Smart Candle LV96 Manual de usuario

The Low Voltage lighting system can power up to 96 candle pods split over 4 different independent channels.

24 candles can be powered per output channel.

Low Voltage is a revolutionary lighting system which has been purposely designed to minimise interaction

with electronic candles. The candles can be powered at the touch of a button using mains power. No need

to change any batteries or turning on by hand or remote control.

Items Required for LV96 System:

LV96 Control Box

Power Adaptor with A/C Lead

Low Voltage Candles

Low Voltage Cable

Plug and Go connection cables (Optional)

Installation Items Required:

Number 1 Size Philips style screw driver

Wire Stripper

Wire Cutter

Power Lead:

The power adaptor that is supplied with the control box is a switch mode unit, it will operate from 100V –

240 volts.

First connect the small socket from the power adaptor into the input socket on the control box (SEE FIG 1).

Then insert the mains plug into a A/C mains outlet socket.

The control box can be mounted onto a wall or shelf with the designated screw holes that are located on

either end of the control box. (SEE FIG 2)

LV96 Instructions

Installation:

The Low Voltage systems are designed to check that each pod is being wired in to the system correctly i.e. polarity, as

you install. The pods which are being installed will have an LED Indicator on them. For this feature to work, it is

important that the control box is connected to the mains via the power lead, and the switch is

in the on position. The control box LED will illuminate “RED”showing that power is running to the control box

(SEE FIG 1). When pods are installed into the system the LED indicators will illuminate if they are correctly

wired and installed.

Wiring the Pods:

**Make sure the Control box power is switched ON**

Polarity:

The “Copper”coloured wire should always be connected to the “+”connectors at the control box terminals

and candles pods.

The “Silver”cable should be connected to the “-”connectors at the control box terminals and candle pods.

Connecting the candles:

Each control box has 4 output channels. Each output channel can run a maximum of 24 candles.

Using a screwdriver loosen the output channel wire securing screws. Strip the plastic from the low voltage

cable by approximately 1cm and insert the cables observing the correct polarity as explained above. Copper

colour into “+”and Silver into “-”. Once both cables are in their respective terminals, secure the screws

with a screw driver.

This process is repeated per output channel. (SEE FIG 3, FIG 4)

Connecting pods into the system:

Unscrew cable connection securing screws on the pods. Strip the plastic from the wire by approximately 1cm

and as above insert the correct colour wire into their respective terminals. COPPER INTO “+”and SILVER

INTO “-”. Once this step is completed, secure the screws back into place.

Plug and Go connectors are available. These simply plug from port to port located on each candle pod.

If the LED indicator is GREEN on the candle pod this has been done correctly.

Repeat this process from Pod to Pod. (SEE FIG 5, FIG 6, FIG 7, FIG 8)

Concealing Cable:

For situations where the cable needs to be concealed the output cables can be clipped to the under side of

the pods using the clips on the underside of the pod. (SEE FIG 9)

The pods can be secured to a surface using the screw holes integrated into the pod. (SEE FIG 10)

Fitting the candles:

Low Voltage candles are extremely easy to install. Simply place the Low Voltage candles onto their

corresponding pods, making sure the socket on the bottom of the candle is fully placed onto the power

socket on the pods. (SEE FIG 11, FIG 12)

LV96 Instructions

Control Box Features:

On/Off Mode

Reset Button (Individual Channel on and off)

Timer Mode

On/Off Mode: When in the “ON”position the whole system (every channel) will remain on until the switch is

turned to the “OFF”position.

Reset Button: Press and hold the reset button on any channel to turn this individual channel on or off. A

“RED LED”will illuminate and the candles in this channel will turn off. Press once again and the “RED LED”

will go out and the candles for this channel will turn back on. Repeat as needed on any channel.

If switched to "Timer" mode then you can select the amount of time you want the system on for

TIMER PERIOD 8 / 12 / 16 Hours

TIMER RESET

The timer is based on a 24 hour period , so if you select 12 hours then the system will be "On" for 12

Hours and "Off" for 12 hours.

Select the time you want , 8 , 12 , or 16

When you have set the switch to the desired time Press the "TIMER RESET" Button located next to the timer

mode switch. Pushing the button will start the timer system if you want to reset the time then press the

timer reset button again;

E.G: 12 Hour Timer

Time on 12.00 Noon: Press the reset button at 12 Noon and At Midnight the system will turn Off

Note switching between timer settings will reset the timer

If the control box power is switched off at the A/C supply this will also reset the timer. If the power to the

control box has been interupted then the timer will need to be reset

Other Information:

When the system is switched "ON" , or switched from "Normal Mode to "Timer Mode" or switched between

"Timer" settings i.e. 8 hours to 12 hours the "RED" LED Indicator lights will come on and go off in sequence

from right to left. This is normal and the system is self re-setting.

RESET LED Indicator:

If there is a problem in a certain channel the Reset LED will illuminate for that channel, this could be caused by:

Polarity being incorrect

Too many candles in the line (24 Maximum per output channel)

NOTE: This will only occur when candles are fitted onto their respective pods.

(SEE FIG 13 –WHOLE PAGE)

LV96 Instructions

RESET LED Indicator on Power Lead:

This Low Voltage system has overload/surge protection. Should anything power related occur a “RED LED”will

illuminate on the little box on the power lead. By pressing the “reset”button next to the LED this will reset

the system. Once this is pressed the system will function as normal.

Note: By adding too many candles into the system could cause this to illuminate.

A MAXIMUM OF 96 CANDLES CAN BE USED PER SYSTEM

A MAXIMUM OF 24 CANDLES PER OUTPUT CHANNEL CAN BE USED

A MAXIMUM of 25 Metres to the first candle can be achieved. Thereafter between candles 2 metres can be

achieved. (Candles could go dim if more than this is attempted)

Fig$2 . Fig$3 . Fig$4.

Fig$5 . Fig$6. Fi g$7. Fig$8 .

Fig$9 . Fig$11 . Fig$12.

Normal/OFF/Timer Ti m er$ 8 /1 2 / 1 6 $ Hou rs

Ti m er$ Res et

Fig$1 3.

Fig$1 0.

Fig$1 .

LV96 Instructions

Tabla de contenidos

Manuales populares de Accesorios de iluminación para el hogar de otras marcas

Coopers of Stortford

Coopers of Stortford H700 Manual de usuario

LIVARNO home

LIVARNO home 427687 2301 Manual de usuario

Alpine

Alpine CRD100S-MC Manual de usuario

IKEA

IKEA ORMANÄS Manual de usuario

Home Accents Holiday

Home Accents Holiday TY444-1711-5 Manual de usuario

Kingfisher

Kingfisher 3663602491309 Manual de usuario

EKVIP

EKVIP 022464 Manual de usuario

Tronix

Tronix 033-028 Manual de usuario

Goobay

Goobay 57940 Manual de usuario

Home Accents Holiday

Home Accents Holiday 23RT04623112 Manual de usuario

Philips

Philips 6915160PH Manual de usuario

MELINERA

MELINERA Z31531A Manual de usuario

abc home garden

abc home garden 22594 Manual de usuario

IKEA

IKEA KALLT Manual de usuario

Gainsborough

Gainsborough K337 Manual de usuario

Costco

Costco 1900354 Manual de usuario

Home Accents Holiday

Home Accents Holiday TY415-1911 Manual de usuario

Home Accents Holiday

Home Accents Holiday TY476-1611-1 Manual de usuario