Skyinnov M300 Manual de usuario

Manual_Pack-M300_en_V1

Installation manual

Trichogramma Pack

M300

Manual_Pack-M300_en_V1

Summary :

1. Introduction ________________________________________________ p3

2. Assembly___________________________________________________ p4

3. Setup______________________________________________________ p8

Manual_Pack-M300_en_V1

Introduction :

The trichogramma pack for DJI Matrice 300 is composed of the following elements:

-The Trichogramma system T-Drop and its 8 liter tank

-The T-Box System

-The supports of fixations necessary for its installation

-A raised landing gear

This manual is intended for the assembly of the pack,

For the use of the spreader and the autonomous system please refer to their manual:

- T-Drop Manual

- T-Box Manual

Manual_Pack-M300_en_V1

Assembly :

1) Assembling the lower attachment point on the T-Drop:

Remove the two M3x6 FHC screws under the screen and replace

them with the two M3x10 BHC screws provided to secure the carbon

plate of the bottom bracket.

Manual_Pack-M300_en_V1

2) T-Box assembly and top mount on the T-Drop :

Use the 4 supplied M3x15 CHC screws to mount the T-Box to the

spreader tray by sandwiching the carbon plate of the bracket.

(The antennas must be opposite to the screen)

Fix with the 4 supplied M3 nuts from the inside of the tank.

(The 4 holes in the tank may need to be enlarged to 3.5mm)

Manual_Pack-M300_en_V1

3) Cable attachment :

Attach the cable to the bracket using the supplied cable tie.

Do not run the cable over the GPS

Then check that the cable cannot pass through the propeller.

Manual_Pack-M300_en_V1

4) Assembly on the M300:

For more ease, the assembly is done with the M300 upside down

as for the DJI payload.

-Slide the spreader between the two legs until it rests on the stops.

-Clip the bottom bracket onto the tube.

-Close the two upper brackets and lock them with the hand screws provided.

Manual_Pack-M300_en_V1

Setup :

To work with the T-Box, your T-Drop spreader must follow this configuration:

ARM : off

DROP mode : I/0

This manual is intended for the assembly of the pack,

For the use of the spreader and the autonomous system please refer to

their manual:

- T-Drop Manual

- T-Box Manual

Otros manuales de Accesorios para drones y cuadricópteros de skyinnov

skyinnov

skyinnov T-Box Manual de usuario

Manuales populares de Accesorios para drones y cuadricópteros de otras marcas

A2Z Drone Delivery

A2Z Drone Delivery RDS2 Manual de usuario

ParaZero

ParaZero SafeAir Mavic Manual de usuario

JT SS125 Manual de usuario

dji

dji Zenmuse X9 Manual de usuario

dji

dji Goggles Manual de usuario

dji

dji E7000 Manual de usuario

RunCam

RunCam Phoenix HD Manual de usuario

DRS

DRS DRS-M210-V2 Manual de usuario

Kogan

Kogan 4K GALAXY Manual de usuario

Opale Parachutes

Opale Parachutes SAFETECH 3.2K ST60 Manual de usuario

Flycolor

Flycolor X-Cross Mini 4in1 Manual de usuario

ParaZero

ParaZero SafeAir Phantom Manual de usuario

dji

dji PHANTOM 2 VISION PLUS Manual de usuario

HOBBYEAGLE

HOBBYEAGLE A3 Mini Manual de usuario

dji

dji AGRAS T50 Manual de usuario

TCMM RC

TCMM RC AC 220 Manual de usuario

iKarus

iKarus Profi Gyro Manual de usuario

R2TECK

R2TECK NEXG1 Manual de usuario

skyinnov M300 Manual de usuario

Manuales populares de Accesorios para drones y cuadricópteros de otras marcas