Smart Witness KP1S Manual de usuario

www.smartwitness.com

SmartWitness KP1S

Installation Guide

v.1.2

WARNING: SmartWitness installations should be performed by a qualified individual or

installation professional only. Working with a vehicle's power system can be dangerous to

both you and your vehicle. This installation is intended only to be a guide since vehicle

designs and power/input sources can vary significantly from vehicle to vehicle.

If you need to schedule a professional installation service in the USA for your SmartWitness

device(s), please visit http://smartwitness.com/scheduleinstall and submit the online form.

www.smartwitness.com

1. Overview:

The SmartWitness KP1S is the world’s most advanced incident camera with powerful 3G

or WiFi video transmission, built-in GPS tracking and drive data. Developed to provide

evidence of events leading up to and during a road traffic accident, the KP1 provides

instant notifications and videos of incidents in less than a minute.

KP1S features a 720p wide angle HD camera, 3-Axis G-Sensor, Microphone, SD storage,

integrated GPS receiver, USB input (for 3G or WiFi modem), permanent power cable with

vehicle input triggers, and a tamper-resistant design.

Benefits:

The KP1S features a 720p HD wide angle (170°) lens to provide a comprehensive view

of any road event. The KP1S will record exactly what happened before, during and

after an incident. It does this by recording the following information: Drivers view of

the road, Vehicle Location, Impact Force of Accident, Audio, and Driving Style (speed,

acceleration, braking, and steering).

This evidence can protect a driver from many of the issues faced on the roads

today: Insurance fraud, Staged Accidents, False/Exaggerated Whiplash Claims,

Conflicting Reports of Actual Events, Driving Offence Allegations (speeding, traffic

signal violations, swerving, etc.).

When a 3G SIM card is used with KP1S, video, images, and driving data is transmitted

in real-time via a cellular network. Customers can use the KP1S to transmit safety-

critical video directly to a server (SmartWitness server software required), or integrate

with Telematics Software (Please contact us for a list of compatible telematics

software). The KP1S can also be used as a stand-alone system utilizing only the SD

cards to review video and data with SmartWitness’ free PC analysis software.

For more info on KP1S, please visit: smartwitness.com/3G-Dash-Cameras/KP1S

For literature downloads or support, please visit: support.smartwitness.com

www.smartwitness.com

Package Contents:

*Depending on the order, the secondary camera, 3G Modem, and SD card may or may not be included.

**SD Cards, Secondary camera, Power Adaptor, and 3G modems may be in a separate package from the KP1S

(common in large, bulk orders).

2. KP1S Structure:

KP1S Recorder with

locking cover

Power Adaptor

(model # INT1S)

3M Windshield

Adhesive

Secondary Camera

with 16’ cable*

SD Card(s)*

3G Cellular

Modem*

Key set for

Locking cover

Driver Facing Camera

Input

Power Adaptor

Connection

3G Modem Connection

(USB)

Power and I/O Wires

WHITE = Ignition (IGN+)

RED = Power (BAT+)

BLACK (x2) = GND (BAT-)

GREEN & ORANGE = Optional alarm

input triggers

Locking cover

(2 SD slots and 1 USB input inside)

Windshield bracket mount

www.smartwitness.com

3. Installation: First Steps

Use the provided keyset to unlock and remove the locking cover. To unlock the cover, insert the

provided keyset and turn counter-clockwise 90 degrees. Once unlocked, press firmly on the two

buttons on either side of the cover and pull the door away from the camera. Make sure to Hold the

KP1S body firmly in your other hand.

Once the locking cover is removed, you can adjust the angle of the camera to comply with the angle

of your windshield. When you are happy with the angle on the windshield, slide the case back onto

KP1S.

If SD cards were provided seperately, you should insert them at this time.

*If this is the WiFi version of KP1S, then the WiFi modem should be inserted at this time into the USB

input beneath the SD card slots.

Attach the provided 3M adhesive pad to the KP1S bracket and press firmly.

SD Card 1

SD Card 2

Camera lens

*USB input for Wi-Fi modem (optional)

Windshield

www.smartwitness.com

Secure the KP1S to the windscreen behind the rear view mirror, below the AS1 line. The camera lens

should be as high on the windshield as possible, but still within the windshield wiper zone. If

installing KP1S into a truck, FMCSA mandates that the camera portion of the device should

reside in the top 2 inches of the vehicle wiper sweep.

4. KP1S Power Adaptor and Wiring:

To connect the KP1S lead cable to the INT1S power adaptor, lining up the arrows on the silver cable

connectors and then push together. Twist the silver plate as shown below to secure the connection.

After Connecting the INT1S power cable to the KP1S power lead, lay out the power cable roughly

where it will run once hidden behind the vehicle's interior panels. This gives you an idea of where to

route the cable and how much slack to leave on the way down to the vehicle’s power source.

Secure the power cable extension into the headliner and down the A-Pillar. Route the power cable

around the side and behind the rest of the interior panels down towards the fuse box / power

IMPORTANT: Make sure that the glass is clean and dry before attaching. Hold the camera in

position with firm pressure for 30 seconds. The glass temperature should not be too hot or cold.

Please install in moderate temperature (recommended between 50°F ~ 80°F)

Power Cable to KP1S

Power Adaptor

Wiring Harness to

Vehicle

www.smartwitness.com

source. Make sure the vehicle is off and then connect the required wires to the vehicle, as shown

below in the wiring diagram.

1. Wiring Harness Diagram

Power (BAT+)

Ground (BAT-)

Ignition (IGN+)

Alarm In 1 (12V)

Alarm In 2 (NC/NO)

Alarm Out 2 (5V)

2. OPTIONAL: remote switch installation (your KP1S may not include this accessory)

3. OPTIONAL: If THE KP1S installation came with the basic 2-wire power adaptor, then connect the

Red wire to IGN+ and Black to BAT-

5. Connecting the Secondary Camera to KP1S ch2 input (optional)

The KP1S is equipped with a simple plug & play connection to a variety of SmartWitness 5V cameras.

Simply connect the 2.5mm male stereo connector of the SmartWitness camera (any model ending in

“-S”, such as the SVA030-S) into the female stereo input on the KP1 and mount the camera to the

customer-specified location in or around the vehicle. The most common installation of the secondary

camera is inside the main cabin and facing the driver. Use a securing tape on the 2nd camera stereo

connection, such as the silicone cold shrink which comes with the cellular modem.

A service loop is also recommended.

Required

Optional (verify with customer if orange,

green, or yellow wires will be used)

Alarm In 2

Ground (BAT-)

Model # SW-PB

Power (IGN+)

Ground (BAT-)

Model # KP1-PWK

1 ft. lead from camera.

2.5mm stereo - male

16’ extension cable (included with all

SmartWitness “-S” cameras)

3 ft. input cable from KP1S

2.5mm stereo - female

www.smartwitness.com

Secondary Camera installation examples:

6. Connecting 3G Cellular Modem (optional)

Connect the male USB port from the 3G Modem into the female USB port as seen in picture below.

Secure the male/female USB connection with the provided silicone cold shrink tape. The tape is self-

fusing and does not require heat to be applied. It stretches 300% and is fully fused within 24 hours

after application. It is best to stretch the tape, start from one end and overlap at an angle until you

reach the other end of the connector.

Secure the male/female USB connection with the provided silicone cold shrink tape. The tape is self-

fusing and does not require heat to be applied. It stretches 300% and is fully fused within 24 hours

after application. It is best to stretch the tape, start from one end and overlap at an angle until you

reach the other end of the connector.

On windshield using adhesive

On A-Pillar or headliner using screw mount

Model # INT3-GB

www.smartwitness.com

Remove the 3M adhesive backing and secure the modem to the windshield. The excess USB cable

and KP1S cable should be tucked neatly in the roof lining or along the edge of the windshield. It is

recommended to adhere the modem above the AS1 line, in the “blue zone” of the windshield

to reduce the amount of direct sunlight/heat. The modem should not be touching any part of

the vehicle frame or metal. DO NOT HIDE THE MODEM IN THE ROOF LINING OR A-PILLAR,

this will affect the cellular signal and hinder performance.

7. Final Steps

After installation of the KP1S and accessories into the vehicle (2nd camera, panic button, & 3G modem),

you can turn on vehicle ignition and the KP1S will power on. There will be a sequence of LED lights cycling

during boot process. Once boot up is complete, there will be a solid blue light. This indicates proper

operation and recording. If 3G modem is installed, the Green LED should also be solid on. If Green

light is blinking, then there is a server error or network error. If a red led comes on after bootup,

there is an error and you should contact your supplier. Please see step 8 for more details on LED

status indicators.

1) After you’ve set the camera angle, locked the

cover and removed the key, press the G-Sensor

calibration button once (small red button ABOVE

the panic button). This will also capture an image

from each camera and send to the server to confirm

camera operation and proper camera field of views.

The blue LED will flash rapidly for a few seconds when the calibration button is pressed.

2) Verify the Blue and Green LED lights on the camera are solid and not blinking. Once the camera makes

successful connection to the server, it may apply updated configuration file and/or firmware. In this case, the

camera will automatically re-boot to apply the new settings/firmware. Please make sure the camera reboots

and goes back to solid blue and green LED. *NOTE: only the Blue and Green LEDs should be on. If Red LED is

on, see Troubleshooting/FAQ section for more information.

3) Verify the 3G Modem “Link” LED light is on and blinking slowly

4) Please visit http://install.smartwitness.com to complete the installation form and click submit.

5) Give the provided keyset and any extra parts/accessories to the fleet owner/administrator as well as a copy

of the installation report.

www.smartwitness.com

8. Troubleshooting

The KP1S has a solid RED light on as well as solid GREEN and Blue

oSolid RED LED indicates the 2nd camera channel is not receiving video signal. Please check the

camera connection.

The KP1S Blue light is solid but the Green light is blinking or off

oCheck the “Link” LED on the modem.

If Link LED is solid, check to make sure the SIM card is inserted properly

If Link LED is OFF, check the USB connection of the cable and modem

If Link LED is blinking and the KP1S Green LED is also blinking, it may be a camera

configuration issue or server issue. Please contact SmartWitness.

The 3G modem Link LED is solid on

oThe SIM card is not registering with the cellular network. Please verify the SIM is inserted correctly,

as seen on page 7.

oIf it looks to be inserted correctly, please remove and re-insert the SIM card and try again

oPower cycle the camera

The KP1S RED LED is blinking

oThere is an SD card error/corruption. Please replace the SD card or contact SmartWitness

3G Modem LED specification

“LINK” Status LED

Signal Strength LEDs

LED

www.smartwitness.com

9. KP1S LED Specification

1.1. Startup, Data Buffering to NAND (0 to 90seconds after power on)

KP1 BOOT UP SEQUENCE

LED

(red)

(orange)

(blue)

(green)

Start

1st step ( 0~12sec)

2nd step (12 ~ 30sec)

charging capacitor

ON & OFF

3rd step (31 ~ 60sec) begin

recording video to NAND

memory

ON & OFF

4th step (61 ~ 89sec)

ON & OFF

5th step (90sec + 1sec )

*IF SD card is blank (not initialized), KP1 will blink RED led slowly for about 1 minute, then automatically

initialize the SD card, apply the latest NAND settings, and reboot.

30sec

Boot up complete

Startup

Normal Operation

Power OFF

0sec

90sec

Tabla de contenidos

Otros manuales de Cámara de salpicadero de Smart Witness

Smart Witness

Smart Witness CP1 Manual de usuario

Smart Witness

Smart Witness AP1 Manual de usuario

Smart Witness

Smart Witness SVC1080 Manual de usuario

Smart Witness

Smart Witness SVC1080-LCS Manual de usuario

Smart Witness

Smart Witness SVC100 Manual de usuario

Smart Witness

Smart Witness KP1S Manual de usuario

Smart Witness

Smart Witness KP1 Manual de usuario

Smart Witness

Smart Witness KP1S Manual de usuario

Smart Witness

Smart Witness SVC150GPS-LC Manual de usuario

Smart Witness

Smart Witness SVA035-2 Manual de usuario

Smart Witness

Smart Witness SVC150GPS Manual de usuario

Smart Witness

Smart Witness SVC400GPS Manual de usuario

Smart Witness

Smart Witness SVC-F Series Manual de usuario

Smart Witness

Smart Witness SVC050 Manual de usuario

Smart Witness

Smart Witness SVC-V Manual de usuario

Smart Witness

Smart Witness AP1 Dimensiones

Smart Witness

Smart Witness KP1S Manual de usuario

Smart Witness

Smart Witness KP1 Manual de usuario

Smart Witness

Smart Witness SVC-S Manual de usuario

Smart Witness

Smart Witness KP2 Manual de usuario

Smart Witness

Smart Witness DDC-200 Manual de usuario

Smart Witness

Smart Witness SVA035 Manual de usuario

Smart Witness

Smart Witness SVC100GPS Manual de usuario

Smart Witness

Smart Witness SVC100GPS Manual de usuario

Manuales populares de Cámara de salpicadero de otras marcas

Cansonic

Cansonic UltraDuo Z2 Manual de usuario

Gazer

Gazer F720 Manual de usuario

HP f500g Manual de usuario

Xblitz

Xblitz TANGO 4K Manual de usuario

Rexing

Rexing M1 Manual de usuario

Maka Technologies

Maka Technologies Marbella MXPro Manual de usuario

NESA

NESA NRC-80DLM Instrucciones de instalación y funcionamiento

Kaiser Baas

Kaiser Baas R20 Manual de usuario

Boyo

Boyo VTM43TC Manual de usuario

Minolta

Minolta MNCD37 Manual de usuario

Thinkware

Thinkware FA10 Manual de usuario

Momento

Momento MD-5200 Manual de usuario

BlackVue

BlackVue DR590X-1CH Manual de usuario

HP F300 Manual de usuario

CammSys

CammSys BlackSys BH-300 Manual de usuario

Snooper

Snooper DVR-2HD Manual de usuario

Lukas

Lukas Q900 Manual de usuario

RVS

RVS 450C Manual de usuario