SINNOWA W600 Manual de usuario
W600
Auto Washer
（
V1.0
）
User’s Manual
Sinnowa Medical Science &Technology Co.，Ltd
INDEX
1. INTRODUCTION........................................................................................................................1
1.1 FEATURES..............................................................................................1
1.2 WORKING ENVIRONMENT REQUIREMENTS..................................................1
1.3 PERFORMANCE .......................................................................................1
1.4 INSTRUMENT STRUCTURE ........................................................................2
2. INSTALLATION...........................................................................................................................2
2.1 UNPACKING ............................................................................................2
2.2 CONNECT THE OUTER PIPE.......................................................................2
2.3 CONNECT THE POWER .............................................................................2
3. OPERATIONS .............................................................................................................................3
3.1SYSTEM SETUP .......................................................................................3
3.2 PROGRAM SETUP ....................................................................................7
3.3 WASH ..................................................................................................11
3.4 WASH PIPE ...........................................................................................14
4. WASH PROCESS OPERATION SUMMARY.............................................................15
5. ROUTINE MAINTENANCE .................................................................................................15
6. TROUBLESHOOTING...........................................................................................................16
7. TRANSPORTATION AND STORAGE...........................................................................17
7.1 TRANSPORTATION .................................................................................17
W600 Auto Washer User’s Manual
1 Introduction
W600 automatic washer is a microprocessor-controlled washer. It
can be fitted with either an 8 or 12 channel manifold which are
fitted with one aspirating and one dispensing needle per well. Up
to 50 user-defined programs can stored in the memory and recalled
by user.
This manual gives the installation and operations for the W600
Automatic Washer, it shouldbe read carefµlly in its entirety prior
to any attempt to operate the washer.
1.1 Features
Washer has the feature of simple structure, stable working
condition, and low maintenance cost. Chinese / English version is
free to switch for users.
1.2 Working environment requirements
Power requirements
110/220 V ± 10
%
,50/60Hz ± 2
%
Fuse
T1AL250V
Power consumption
100VA
Operation temperature
10°C to 40°C
Relative humidity
No more than 75 percent
Atmospheric pressure
86.0kPa ~ 106.0kPa
Other requirement
Avoid dust, strong
electromagnetic interference and
corrosive gases
Avoid mechanical vibration
Good grounding of network power
supply
1.3 Performance
Washing strips
1-12
Washing cycle
1-99
Washing scope of application
96-well plate, 48-well plate and
single plate
Residual volume
< 2uL per well
programs storage
50 stored programs
Washing capacity
50-500µl, optional setting(step
length is 50µl)
Soake time:
0-3600 seconds
plate-type options
U plate, flat plate, V plate
Shake time
1-99 seconds
1
W600 Auto Washer User’s Manual
1.4 Instrument structure
Washer is content of control system, movement system, pump,valve,
washing manifold and carrier home.
2 Installation
2.1 Unpacking
(1) Lift the unit from the box by holding the unit.
(2) Remove the accessories from the unit.
(3) Verify that all items on the packing list have been received.
(4) Inspect all components for shipneedleg damage. In case of
damage, contact the shipper who delivered your equipment.
(5)Save all packing material in case it becomes necessary to return
the unit.
(6)Put the instrument on a flat level platform.
2.2 Connect the outer pipe
Six pieces of silicon rubber tubes is used to connect the unit with
the outer bottles,please connect them according to apellation. Cut
off the belts on the washing manifold after the outer pipe has been
well connected.
2.3 Connect the power
Connect the power cable to the unit, switch on the power, the washer
begins self-initialize, after a few minutes the LCD will display：
Then the washer is ready to use. Press Enter key to come into main
menu ：
W600Auto Washer
Wash
Program setup
System setup
Wash pipe
W600Auto Washer
SINNOWA
2
W600 Auto Washer User’s Manual
3. Operations
3.1 System setup
It is recommendable that you should check and adjust the position
parameter before you begin to use the washer in order to get the
good washing effect.
Press
to choose “System setup”.
Press Enter key to come into “System setup”.
Input six “
”.
Press Enter to confirm.
W600Auto Washer
Wash
Program setup
System setup
Clean pipe
System setup
Please input password:
System setup
Please input password:
*******
System setup
Language setup
Position setting
Title setup
3
W600 Auto Washer User’s Manual
Press Enter key to come into “Language setting”.
Press
to choose language.
Press
to choose language.
Press
to choose “Position Setting”.
Press Enter key to come into “Position Setting”.
Press
key to adjust long needle to reach the bottom of
trough.
Press
to move the carrier to the left or right to adjust
long needle to the center of first strip micro-wells ,and as
following shown:
Language setup
中文
English
System setup
Language setup
Position setting
Title setup
Position setting
Long pin in the center of first
strip micro-well
micro-well left
right
Please press “Entre” to sure
Position setting
Long needle to
the bottom of
trough
needle up
down
Please press “Entre” to sure
4
W600 Auto Washer User’s Manual
Press Enter key to confirm.
For flat micro-well, this is the first point of the manifold
aspiration needle when use two-point aspiration. Press
to
move the carrier to the left or right, the best position should
be close to the left wall of the micro-well.Adjusted position is
as shown below.
Press Enter key to confirm.
Position setting
Long needle on the left
of
micro-well
micro-well left
right
Please press “Entre” to sure
Position setting
Long needle on the right
of
micro-well
micro-well left
right
Please press “Entre” to sure
5
W600 Auto Washer User’s Manual
For flat micro-well, this is the second aspirating point in
two-point aspiration process. Press
to tune up long probe
position. Adjusted position is as shown below.
Attention: When adjust long needle to the left or right of first
strip micro-wells, the position should not too close to or too far
away with wall according to washing effect.
Press Enter key to confirm.
Press
to move the washing manifold so that long needle to
reach the bottom of micro-well, the best position is the position
that the long needle be closest to the bottom of the
micro-well.Adjusted position is as shown below.
Press Enter key to confirm.
Position setting
Long needle to the
bottom of
micro-well
needle up ,
down
Please press “Entre” to sure
Position setting
Long needle at the upside of
micro-well
needle up ,
down
Please press “Entre” to sure
6
Tabla de contenidos
