Sindoh D310 Series Manual de usuario
D310 Series
Quick Installation Guide
2
Device Installation Procedure
Important
- Be sure to correctly follow the procedures in order as explained in this Installation Manual.
If you do not follow the procedure in order, the image trouble may occur.
1. Overview of Installation Procedure
<D310 Series>
When installing the main body and associated options as a system, follow the order shown on the upper.
Warning
- Lifting the main body in an awkward position or transporting it in a poorly balanced position
could result in personal injury. When transporting the main body, assign an adequate
number of persons to the job and ensure that each person can take a good position of not
being excessively loaded. (mass: approx. 72 kg (158-3/4 lb))
Note
- For the detailed installation procedures for each option, follow the instructions given in the
corresponding installation manual and perform the procedures correctly.
- When placing the main body on the floor, make sure to use the paper feed cabinet or the desk to
secure the performance and the quality of the product.
- To use this machine, install the reverse automatic document feeder or the original cover.
- Once the Power Switch is turned ON, do not turn OFF it until the installation work has been
completed.
3
6Avoid a dusty location, or a place near
volatile and flammable substances.
7Avoid a poorly ventilated place.
4. Notes on using touch panel
Be sure to instruct users on the following points.
- Pressing the touch panel hard may cause
damage.
- Do not strongly press the panel or press it
using the sharp tip of mechanical pencils.
5. Accessory parts
No. Name Q’ty
1 User’s guide holder 1
2 Quick start guide 1
3 Installation manual 1 set
4 User’s guide CD 1
5 CD-ROM 1 set
6 Paper size label 1
7 Panel sheet 1
8 Blank label 1
9 Power cord * 1
10 Connector cover 1
11 Duct cover 1
12 Screw 1
13 Stylus pen 1
14 Waste toner box 1
15
CORE *(used for the network cable
Model Name: 28A2029-0A0
1
16 CABLE TIE* 1
* Varies depending on the applicable marketing
area.
2. Installation space (unit: mm)
D310 Series + DF-628 + PC-214 + MK-603 +
RU-14 + FS-534 + SD-511 + MK-748 + CU-101
1724
493
1216
430
646 585
660 126
528254779
1561
3. Pre-installation check items
1Select a level and stable place for installing
the machine.
2Be sure to use a power source of the voltage
and frequency indicated in the product
specifications.
Ensure that the current carrying capacity of
the power outlet is at least equal to the
current listed in the product specifications.
3Power the machine directly from a dedicated
power outlet. (Do not use an extension cord.)
4Do not plug or unplug the power cord with
wet or dirty hands, otherwise you may get an
electric shock.
5Avoid a hot and humid environment, or a
place exposed to direct sunlight.
4
* Power supply: 120V 12A, 220-240V 8A
Note
- This manual provides the illustrations of
the accessory parts and machine that may
be slightly different in shape from yours.
In that case, instead of the illustrations,
use the appearance of your machine to
follow the installation procedure.
This does not cause any significant
change or problem with the procedure.
6. Installing the main body and
the Paper Feed Cabinet (or the
Desk)
1Take the main body and the Paper Feed
Cabinet (or the Desk) out from its packaging.
Caution
-
Main body mass: approx. 72 kg
(158-3/4 lb)
Make available collective manpower of
an appropriate size for transporting the
main body.
Note
- Remove the main body, holding it by the
locations on the left side and the handles
on the right side as shown in the
illustration and keeping it level.
2Refer to the installation manual for the Paper
Feed Cabinet (or the Desk) and follow the
“Installation Procedures.”
Note
- If installing the Heater HT-509 and the
Power Supply BOX MK-734, install them
at the same time as the installation of the
Paper Feed Cabinet (or the Desk).
7. Removing protective tape,
packing and other shipping
materials
1Remove the protective tape and the
protectivematerials.
5
2Open the right door and remove the locking
materials.
Note
- After removing the locking materials,
make sure that the transfer roller assy is
secured in place.
In the case of <NG>, press the transfer
roller assy into place so that it is secured
as shown in <OK>.
- Save the locking materials removed in this
and subsequent steps of
11
and
15
for
later use when transporting the machine.
＜OK ＞ ＜ NG ＞
3Remove the protective sheet as shown in the
illustration.
4Move the fusing adjustment lever down to the
printing position (bottom).
5Close the right door.
6Remove the protective film from the control
panel.
7Slide out the tray 1.
6
8Remove the protective tape from the inside of
the tray 1 and remove accessory parts.
9Slide out the tray 2.
10
Remove the protective tape from the inside of
the tray 2 and remove accessory parts.
11
Remove the locking material at the left side
of the scanner unit.
12
Affix the supplied blank label.
13
Open the front door.
14
Remove the protective tape.
15
Remove the locking materials from the four
places.
7
16
Release the lever of the drum unit (K).
17
Slightly slide the drum unit (K) out and
remove the protective tape and protective
material.
18
Slide the drum unit (K) into the machine.
19
Lock the drum unit (K) with the lever.
20
Install the supplied waste toner box.
Note
- Push the areas indicated by the “ ”
marks to set the waste toner box to the
machine.
- Check the levers on the left and right
sides that it is securely locked.
8. Installing the toner cartridge
Note
- Since a toner cartridge is not supplied with
the machine, purchase one (of different
colors) separately.
1Shake the toner cartridge up and down and
left to right 5 to 10 times respectively.
Note
- Shake the cartridge adequately.
Otherwise, it may cause trouble.
2Insert the toner cartridge into the machine.
Note
- Make sure that the color is same between
inserting port and the toner cartridge.
- Make sure that the blue label position of
the toner cartridge is matched with the
one of the machine side.
8
3Push the toner cartridge all the way in and
rotate it clockwise to lock it.
Note
- Make sure that the toner cartridge is
pushed all the way in.
4Using the same procedure, install the toner
cartridges for other colors of toner.
5Close the front door.
9. Installing other options
To install other options, refer to the installation
manual for each option and follow the
“Installation Procedures.”
10. Mounting the accessory parts
1Set the stylus pen in the place shown in the
illustration.
2Attach the supplied connector cover to the
machine. (One supplied screw)
3Attach the supplied duct cover.
11. Connecting the power cord
1Connect the power cord.
Note
- This may not be performed depending on
the applicable marketing area.
9
2Plug the power cord into the power outlet.
12. Starting the machine
Turn ON the power switch on the right side of the
main body.
13. Date & Time Setting/Time
Zone Setting (Service Mode)
1Display the Service Mode screen.
(For details of how to display the Service
Mode screen, see the service manual.)
2Display the Date & Time Setting/Time Zone
Setting screen. (To display the Date & Time
Setting/Time Zone Setting screen, press
Stop→3onthecontrolpanel.)
3Do not input date and time but touch “Entry”
of the Date & Time Setting.
4Input the time zone using up/down keys or
direct keys.
5Touch “Entry” of the Time Zone Setting.
6Touch “Apply.”
7Touch “OK.”
8Touch “Next.”
14. Serial number input
Note
- Serial number input is, if necessary,
needed only for the optional devices
installed in “9. Installing other options.”
1Touch the item you want to enter and input
the serial number.
2Touch “END.”
3For other devices, enter their serial number in
the same way.
4Touch “END.”
5Touch “Next.”
15. Unit change
Note
- This function allows the user to select the
type of message that will appear when the
replacement time arrives for each of the
different units.
1Select the appropriate message type for each
unit.
2Touch “Service.”
16. Performing Non-Image Area
Erase Check
Note
- Perform the below at the site where
customer uses the machine.
1Select the Non-Image Area Erase Check
function as follows:
Machine→Non-ImageAreaEraseCheck.
10
2Open fully the reverse automatic document
feeder or the original cover if loaded.
Note
- Do NOT place a document on the
document glass.
- Clean the document glass if dirty.
3Press the 【】key.
4Make sure that “Result” is “OK.”
Note
- If “Result” is “NG1” or “NG2”, review the
place and direction of installation, or take
measures to block the light source (by
covering it, etc.), then perform installation
checking again. (If a fluorescent light or
other bright light sources exist right above
the machine, the light source can hinder
installation checking and cause operation
errors in the Non-Image Area Erase
Check. For detailed information, see the
service manual.)
5Touch “OK.”
17. Configuring other options
1If any of the following options are installed,
refer to the “Configuration procedures” of the
installation manual for each option and
configure the option(s).
• Reverse Automatic Document Feeder
DF-628
• Stamp Unit SP-501
• Fax Kit FK-513
• Punch Kit PK-520/PK-519
• Local Interface Kit EK-609
• Upgrade Kit UK-212/UK-211
• Paper Feed Cabinet PC-414
• Hard Disk HD-522
(Do not perform this procedure for options
already installed as standard equipment.)
• Authentication Unit AU-201S/AU-102
• Clean Unit CU-101
• Network Fax
2Exit from the Service Mode and return to the
initial screen.
18. Connecting the network cable
1Connect the main body and networking
equipment (HUB) using the network cable.
Note
- The following shows the recommended
network cables that correspond to each
communication speed.
● 10BaseT/100BaseTX: Category5
● 1000BaseT: Category 5E, Category 6
LED 2
LED 1
Networkport
Otros manuales para D310 Series
3
Tabla de contenidos
Otros manuales de Impresora de Sindoh
