Sitten BT850A Manual de operación y mantenimiento

80MM THERMAL RECEIPT

PRINTER

PROGRAMMER MANUAL

Format Description :

The programming manual command description includes the following sections:

1）[Name]

This is the first part of the command descriptions. ASCII code is given command of the form

and the function overview of command .

2）[Format]

This section uses the ASCII coding form, Hex code form, Decimal code form of three kinds of

formal description of the command. Which part of the range compared to a decimal number no

special instructions, such as in the following example 1 ≤ n ≤ 4, where 1 is a decimal number,

rather than the ASCII code table in "1".

3）[Range]Gives the allowable ranges for the arguments.

4）[Description]Describes the command’s function.

5）[Detail]

The command notice is given. Because commands in different modes, when with different

commands, will lead to mutual influence, and this section gives the details.

6）[Reference]Gives the lists of related commands.

---> ESC SP n :Transmit real-time status

---> [Format] ASCII: ESC SP n

Hex: 1B 20 n

Decimal: 27 32 n

---> [Range] 0 ≤ n≤255

---> [Description] Transmitted in real time specified by the parameter “n” Printer Status：

---> [Detail] •Immediatelyreturns the printer associated status after receiving the command.

---> [Reference]

[Name] Horizontal tab

[Format]ASCII HT

Hex 09

Decimal 09

[Decription] Moves the print position to the next horizontal tab position.

[Details]

•This command is ignored unless the next horizontal tab position has been set.

• If the next horizontal tab position exceeds the printing area,

the printer setstheprinting position to [Printing area width + 1].

• Horizontal tab positions are set with ESC D.

• If this command is received when the printing position is at [printing area width

+ 1], the printer executes print buffer-full printing of the current line and

horizontal tab processing from the beginning of the next line.

[Reference]ESCD

LF [Name] Print and line feed

[Format] ASCII LF

Hex 0A

Decimal 10

[Description] Prints the data in the print buffer and feeds one line based on the current linespacing.

[Note] This command sets the print position to the beginning of the line.

[Reference] ESC2，ESC3

DLEDC4nmt

[Name] Real-time pulse generator

[Format] ASCII DLE

DC4

Hex 10 14 n m t

Decimal 16 20 n m t

[Range] n=1,m=0,1

≤

≤8

[Decription] Output pulse is specified by the parameter t connection pins, “m” show as below：

Connect Pins

Cash Drawer Connect Pin 2

Cash Drawer Connect Pin 5

Pulse high time for[t*100 ms]，low time for [t*100

ms]

。

[Details]• When the printer is executing a command to open the cash drawer (ESCp or DELDC4),

the command is ignored.

• In serial mode, the printer immediately after receiving the order.

• In parallel mode, the printer is busy when the command is not executed.

• If the print data same as the command contains data, the data will be used as the command

is executed. The user must take into account this situation.

• Don’t try to insert the command in two or more bytes in the command sequence.

• Even if the printer is set to disabled by the command of ESC = (select peripheral), the

order is still valid.

[Reference] ESCp

ESCSPn

[Name] Setting the right side character spacing

[Format] ASCIIESC SP n

Hex1B 20 n

Decimal 27 32 n

[Range] 0≤n≤255

[Description]Setting the right side character spacing for [n¬0.125 mm].

[Note]• For the double-width mode, the right side character spacing is double than the normal

mode. When the character is magnified , the right side character spacing is n times

than the normalmode.

•This command does not affect the setting of Hanzi characters.

• The command to set the value of independent standard mode in each mode.

[Defaults] n=0

ESC!n

[Name]

Select print

mode(s)

[Format]

SCIIESC

Hex 1B 21 n

Decimal

27 33 n

[Range]0≤ n≤ 255

[Description]Selects print mode(s) ,using n as follows:

Bit

OFF/ON

Hex

Decimal

Functions

OFF

00 0

Character font

(12

24)

。

01 1Character fontB

17)

。

1---

N/A

2---

N/A

OFF

00 0

Emphasized mode not selected.

08 8

Emphasized mode selected.

OFF

00 0

Double-height mode not selected.

10 16

Double-height mode selected.

OFF

00 0

Double-width mode not selected.

20 32

Double-width mode selected.

6---

N/A

OFF

00 0

Underline mode not selected.

80 128

Underline mode selected.

[Note]• When both double-height and double-width modes are selected,

quadruple sizecharacters are printed.

• The printer can underline all characters, but can not underline the space set by

HT or 90° clockwise rotated characters.

•

The thickness of the underline is that selected by ESC , regardless of the

character size.

• When some characters in a line are double or more height, all the characters

on the line are aligned at the baseline.

• ESC E can also turn on or off emphasized mode. However, the setting of the

last received command is effective.

• ESC —can also turn on or off underline mode. However, the setting of the last

received command is effective

•GS ! can also select character size. However, the setting of the last received

command is effective.

• Emphasized mode is effective for alphanumeric and Hanzi. All print modes

except emphasized mode is effective only for alphanumeric.

[Defaults] n=0

[Reference] ESC-,ESCE,GS !

ESC$nLnH

[Name] Set absolute print position

[Format] ASCIIESC $ nL nH

Hex1B 24 nL nH

Decimal27 36 nL nH

[Range]0≤ nL≤ 255

0≤ nH

≤

255

[Description]Sets the distance from the beginning of the line to the position at

whichsubsequent characters are to be printed.

•

The distance from the beginning of the line to the print position is

[( nL + nH * 256) *(vertical or horizontal motion unit)] inches.

[Note] • Settings outside the specified printable area are ignored.

• In standard mode, the horizontal motion unit ( x) is used.

[Reference] ESC\, GS $, GS \

ESC%n

[Name]Select/cancel user-defined character set

[Format] ASCIIESC % n

Hex 1B 25 n

Decimal 27 37 n

[Range] 0≤ n≤ 255

[Description]Selects or cancels the user-defined character set.

• When the LSB of n is 0, the user-defined character set is canceled.

•When the LSB of n is 1, the user-defined character set is selected.

[Note]When the user-defined character set is canceled,the internal character set is

automatically selected

• n is available only for the least significant bit.

[Defaults] n=0

[Reference] ESC&,ESC?

ESC&yc1c2[x1d1...d(y×x1)].. .[xkd1...d(y×xk)]

[Name] Define user-defined characters

[Format] ASCII ESC & y c1 c2[x1d1...d(y  x1)]...[xkd1...d(y

  xk)]

Hex 1B 26 yc1 c2[x1d1...d(y  x1)]...[xkd1...d(y

  xk)]

Decimal 27 38 yc1

c2[x1d1...d(y

 

x1)]...[xk

d1...d(y

  xk)]

[Range] y=3

32 ≤ c1≤ c2≤ 126

0≤ x≤ 12(12×24)

0≤ x≤ 9(9×17)

0≤ d1...d(y× xk)≤ 255

[Description]Defines user-definedcharacters.

•y specifies the number of bytes in the vertical direction.

• c1 specifies the beginning character code for the definition, and c2 specifies the

final code

• x specifies the number of dots in the horizontal direction.

[Note]• The allowable character code range is from ASCII code <20>H to <7E>H (95characters).

•

It is possible to define multiple characters for consecutive character codes.

If only one character is desired, use c1 = c2.

• d is the dot data for the characters. The dot pattern is in the horizontal directionfrom the

left side. Any remaining dots on the right side are blank.

• The data to define a user-defined character is(y×x)bytes.

• Set a corresponding bit to 1 to print a dot or 0 to not print a dot.

•

This command can define different user-defined character patterns by each

fonts. To select a font, use ESC !

• A user-defined character and a downloaded bit image cannot be defined

simultaneously. When this command is executed, the downloaded bit image is

cleared.

• The user-defined character definition is cleared when:：

1) ESC @ is executed.

2) ESC ? is executed.

3) ESC? is executed

4) The printer is reset or the power is turned off.

• When the user-defined characters are defined in font B (9 ╳17),only the

mostsignificant bit of the 3rd byte of data in vertical direction is effective.

[Defaults] The internal character set

[Reference] ESC%,ESC?

[Example]

•

When font A

(12*24)is selected.

•

When font B

17)

is selected.

d1=<0F>Hd4=<30>Hd7=<40>H...

d2=<03>Hd5=<80>Hd8=<40>H...

=<00>Hd6=<00>Hd9=<20>H...

d1=<1F>Hd4= <08>Hd7=<10>H...

d2=<FF>Hd5= <08>Hd8=<04>H...

d3=<80>Hd6=<00>Hd9 =<00>H...

ESC*mnLnHd1...dk

[Name] Select bit-image mode

[Format]ASCIIESC

∗

d1...dk

Hex

2A m nL nH d1...dk

Decima l

42 m nL nH d1...dk

[Range]m=0, 1, 32,33

0≤ nL≤ 255

0≤nH≤ 3

0≤ d≤ 255

[Description]Selects a bit-image mode using m for the number of dots specified by nL and nH,as follows:

Mode

Vertical Direction

Horizontal Direction

Number of

Dots

DotDensity

Number of Data(K)

08-dot single-density 867.7dpi 101.6dpi nL +nH

∗

256

18-dot double-density 867.7dpi 203.2dpi nL +nH

∗

256

32 24-dot single-density 24 203.2dpi 101.6dpi (nL+

∗

256)

∗

33 24-dot double-density 24 203.2dpi 203.2dpi

(

+nH

∗

256)

∗

dpi:Print dots per 25.4 mm (1inch)

[Note]

•

If the values of m is out of the specified range, nL and data following are processed

as normal data.

nL and nH represents the horizontal upper figure points, calculated by nL + nH256 points.

•If the bit-image data input exceeds the number of dots to be printed on a line,the

excess data is ignored.

•d indicates the bit-image data. Set a corresponding bit to 1 to print a dot or to 0to

not print a dot.

•If the width of the printing area set by GS L and GS W less than the widthrequired

by the data sent with the ESC * command, the following will beperformed on the line

in question (but the printing cannot exceed the maximumprintable area):

①The width of the printing area is extended to the right to accommodate theamount

of data.

②If step ①does not provide sufficient width for the data, the left margin isreduced

to accommodate the data.For each bit in the single density mode (m = 0, 32) of the

data, the printer prints two points: For double density mode (m = 1,33) of each bit of

data, the printer prints a dot . When calculating the amount of data that can be printed

on one line, they must be considered.

• After printing a bit image, the printer returns to normal data processing mode.

• This command is not affected by print modes (emphasized, double-

strike,underline, character size or white/black reverse printing), except upside-

downprinting mode.

•The relationship between the image data and the dots to be printed is as

follows:

• When 8-dot bit image is selected:

•When 24-dot bit image is selected:

ESC- n

[Name]

Turn underline

mode on/off

[Format]

ASCII ESC

Hex 1B 2D

Decimal 27 45

[Range]0≤ n≤ 2,48≤ n≤ 50

[Description]Turns underline mode on or off, based on the following values of n:

Function

0, 48

Turns off underline mode

1, 49

Turns on underline mode (1-dot thick)

2, 50

Turns on underline mode (2-dots thick)

[Note]• The printer can underline all characters (including right-side character spacing),

but cannot underline the space set by HT.

•The printer cannot underline 90° clockwise rotated characters and

white/blackinverted characters.

• When underline mode id turned off bysetting the value of n to 0 or 48,

thefollowing data is not underlined, and the underline thickness set before

themode is turned off does not change. The default underline thickness is

1 dot.

•Changing the character size does not affect the current underline thickness.

• Underline mode can also be turned on or off by using ESC !. Note,

however,that the last received command is effective.

[Defaults] n=0

[Reference] ESC!

Tabla de contenidos

Otros manuales de Impresora de Sitten

Sitten

Sitten FTP-80C Manual de usuario

Manuales populares de Impresora de otras marcas

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series Manual de usuario

Evolis

Evolis Elypso Manual de usuario

Kyocera

Kyocera FS-9530DN Manual de usuario

Canon

Canon LASER SHOT LBP-1210 Manual de usuario

Samsung

Samsung BIXOLON SRP-350plusF Manual de usuario

Canon

Canon PIXMA PRO-1 Series Manual de usuario

Canon

Canon PIXMA G3560 Guía de configuración

Dell

Dell Color Laser Printer 2130cn Manual de usuario

Tektronix

Tektronix Phaser 840 Manual de usuario

Epson

Epson ET-7750 Instrucciones de funcionamiento

Canon

Canon CLBR 460ps Manual de usuario

Eltron

Eltron P210 Guide Manual de usuario

Ricoh

Ricoh MD-P1 Manual de usuario

Epson

Epson SC-F7100 series Manual de usuario

Epson

Epson Stylus C40UX Manual de usuario

Canon

Canon imagePASS-A2 Manual de usuario

Canon

Canon S820D Manual de usuario