Singer XL-420 Manual de usuario

Service Manual

Original issue

May 2014

Page 1／64

Model

XL-420

| 1

XL-420

First issue: May, 2014

Service Manual

Original issue

May 2014

Page 2／64

Model

XL-420

| 2

SEC.1 Disassembling covers

SEC.2 Test mode with warning function deactivated

SEC.3 Needle clearance to shuttle

SEC.4 Alignment of needle plate to shuttle

SEC.5 Presser foot height and direction

SEC.6 Origin point positioning of zigzag bight

SEC.7 Needle bar height

SEC.8 Needle threader height

SEC.9 Adjustment of feed dog height

SEC.10 Tension of timing belt

SEC.11 Needle timing to feed dog

SEC.12 Needle timing to shuttle hook

SEC.13 Adjustment of timing of take-up lever to shuttle

SEC.14 Adjustment of meshing position of gears for take-up lever

SEC.15 Retaining bracket for bobbin case

SEC.16 Origin point positioning of feed “zero”

SEC.17 Stitch length

SEC.18 Ajustment of upper thread tension

SEC.19 Adjustment of CAM sensor

SEC.20 Check the Knee Lifter

SEC.21 Sewing machine test mode

SEC.22 Removing top cover and carriage cover of embroidery unit

SEC.23 Adjustment of stop position of embroidery carriage

along X & Y axis

SEC.24 Embroidery unit test mode

SEC.25 Trouble contents with LED on panel

SEC.26 Wiring diagram part1 & part2

SEC.27 Main circuit board and functions of each connector

Contents

Service Manual

Original issue

May 2014

Page 3／64

Model

XL-420

| 3

Ａ．Disassembling face cover

Ｂ．Disassembling bed cover

1. Pull out cap (not shown) in the center

and remove screw.

2. Loosen the screw behind.

3. Remove face cover

1. Pull out cap at bed cover using needle.

SEC.1-1 Disassemblin

covers

(

)

Service Manual

Original issue

May 2014

Page 4／64

Model

XL-420

| 4

Ｃ．Disassembling bobbin winder unit.

2. Loosen M4 screw.

3. Slide out bed cover.

1. Remove M3 screw at bobbin winding

latch.

2. Remove bobbin winding latch.

SEC.1-2 Disassembling covers (2)

Service Manual

Original issue

May 2014

Page 5／64

Model

XL-420

| 5

Ｄ．Removing switch cover

3. Remove M4 screw at bobbin winder

cover.

4. Remove two hooks at the side of the cover

from rear cover.

１．Removing M4 screws at the side of the cover.

SEC.1-3 Disassembling covers (3)

Service Manual

Original issue

May 2014

Page 6／64

Model

XL-420

| 6

Ｅ．Removing base cover

２．Remove switch cover.

１．Remove three M4 screws behind the sewing machine.

２．Lay the machine and remove two M3 tapping screws.

SEC.1-4 Disassembling covers (4)

Service Manual

Original issue

May 2014

Page 7／64

Model

XL-420

| 7

Ｆ．Remove front and rear covers.

３．Remove two M4 screws on the right.

４．Remove two M4 screws on the center.

1. Remove two M4 tapping screws near the handle at the top of rear

cover.

SEC.1-5 Disassembling covers (5)

Service Manual

Original issue

May 2014

Page 8／64

Model

XL-420

| 8

４． Lay the machine and open a rid behind the front cover by using a

small screw driver.

3. Remove M3 screw and washer at the front cover.

You can only loosen a screw but if you do so, be careful of a

position of washer when re-assembling.

2. Remove M4 screw at rear cover.

SEC.1-6 Disassembling covers (6)

Service Manual

Original issue

May 2014

Page 9／64

Model

XL-420

| 9

5. Insert small screw driver into clearance

between front and rear covers and then lift up the

front cover to remove two covers as shown at left.

* Once hooked portions A, B and C as shown

above are removed, other mating portions may be

removed easily.

ＡＢ

Ｃ

6. Lay the machine on its back for easier removal

of covers. Remove front cover. Remove CPU

board and FFC-28 from front cover with care.

*FFC is flexible flat cable

SEC.1-7 Disassembling covers (7)

Ｂ

Ｃ

Service Manual

Original issue

May 2014

Page 10／64

Model

XL-420

| 10

7. Lower the presser foot lever and

then remove rear cover by lifting up

and passing it under the presser foot

taking care not to interfere with each

other.

This is a view of machine without front

cover.

This is a view of machine without

rear cover.

SEC.1-8 Disassemblin

covers

(

)

Otros manuales para XL-420

Otros manuales de Máquina de coser de Singer

Singer

Singer 45W Guía de inicio rápido

Singer

Singer 2282 Manual de usuario

Singer

Singer 2010 Manual de usuario

Singer

Singer QUANTUM 9910 Manual de usuario

Singer

Singer 569U2100A Series Guía de configuración

Singer

Singer C7200 Manual de usuario

Singer

Singer 211W146 Manual de usuario

Singer

Singer 247-2 Manual de usuario

Singer

Singer C5200 Manual de usuario

Singer

Singer 246-31 Manual de usuario

Singer

Singer 3337 Manual de usuario

Singer

Singer 247-1 Manual de usuario

Singer

Singer 143G2 Guía de inicio rápido

Singer

Singer Quantum XL-1 Manual de usuario

Singer

Singer 457A Manual de usuario

Singer

Singer 147-82 Manual de usuario

Singer

Singer 14T968DC Professional 5 Manual de usuario

Singer

Singer 522D Manual de usuario

Singer

Singer Merritt 8834 Manual de usuario

Singer

Singer Futura CE-200E Manual de usuario

Singer

Singer 7110 Manual de usuario

Singer

Singer H74 Manual de usuario

Singer

Singer 14U 234B Manual de usuario

Singer

Singer Stylist II Serger Manual de usuario

Manuales populares de Máquina de coser de otras marcas

Riccar

Riccar RL634DE Manual de usuario

Pfaff

Pfaff 3307-1 SERIES Manual de usuario

Janome

Janome Quilt Maker Pro 18 VERSA Manual de usuario

Siruba

Siruba C007JP Manual de usuario

Husqvarna Viking

Husqvarna Viking Designer SE Manual de usuario

IKEA

IKEA SY Manual de usuario

Pfaff

Pfaff 571 Manual de usuario

Brother

Brother BB370 Manual de usuario

Pegasus

Pegasus WT100 Series Manual de usuario

Reliable

Reliable 7100DB Manual de usuario

Pfaff

Pfaff 937 Manual de usuario

Pfaff

Pfaff 1471 E1 Manual de usuario

Kenmore

Kenmore 16677 - Serger Sewing Machine Manual de usuario

HIGHLEAD

HIGHLEAD GC2008-M Manual de usuario

Brother

Brother BE-1204C Manual de usuario

JUKI

JUKI MO-104 Manual de usuario

Bernina

Bernina Quilting Frame Manual de usuario

Brother

Brother 885-V14 Manual de usuario