Smart Technologies SBID-MX265 Manual de instrucciones

Was this document helpful?

smarttech.com/docfeedback/171257

SMARTBoard MX series

interactive displays

INSTALLATION AND MAINTENANCE

FOR MODELS:

lSBID-MX265

lSBID-MX275

lSBID-MX286

smarttech.com/kb/171257

Trademark notice

SMARTBoard, smarttech, the SMART logo and all SMART taglines are trademarks or registered trademarks of SMARTTechnologiesULC in the U.S. and/or other

countries. All third-party product and company names may be trademarks of their respective owners.

translated into any language in any form by any means without the prior written consent of SMARTTechnologiesULC. Information in this manual is subject to change

without notice and does not represent a commitment on the part of SMART.

This product and/or use thereof is covered by one or more of the following U.S. patents:

www.smarttech.com/patents

05-2018

i smarttech.com/kb/171257

Important information

IMPORTANT

There are critical software updates for the display that you need to install to ensure the display is

fully functional and provides the best experience. Connect the display and iQ appliance to a

wired or wireless network with Internet access to automatically download and apply these

updates as well as future updates.

WARNING

lFailure to follow the installation instructions shipped with the SMART product could result in

injury and product damage which may not be covered by the warranty.

lDo not open or disassemble the SMART product. You risk electrical shock from the high

voltage inside the casing. Opening the casing also voids the warranty.

lDo not stand (or allow children to stand) on a chair to touch the surface of the SMART

product. Rather, mount the product at the appropriate height.

lTo reduce the risk of fire or electric shock, do not expose the SMART product to rain or

moisture.

lIf the SMART product requires replacement parts, make sure the service technician uses

replacement parts specified by SMARTTechnologies or parts with the same characteristics

as the original.

lEnsure that any cables that cross the floor to the SMART product are properly bundled and

marked to avoid a trip hazard.

lDo not insert objects inside the cabinet ventilation holes, because they could touch

dangerous voltage points and cause electric shock, fire or product damage which may not

be covered by the warranty.

lDo not place heavy objects on the power cable. Damage to the cable could cause shock,

fire or product damage which may not be covered by the warranty.

lUseonly extension cords and outlets that can fully accommodate the display’s polarized

plug.

IMPORTANT INFORMATION

ii smarttech.com/kb/171257

lUse the power cable provided with the display. If a power cable is not supplied, contact

your supplier. Use only power cables that match the AC voltage of the power outlet and that

comply with your country’s safety standards.

lIf the glass is broken, do not touch the liquid crystal. To prevent injury, handle glass

fragments with care when disposing of them.

lDo not move or mount the display by connecting rope or wire to its handles. The display is

heavy, and failure of the rope, wire or handle could lead to injury.

lUse only VESA®-approved mounts if using a mount other than the one supplied with the

display..

lDisconnect all of the display’s power cables from the wall outlet and seek assistance from

qualified service personnel if any of the following occur:

oThe power cable or plug is damaged

oLiquid is spilled into the display

oObjects fall into the display

oThe display is dropped

oStructural damage, such as cracking, occurs

oThe display behaves unexpectedly when you follow operating instructions

lBefore inserting or removing the iQ appliance from the display, turn off the display using the

switch at the back of the display. See Open Pluggable Slot computer (OPS) disclaimer for

more information.

CAUTION

lTurn off the display before cleaning its screen. Otherwise, you may scramble the desktop

icons or inadvertently activate applications when you wipe the screen.

lAvoid setting up and using the SMART product in an area with excessive levels of dust,

humidity and smoke.

lMake sure an electrical socket is near the SMART product and remains easily accessible

during use.

IMPORTANT INFORMATION

iii smarttech.com/kb/171257

lThe SMART product should be used only with European TN and TT power distribution

systems.

It is not suitable for older, IT-type power distribution systems found in some European

countries. This system (IT-type) is widely used isolated from earth, in some installations in

France, with impedance to earth, at 230/400V, and in Norway, with voltage limiter, neutral

not distributed, at 230V line-to-line.

Contact qualified personnel if you’re uncertain of the type of power system available where

you’re installing the SMART product.

lThe accessory slot’s maximum available power is 60 W. The slot is not a limited power

source. To reduce the risk of fire, make sure that accessories connecting to the slot satisfy

the fire enclosure requirements of IEC60950-1.

lYou must connect the USB cable that came with the SMART product to a computer that has

a USB compliant interface and that bears the USB logo. In addition, the USB source

computer must be compliant with CSA/UL/EN 60950 and bear the CE mark and CSA and/or

UL Mark(s) for CSA/UL 60950. This is for operating safety and to avoid damage to the

SMART product.

IMPORTANT

lThe following are the normal operating requirements for the display, including AM module

and speakers:

Model Power requirements

SBID-MX265 100V to 240V AC, 50 Hz to 60 Hz, 115 W max

SBID-MX275 100V to 240V AC, 50 Hz to 60 Hz, 224 W max

SBID-MX286 100V to 240V AC, 50 Hz to 60 Hz, 265 W max

lFor additional requirements and other information, refer to the display’s specifications (see

More information on page9).

Federal Communication Commission

interference statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. this device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT INFORMATION

iv smarttech.com/kb/171257

NOTE

This equipment has been tested and found to comply with the limits for a Class A digital device,pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

CAUTION

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate this equipment.

Radiation exposure statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should

be installed and operated with minimum distance of 20 cm between the antenna of this device and allnearby persons. This

transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

Innovation, Science and Economic Development

Canada statement

This device complies with RSS-247 of the Innovation, Science and Economic Development Canada Rules. Operation is subject

to the following two conditions:

1. This device may not cause harmful interference, and

2. this device must accept any interference received, including interference that may cause undesired operation.

Radiation exposure statement

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should

be installed and operated with minimum distance of 20 cm between the antenna of this device and allnearby persons. This

transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

Cet appareil est conforme à la norme ISED CNR-247 pour les appareils radio agréés. Son fonctionnement est soumis aux deux

conditions suivantes:

1. le dispositif ne doit pas produire de brouillage préjudiciable, et

2. ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement

indésirable.

Déclaration d’exposition aux radiations

Cet équipement est conforme aux limites d’exposition aux rayonnements ISEDétablies pour un environnement non contrôlé.

Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre

corps. Cet émetteur ne doit pas être co- implantés ou exploités conjointement avec une autre antenne ou émetteur.

EU declaration of conformity: AM40

Hereby, SMART Technologies ULC declares that the radio equipment type OPS, AM40 is in compliance with Directive

2014/53/EU.

The fulltext of the EU declaration of conformity is available at the following internet address: smarttech.com/compliance

The frequency band and the maximum transmitted power in EU are listed below:

IMPORTANT INFORMATION

v smarttech.com/kb/171257

Transmitting Band (MHz) Maximum Transmit Power EIRP (dBm)

2400–2483.5 19

5150–5350 16

5470–5725 16

Restrictions in

AT/BE/BG/CZ/DK/EE/FR/DE/IS/IE/IT/EL/ES/CY/LV/LI/LT/LU/HU/MT/NL/NO/PL/PT/RO/SI/SK/TR/FI/SE/CH/UK/HR. 5150MHz-

5350MHz is for indoor use only.

CAUTION: EXPOSURE TO RADIO FREQUENCY RADIATION

This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should

be installed and operated with minimum distance 20 cm between the radiator and your body.

vii smarttech.com/kb/171257

Contents

Important information i

Federal Communication Commission interference statement iii

Innovation, Science and Economic Development Canada statement iv

EU declaration of conformity: AM40 iv

Chapter 1: Welcome 1

About this guide 1

About the SMARTBoard MX 2

Components 3

Related products 7

More information 9

Chapter 2: Installing the display 11

Transporting the display 11

Installing the display on a wall 13

Installing the display on a stand 20

Chapter 3: Connecting power and devices 21

Connecting the iQ appliance 21

Connecting power 22

Connecting to a network 22

Connecting cables for room computers, guestlaptops and other input sources 23

Connecting external speakers 25

Connecting room control systems 26

Connector reference 27

Chapter 4: Configuring the display 31

Turning on the display for the first time 32

Connecting the display and iQ appliance to a network 33

Updating system software 40

Updating iQ system software 40

Updating the display’s firmware 41

Locking down the Settings app for iQ system software 43

Switching the iQ system software to the Beta channel 44

Adding or removing apps from the launcher 47

Enabling the Whiteboard Library 47

Chapter 5: Configuring connected computers 49

Installing SMART software on connected computers 49

CONTENTS

viii smarttech.com/kb/171257

Setting connected computers’ resolutions and refresh rates 50

Chapter 6: Maintaining the display 51

Checking the display installation 51

Cleaning the screen 51

Cleaning the touch sensors 52

Maintaining ventilation 53

Preventing condensation 53

Replacing the pens 53

Turning the display off and back on 53

Resetting the display 54

Removing and transporting the display 54

Chapter 7: Troubleshooting 57

Troubleshooting the display 57

Troubleshooting the iQ system software 62

Referring to the SMART knowledge base for additional troubleshooting information 73

Contacting your reseller for additional support 73

Appendix A: Using iQ system settings 75

Network settings 75

Application settings 75

System settings 76

Appendix B: Using display settings on your SMARTBoard MX 79

Accessing the display’s settings 79

Exiting the display’s settings 79

Network 80

Screen lock 80

Advanced 81

Update 82

Recovery 82

About 83

Appendix C: Remotely managing the display 85

Connecting a computer to the display 86

Configuring the computer’s serial interface settings 86

Power states 87

Commands and responses 88

Commandinventory 89

Resolving issues with remote management 92

Appendix D: Identifying your display 93

Identify your display 93

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Monitor de Smart Technologies

Smart Technologies

Smart Technologies SMART Board 2000 series Manual de usuario

Smart Technologies

Smart Technologies Board 7000 Series Manual del producto

Smart Technologies

Smart Technologies Sympodium DT770 Instrucciones de instalación y funcionamiento

Smart Technologies

Smart Technologies SMART Board 7000 R Series Manual de usuario

Smart Technologies

Smart Technologies SMART Podium ID422w Interactive Pen Display Instrucciones de montaje

Smart Technologies

Smart Technologies SMART Board SBID Interactive Display 6052i Manual de usuario

Smart Technologies

Smart Technologies Smart Board MX Series Manual del producto

Smart Technologies

Smart Technologies Sympodium DT770 Manual de usuario

Smart Technologies

Smart Technologies SMART Board 6000S Manual de usuario

Smart Technologies

Smart Technologies SMART Board SBID-7075P Manual de usuario

Smart Technologies

Smart Technologies SMART Podium ID422w Interactive Pen Display Manual de usuario

Smart Technologies

Smart Technologies SMART Board MX Pro Series Manual del producto

Smart Technologies

Smart Technologies SB885 Manual de usuario

Smart Technologies

Smart Technologies Sympodium MP250 Manual de usuario

Smart Technologies

Smart Technologies Sympodium ID350 Manual de usuario

Smart Technologies

Smart Technologies SMART Board MX series Manual de usuario

Smart Technologies

Smart Technologies SMART Board SBID-7275P Guía

Smart Technologies

Smart Technologies SB880 Manual de usuario

Smart Technologies

Smart Technologies SMART Board MX100 series Manual de instrucciones

Smart Technologies

Smart Technologies SMART Board 6000S Manual del producto

Smart Technologies

Smart Technologies Board SBID-7275-V2 Manual del producto

Smart Technologies

Smart Technologies SMART SBID8055i-G3 Manual de usuario

Smart Technologies

Smart Technologies SBID-7275R Manual de usuario

Smart Technologies

Smart Technologies SPNL-6 65-V2 Series Manual de usuario

Manuales populares de Monitor de otras marcas

Linear Acoustic

Linear Acoustic LQ-1000 Manual de usuario

AOC

AOC I2579V Manual de usuario

Gateway

Gateway FPD1520 Manual de usuario

Furuno

Furuno Mu 120c Manual de usuario

Asus

Asus VB171D - 17" LCD Monitor Manual de usuario

Dell

Dell S2230MX Instrucciones de uso

Philips

Philips 107C64 Manual de usuario

Dell

Dell S2409WFP Manual de usuario

EverFocus

EverFocus EN-7517E Manual de usuario

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manual de usuario

Dell

Dell Precision 7680 Manual de instrucciones

LG 50PM1M - - 50" Plasma Panel Manual de usuario

Bosch

Bosch DDU 9 Manual de usuario

Acer

Acer A231HL Manual de usuario

Philips

Philips 86BDL4152T Manual de usuario

NEC

NEC AccuSync LCD5V Manual de usuario

Emay

Emay SleepO2 Manual de usuario

IBM

IBM 6360 Instrucciones de instalación