SIRCHIE FPT-Series Manual

TI02-134ENG-REV4

SIRCHIE®

100 HUNTER PLACE, YOUNGSVILLE, NC 27596 USA

Ph: (919) 554-2244, (800) 356-7311 • Fax: (919) 554-2266, (800) 899-8181 • Web: www.sirchie.com • Email: [email protected]

Products • Vehicles • training

1 of 8

TECHNICAL INFORMATION

Fingerprint Bench Assembly

Catalog Nos. FPT-Series and PFT-Series (all inclusive)

INTRODUCTION

Use these instructions for assembly of all SIRCHIE ngerprint

benches.  Inspect all cartons for damage. If damage is found,

contact the delivery carrier immediately.

Carefully unpack the carton(s) and check for all parts against the list

at the end of these instructions to insure that you have everything

needed for assembly. If a part is found to be missing, please contact

the factory for prompt service. Assembly should be done on a clean,

soft cloth or other nonabrasive surface.

PROCEDURE

For All Bench Assemblies

1. Assemble divider insert to center divider with four 6-32 x 1/4"

pan head screws (Fig. 1). FIGURE 1

SFL1009

Divider Insert

SFL1008

Center

Divider

SFL225

TI02-134ENG-REV4

2 of 8

3 of 8

2. Assemble center divider as-

sembly to bottom with three

6-32 x 1/4" pan head screws

(Fig. 2).

3. Lay the top upside down on

the work surface. Attach the

end caps with two 6-32 x

3/8" black pan head screws,

#6 washers and 6-32 hex

nuts. Slide the two end pan-

els in place on the assembled

bottom. Set this entire bottom

assembly onto the studs pro-

truding from the top. Secure

with eight #6 lock washers

and 6-32 hex nuts (Fig. 3).

For Table Model Benches

(FPT274A, FPT274PIP,

FPT275A, FPT275APIP,

PFT100A, PFT100APF, PFT100ACM, PFT200A, PFT200APF, PFT200ACM)

4a. With the unit upside down, secure the end panels to the back with six 6-32 x 1/4" pan head screws.

Secure the end panels to the bottom with four 6-32 x 5/8" pan head screws. Attach the rear feet with

two 6-32 x 5/8" pan head screws. Attach the front feet with two #6 x 5/8" sheet metal screws. The

unit is now ready for use (Fig. 4a).  Optional wall mount conguration also shown.

FIGURE 2

SFL1008

Center

Divider

SFL225

SFL1006

Bottom

SFL1007

Back

2 of 8

TI02-134ENG-REV4

3 of 8

For Column Mount Benches

(FPT400S, FPT400SPIP, FPT500S, FPT500SPIP, FPT200P, FPT200PPF, FPT200PCM, FPT300P,

FPT300PPF, FPT300PCM)

 The column must be assembled prior to the next step. Refer to the bench pedestal assembly in-

structions on Page 5.

Assembled

Bottom

SFL121

SFL118

SFL1011

End/Right

SFL1010

End/Left

Top

Subassembly

SFL100

End Cap SFL1001

SFL1001

SFL1006

FIGURE 3

TI02-134ENG-REV4

4 of 8

5 of 8

4b. Place the unit in an upright position. Secure the end panels to the back with 6-32 x 1/4" pan head

screws and tighten. Place the assembled column on a level surface. Place the bench on top of the

column with the front of the bench facing the tabs on the column top. Secure the bench to the column

using four 6-32 x 3/8" pan head screws. Secure the end panel to the bottom with two 6-32 x 1/4" pan

head screws. Your unit is now ready for use (Fig. 4b).

SFL225

SFL225 SFL225

SFL1002

SFL1000

SFL2091

Assembled

Bench

FIGURE 4a

SFL2146

Wall Mount

Option

FIGURE 4b

Assembled

Bench

SFL225

SFL115

Assembled

Column

*When ordering a Top Subassembly, you MUST include the Model Number

of your ngerprint bench.

4 of 8

TI02-134ENG-REV4

5 of 8

BENCH PEDESTAL ASSEMBLY INSTRUCTIONS

Check for damage upon receipt of Fingerprint Bench Pedestal and report any to delivering carrier.

Open all boxes and carefully remove contents. Check against list on back page for all necessary parts to

construct the base. If any parts are missing, contact the factory for prompt service.

1. Carefully unwrap all parts and hardware. Be

sure to work on a piece of carpet, cloth or other

nonabrasive surface.

2. Place the base face-up on the work surface.

Screw the two (2) threaded rods into the base

so that they protrude through the bottom about

1/2" (13mm). Place the column over the thread-

ed rods (Fig. A).

3. Place the mounting plate on top of the column

so the threaded rods protrude through the two

(2) holes in the plate. Insert a lock washer and

an acorn nut on each rod and tighten. Continue

to tighten the acorn nuts which in turn tightens

the rods into the base until entire assembly is

sturdy (Fig. B).

4. Turn the column assembly upside down. Place

a lock washer and hex nut on the threaded

rods and tighten (Fig. C). Return the assembly

upright. Your base is ready to accept the nger-

print bench. FIGURE A—Place column over threaded rod.

TI02-134ENG-REV4

6 of 8

7 of 8

FIGURE B—Attach mounting plate to column.

FIGURE C—Secure rods through bottom of base.

6 of 8

TI02-134ENG-REV4

7 of 8

FPT274A, FPT274PIP, FPT275A,

FPT275APIP, PFT100A, PFT100APF,

PFT100ACM, PFT200A, PFT200APF,

PFT200ACM CONTENTS:

1-SFL?TopSub-Assembly*

1-SFL1006Bottom

1-SFL1007Back

1-SFL1008CenterDivider

1-SFL1009DividerInsert

1-SFL1010EndPanel,left

1-SFL1011EndPanel,right

2-SFL1005EndCaps

4-SFL1000RubberFeet

20-SFL2256-32x1/4"PanHead

Screws

4-SFL10016-32x1/4"PanHead

Screws(black)

2-SFL10026-32x5/8"PanHead

Screws

2-SFL2091#6x5/8"SheetMetal

Screws

12-SFL118#6InternalStarLock

Washer

12-SFL1216-32HexNuts

FPT400S, FPT400SPIP, FPT500S,

FPT500SPIP, FPT200P, FPT200PPF,

FPT200PCM, FPT300P, FPT300PPF,

FPT300PCM CONTENTS:

1-SFL?TopSub-Assembly*

1-SFL1006Bottom

1-SFL1007Back

1-SFL1008CenterDivider

1-SFL1009DividerInsert

1-SFL1010EndPanel,left

1-SFL1011EndPanel,right

2-SFL1005EndCaps

18-SFL2256-32x1/4"PanHead

Screws

2-SFL2146WallMountBrackets

4-SFL1156-32x3/8"PanHead

Screws

4-SFL10016-32x1/4"PanHead

Screws(black)

12-SFL118#6InternalStarLock

Washer

12-SFL1216-32HexNuts

BENCH PEDESTAL CONTENTS:

1-SFL136Base

1-SFL828Column

1-SFL2160ColumnMount

2-SFL829ThreadedRods

4-SFL1763/8"LockWasher

2-SFL1743/8"-16HexNut

2-SFL1733/8"-16AcornNut

4-SFL10016-32x3/8PanHead

PhilipsMachineScrews(black)

*When ordering a Top Subassembly, you MUST include the Model Number of your fingerprint bench.

TI02-134ENG-REV4

8 of 8

SIRCHIE®

PRODUCTS • VEHICLES • TRAINING

100 Hunter Place, Youngsville, nc 27596 usa

919-554-2244 • 800-356-7311

www.sirchie.com

Este manual sirve para los siguientes modelos

Manuales populares de Almacenamiento de herramientas de otras marcas

Ryobi

Ryobi RWB03 Manual de usuario

Husky

Husky H27CH5TR4BGK Manual de usuario

Scheppach

Scheppach ts 2100 Manual de usuario

Cornwell Tools

Cornwell Tools CTB360AKBK Manual de usuario

DIVERSIFIED WOODCRAFTS

DIVERSIFIED WOODCRAFTS SHAIN GSB-6024 Manual de usuario

Cassese

Cassese CS200 CART Manual de usuario

Kendall Howard

Kendall Howard ESDW-9630-1000 Manual de usuario

Lista

Lista Align Instrucciones de montaje

Workzone

Workzone 99609 Manual de usuario

Stanley

Stanley STST83800-1 Manual de usuario

Homak

Homak PROFESSIONAL Series Manual del sistema

Perel

Perel ROLLER SHUTTER STORAGE CABINET Manual de usuario

Husky

Husky H5CH2R Manual de usuario

BGS technic

BGS technic 4107 Manual de usuario

Clarke

Clarke CWB1250 Manual de usuario

Ryobi

Ryobi RWB02 Manual de usuario

Husky

Husky H52CH6HDV3WHT Manual de usuario

Sealey

Sealey PTB66004 Manual de usuario