.,ltd

249/40, Moo 9, J.S.P. Building

Bangbon 1 Rd., Bangbon

Bangkok 10150 Thailand

+66 (0) 2 899 2956-7

Attn: Customer Service Executive

If batteries are used (3 x AAA batteries), take note of the positive (+) and negative (-) directions of

the batteries when inserting the batteries into the tester (Fig. 1.2). The use of alkaline batteries is

preferred, as it should generally give approximately two and a half hours of continuous operation,

while the use of ordinary batteries will give a shorter working life.

While in this preparation mode, a “SmartPro” will blink continuously on the LCD. The “SmarPro”

will stop blinking when it is show “READY” on the LCD and now ready to be used (Fig. 1.5). The

tester will shut down automatically after 2 minutes of inactivity.

Fig. 1.5

The recommended testing temperature is 18oC - 27oC or 65oF - 80oF Please allow the gemstone or

jewelry piece to adjust to room temperature prior to testing. Exposure and/or operation of the tester

outside the room temperature would affect the result and performance of tester.

The probe tip must be placed at the right angle or perpendicular to the facet of gemstone for an

accurate reading.

Tests should be conducted on the table of the gemstone. In the event of any doubt, kindly test on

the girdle of the gemstones instead.

To achieve optimum accuracy for tests involving very small, it is important to allow the gemstone

to cool down before subsequent tests.

Prepare clean tissue / jewelry cloth. Carefully retrieve the gemstone with tweezers and place the

gemstone face down the table (Fig.1.8).

Fig. 1.6

1. GETTING STARTED

Powering up

Turning on

This tester can be power by either the use of an AC adaptor (optional item sold separately) or

through the use of batteries. If AC adaptor is used, connect one end of the AC adaptor to the

tester (Fig. 1.1) and the other end directly into an electrical outlet. Please ensure that only the

adapter supplied by SmartPro is used.

Remove the protective cover from the probe tip (Fig. 1.3).

a. Keep the tester dry. Precipitation and all types of liquids or moisture can contain minerals that

will corrode electronic circuits. If your tester does get wet, remove the batteries, and allow the

tester to dry completely before replacing it.

b. Do not use, store or expose the tester in dusty and dirty areas. It’s moving part and electronic

components can be damage.

c. Do not use, store or expose the tester in hot areas. High temperatures can damage or shorten

the life of the tester, damage batteries, and warp or melt certain plastics.

d. Do not use, store or expose the tester in cold areas. When the tester returns to its normal tem-

perature, moisture can form inside the device and damage electronic circuit boards.

e. Do not attempt to open the tester other than as instructed in user manual book.

III. IMPORTANT NOTICE

Fig. 1.1

Fig. 1.3

Press the [ON/OFF] button located at the back of the tester (Fig. 1.4) and wait for about 20 sec-

onds to warm up the instrument.

Fig. 1.4

Cleaning the probe tip

Please note that if the tester is being used for the first time, or if the tester has not been used for

a week, it is advisable to clean the probe tip using an oxidation removal sheet to attain consistent

and accurate reading.

b. Hold the probe pen with pen tip forming the right angle (90 degree) with an oxidation removal.

Gently move in a circular motion without retracting the tip (Fig. 1.6).

a. Ensure the unit is switched off.

c. Repeat the same motion several times. The cleaning process is completed and tester is now

ready for use.

The gemstone should be clean and dry before testing. However, elaborate cleaning procedures

are not normally necessary (Fig. 1.7).

Recommended testing conditions

Fig. 1.7

Tabla de contenidos

Otros manuales de Equipo de prueba de SmartPro

SmartPro

SmartPro Optimum-1 Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario