skilsaw SPT5007-EA Manual de usuario
IMPORTANT
Read Before Using
◆
IMPORTANT
Lire avant usage
◆
IMPORTANTE
Leer antes de usar
For English Version
See page 2
◆
Version française
Voir page 53
◆
Versión en español
Ver la página 117
Instruction Manual
Mode d'emploi
Manual de instrucciones
1-877-SKIL999 (1-877-754-5999) www.skilsaw.com
Call Toll Free for Consumer Information & Service Locations
Pour obtenir des informations et les adresses de nos centres de service après-vente, appelez ce numéro gratuit
Llame gratis para obtener información para el consumidor y ubicaciones de servicio
For English Version
See page 2
◆
Version française
Voir page 18
◆
Versión en español
Ver la página 34
EARLY ENTRY ATTACHMENT
ATTACHEMENT À PÉNÉTRATION PRÉCOCE
ADITAMENTO DE ENTRADA TEMPRANA
SPT5007-EA
-2-
Table of Contents
Page
Safety Symbols..........................2
Intended Use............................3
Unpacking and Checking Contents ..........3
Getting to Know Your Early Entry Attachment .4
Safety Symbols
The denitions below describe the level of severity for each signal word. Please read the manual and
pay attention to these symbols.
This is the safety alert symbol. It is used to alert you to potential personal
injury hazards. Obey all safety messages that follow this symbol to avoid
possible injury or death.
DANGER DANGER indicates a hazardous situation which, if not avoided, will result
in death or serious injury.
WARNING WARNING indicates a hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION CAUTION, used with the safety alert symbol, indicates a hazardous situ-
ation which, if not avoided, will result in minor or moderate injury.
Page
Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Operation .............................13
Maintenance ...........................16
WARNING Familiarize yourself with Oper-
ating/Safety instructions (man-
ual) for Skilsaw SPT79A. The manual for SPT79A
contains additional information that is not covered
in this manual. If the SPT79A manual is missing,
please download a copy from
www.skilsaw.com/service-manuals.
WARNING
Some dust created by power
sanding, sawing, grinding, drill-
ing and other construction activities contains
chemicals known to the State of California to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
–Lead from lead-based paints,
–Crystalline silica from bricks and cement and
other masonry products, and
–Arsenic and chromium from chemically-
treated lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a
well-ventilated area, and work with approved
safety equipment, such as those dust masks that
are specially designed to lter out microscopic
particles.
-3-
This attachment allows SKILSAW SPT79A Medusaw™ walk behind saw to function as an early
entry concrete saw and is designed for residential and light commercial projects. Early entry saw
controls random cracking of the concrete by making early contraction cuts, often within 1 – 2 hours
after the nishing process is complete. The combination of the spring-loaded skid plate and the early
entry diamond wheel specically designed for this application, allows early entry sawing while min-
imizing chipping and spalling of the cut edges.
Intended Use
WARNING
For your own safety, never
connect the saw to a power
outlet until all assembly steps are completed
and until you have read and understood the
entire instruction manual.
TOOLS REQUIRED: A screwdriver that accepts
standard 1/4" hexagonal bits is required to use
the T25 torx bit.
Separate all parts from the packing materials and
check each one against the “Loose Parts List" to
make sure that all items are accounted for before
discarding any packing material.
WARNING If any parts are missing, do
not attempt to assemble the
early entry attachment until the missing parts
are obtained and are installed correctly.
LOOSE PARTS LIST
Item Description Qty
AEarly entry attachment main
body 1
BFront locking bolt 1
C1-1/2 inch depth stop 1
DHex nut for depth stop 1
ETorsion spring assembly 1
FLine guide wheel 1
GLong bolt for line guide wheel 1
HEarly entry diamond wheel 1
IT25 torx bit 1
Unpacking and Checking Contents
ADE F
G
I
B
H
C
FIG. 1
-4-
Getting to Know Your Early Entry Attachment
1. Front knob
2. Front locking bolt
3. Fixed plate
4. Guide rod
5. Torsion spring assembly
6. Rear knob
7. Skid plate
8. Spring plate
FIG. 2
6
543
2
1
8 7
-5-
NOTE: Keep the original Operating/Safety in-
structions (manual) for Skilsaw SPT79A handy.
The manual for SPT79A contains additional in-
formation that is not covered in this manual. If the
SPT79A manual is missing, please download a
copy from www.skilsaw.com/service-manuals
WARNING
Disconnect the saw from the
power source before making
any assembly, adjustments or changing ac-
cessories. Such preventive safety measures
reduce the risk of starting the tool accidentally.
ATTACHING THE EARLY ENTRY
DIAMOND WHEEL
CAUTION
Use only SKILSAW early
entry diamond wheel with
this attachment. Using other wheels will lead to
unsatisfactory results and possible damage to
the tool or work area.
1. Tip the tool back with the guard facing up.
2. Press the lock button (on the back of the
saw) and turn the wheel bolt using the 1/2”
slot of the wrench (included with the saw and
stored in the foot of the saw) until the lock
button engages. The shaft is now locked.
Continue to depress button, turn wrench
clockwise and remove the wheel bolt and
OUTER WASHER (Fig. 3).
3. Make sure that the arrow on the diamond
wheel is pointing in the same direction as the
arrow on the guard.
4. Slide the diamond wheel into the guard and
mount it against the INNER WASHER on the
shaft. Be sure that the large diameter of the
INNER and OUTER washers lay flush
against the diamond wheel.
5. Reinstall the OUTER WASHER. First tighten
the wheel bolt nger tight, then tighten the
wheel bolt 1/8 turn (45˚) with the wrench pro-
vided. Do not use wrenches with longer han-
dles, since it may lead to over tightening of
the wheel bolt.
NOTE: Install a new skid plate every time a new
early entry diamond wheel is installed. SKILSAW
set SPT5008-EA includes 1 (one) replacement
wheel and 1 (one) replacement skid plate.
Direction of
rotation arrow
Diamond wheel
OUTER WASHER
Large diameterfaces
the wheel
Wheel bolt
Lock button
Wrench
INNER WASHER
Large diameterfaces
the wheel
Shaft
Guard
Assembly
FIG. 3
-6-
Assembly
ATTACHING THE LINE GUIDE WHEEL
1. Set the saw on its side on a at surface with
the blade guard facing up.
2. Loosen the locking bolt from the rear left
wheel by using T25 torx bit and an optional
screwdriver (Fig. 4a).
3. Remove the rear left wheel and its locking
bolt.
NOTE: Keep the original locking bolt in a safe
place in case the saw needs to be reverted back
to its original conguration.
4. Attach the line guide wheel, the rear left
wheel and the long bolt in the order shown
(Fig. 4b).
NOTE: The side of the rear left wheel with “SKIL-
SAW" logo should be facing out.
5. Start tightening the long bolt by hand, then
tighten 1/2 turn using T25 torx bit.
FIG. 4a
FIG. 4b
Long bolt Rear left wheel
Line guide
wheel
Long bolt
Original bolt
-7-
a
b
c
d
Middle control knob Lower control knob
FIG. 5a
FIG. 5b
ATTACHING THE TORSION SPRING
ASSEMBLY
1. Unfold the handle:
a. Press the middle control knob (Fig. 5a).
b. Unfold the upper part of the handle 180°
as shown in Fig. 5a until it audibly locks in
place.
c. Press the lower control knob (Fig. 5a)
d. Unfold the lower part of the handle as
shown in Fig. 5a until it audibly locks in place.
e. The saw should look as shown in Fig. 5b.
Assembly
-8-
Screw for calibrated
depth bracket
Wrench
Torsion spring
assembly
2. Set the saw on its side on a at surface with
the guard facing up.
3. Using T25 torx bit, remove the screw from
the calibrated depth bracket and keep it in a
safe place in case the saw needs to be re-
verted back to its original conguration (Fig.
6a).
4. Insert the torsion spring assembly as shown
in Fig. 6b.
a. The threaded end, with blue thread locker
painted on, should be inserted into the open-
ing in the calibrated depth bracket.
b. Keep proper orientation of the ends of the
torsion springs: the short end must be touch-
ing the foot of the saw.
5. Tighten the torsion spring assembly by using
the wrench provided with the saw (Fig. 6c).
Assembly
FIG. 6a
FIG. 6b
FIG. 6c
Short end
Long end
Blue thread locker
Long end
-9-
ATTACHING THE EARLY ENTRY
ATTACHMENT
1. Set the saw on its side on a at surface with
the blade guard facing up.
2. Attaching rear part.
Align the rear knob of the early entry attach-
ment with the stud of the torsion spring as-
sembly, then tighten the rear knob. The
below points need to be observed (Fig. 7):
• Ensure that the long end of the torsion spring
is inserted into the opening of the block.
• Ensure that the end of the stud is ush with
the stepped inner surface of rear knob.
Assembly
FIG. 7
End of the
stud
Stepped
inner surface
Ensure that the long end of the
torsion spring is inserted into the
opening of the block.
Block
-10-
Front
locking bolt
Wave washer
Sealing ring
ATTACHING THE FRONT PART
• Ensure that the wave washer and the sealing
ring are properly seated on the front locking
bolt (Fig. 8a).
• Thread the front locking bolt into the opening
of the front knob on the early entry attach-
ment (Fig. 8c).
• Align the front locking bolt with its mounting
opening in the saw and rst tighten the bolt
by hand, then further tighten 1/2 turn using
T25 torx bit (Fig.8b). Do not overtighten.
Assembly
FIG. 8a
FIG. 8b
FIG. 8c
Front
locking
bolt
Front knob
Mounting
opening
Tabla de contenidos
Idiomas:
Otros manuales de Sierra de skilsaw
skilsaw
skilsaw SPT70WM Instrucciones de montaje
skilsaw
skilsaw SPT70WT Instrucciones de montaje
skilsaw
skilsaw SPT88 Instrucciones de montaje
skilsaw
skilsaw SPT44A Instrucciones de montaje
skilsaw
skilsaw SPT78W Instrucciones de montaje
skilsaw
skilsaw SPT79 Instrucciones de montaje
skilsaw
skilsaw SPT67WE Instrucciones de montaje
skilsaw
skilsaw SPT99T Instrucciones de montaje
skilsaw
skilsaw SPTH70M Guía rápida
skilsaw
skilsaw SPT64MTA Instrucciones de montaje
skilsaw
skilsaw SPTH77M Instrucciones de montaje
skilsaw
skilsaw SPT78MMC Manual de usuario
skilsaw
skilsaw SPT62MTC Instrucciones de montaje
skilsaw
skilsaw SPT67M8 Instrucciones de montaje
skilsaw
skilsaw SPT70WM-01 Instrucciones de montaje
skilsaw
skilsaw SPT67FMD Instrucciones de montaje
skilsaw
skilsaw SPT44A Instrucciones de montaje
skilsaw
skilsaw SPT70WM Manual de usuario
skilsaw
skilsaw 77 Manual de usuario
skilsaw
skilsaw SPT44 Instrucciones de montaje
