SKYLUX Vertical sunblind 78065 Manual de usuario
VERANDA
Vertical sunblind
Mounting instructions
EN
Art.N° 78065
E_MH_Mounting_instructions_Skylux_Vertical_sunblind 01/10/2020
2/16
Safety
Take the necessary and required safety precautions, such as safety nets and lifelines when installing from the
outside, safety goggles, gloves, hard hat, etc.
Do not step on the glass.
Falling from height
• When using ladders to go on the roof:
- Ladder in good condition?
- Set up correctly at an angle of 75°?
- Secured below and on top against moving?
- Don’t take heavy material with you on the ladder (3-point contact rule)! If possible,
use a crane to lift the material.
• If you are going on the roof, make sure there is a walking surface that is wide enough and that
supports on the beams of the lower structure.
•When using an aerial work platform: always wear and secure your harness (mandatory)! Leaving
the cage is forbidden.
• Never walk backwards on a roof, always walk forwards.
• Make sure there’s enough light in the working zone.
Low-hanging obstacles and falling loads
• Forbidden to walk under or within a radius of 1 m of a hanging or lifted load.
• Demarcate the danger zone below the zone where there is a risk of material falling down
during the installation of the veranda.
• It’s prohibited to enter these danger zones during construction.
Crushing hazard
• All working tools are in good condition, provided with a valid CE label and all necessary safety
regulations. These cannot be removed.
• People who use these working tools are educated for this purpose. Protections are always
present on all working tools. They are in good condition and need to be set correctly.
Tripping/falling
•Safety is key and it begins with order and tidiness. Clean everything immediately, leave nothing
lying around.
• Trash needs to be sorted.
• Be cautious with electric cables (danger of tripping/falling). Never walk backwards!
• Make sure there’s enough light in the working zone.
01/10/2020 3/16
E_MH_Mounting_instructions_Skylux_Vertical_sunblind
Sharp objects
• Make sure your fingers/hands are not pinched and watch out for cuts while handling veranda
parts.
• Be careful where you put your hands during the installation.
• Wearing cut-resistant gloves is mandatory.
Ergonomics
• Always lift loads correctly: bend your knees, move your feet instead of forcing your spine, lift
as close to your body as possible.
• Parts of more than 25 kg must be lifted with at least 2 persons.
Personal protective equipment
• Work clothes, safety shoes and helmet are mandatory for everyone.
• Lifeline and harness are mandatory if the edge is not secured enough or if there are no safety nets below the
veranda roof. They are also necessary when using an aerial working platform.
• Use gloves when handling veranda parts.
• Safety glasses and hearing protection are mandatory when using saws / grinders.
Always perform a Last Minute Risc Analysis!
If in doubt: STOP! Do not take unnecessary risks. Ask your supervisor if needed.
E_MH_Mounting_instructions_Skylux_Vertical_sunblind 01/10/2020
4/16
SAFETY p. 2
CONTENT p. 4
INTRODUCTION p. 4
USE OF THE PRODUCT p. 4
OVERVIEW OF PROFILES AND PARTS p. 5
INSTALLATION p. 6
MAINTENANCE p. 15
GUARANTEE p. 15
Content
Introduction
The installation of the product must be carried out by professionals. An incorrect installation can cause damage.
It is important to notify the installer of the information in this manual.
These instructions must be followed at all times.
Failure to comply with these instructions relieves the manufacturer of his liability obligation.
You can always contact the Skylux technical service if you have any questions about the installation of this product.
Random interventions by unauthorised personnel for repairs or changes to the product can cause severe damage
to the product or the residence.
If the product installation is planned for later, the product must not be stored in a highly damp or aggressive
environment.
Use of the product
This product is meant to be used as a sunblind, this means only for protection against the sun.
To ensure a correct use, instructions are listed in this manual.
Using the product in any way other than the intended purpose described in this manual is incompatible with the
functional specification.
01/10/2020 5/16
E_MH_Mounting_instructions_Skylux_Vertical_sunblind
Overview profiles and parts
Required tools
- Allen key 3
- Spirit level
- Meter
- Drill
4 mm drill
5 mm drill
10 mm drill
TX25 bit
Casing
Rails
VPL1342 Adapter profile
VPL432 L-profile
VTSCR.002 Attachment screws
E_MH_Mounting_instructions_Skylux_Vertical_sunblind 01/10/2020
6/16
Installation
Before attaching the rail to the posts,
we advise you to recheck the measurements.
Please make sure that the rails are always parallel towards each other and perpendicular towards the casing.
This is very important because an incorrect installation causes wrinkles in the fabric or permanent damage.
90°
=
=
D +0/-1mm
Hscn +0/-1 mm
=
=
B +0/-1mm
(HG + HN)+0/-1mm
01/10/2020 7/16
E_MH_Mounting_instructions_Skylux_Vertical_sunblind
Casing 131:
Casing 103:
Climalux GX
Climalux GXLX
Climax GD1
Side veranda
Climax Panorama GDG
Climax GD2
VPL1342
B or D
130 mm
102 mm
50 mm max 300 mm
ø 5 mm
ø 5 mm
ø 5 mm
E_MH_Mounting_instructions_Skylux_Vertical_sunblind 01/10/2020
8/16
Pre-drill reinforcement profile with Ø 4 mm.
VPL1342 VTSCR.002
VTSCR.002
Climalux GXLX
VTSCR.002
Climax Panorama
VTSCR.002
Climax GD1
ZSG
Climax GD2
VTSCR.002
Climalux GX
01/10/2020 9/16
E_MH_Mounting_instructions_Skylux_Vertical_sunblind
Unscrew the cover plate from the rails and take out the PVC part for the installation. Use the 3 mm Allen key.
*Drill holes in the front of the rail to secure it.
Do this where the foam is situated (on the inside of the rail).
ø 10 mm
ø 5 mm
*
PVC part
46 mm
32 mm
E_MH_Mounting_instructions_Skylux_Vertical_sunblind 01/10/2020
10/16
Slide the casing on the rail.
Put the casing perpendicular on the rail. Be careful not to break the ends of the side parts.
Electric connection of the actuator
Before installing the sunblind, you need to drill a hole for the control unit (actuator).
- Check the position of the actuator cable (left or right).
- Let the power cable go through the support or next to the side clips.
Power cable
Tabla de contenidos
