Sinclair MC-D09AI Manual de usuario

USER'S MANUAL

MULTI COMBI SERIES

DUCT MC-D09,12,18,21,24AI



User Notice

◆The total capacity of the indoor units which runs at the same time can not exceed 150% of

that of the outdoor units; otherwise, the cooling (heating) effect of each indoor unit would be poor.

◆Switch the main power on 8 hours before start the unit, helpful for a successful startup.

◆It is a normal phenomenon that the indoor unit fan will still run for 20~70 seconds after the

indoor unit receives the “stop” signal so as to make full use of after-heat for the next operation.

◆ When the running modes of the indoor and outdoor units conict, it will be indicated on

the display of the wired controller in ve seconds and then the indoor unit will stop. In this case,

they can back to the normal condition by harmonizing their running modes: the cooling mode is

compatible with the dehumidifying mode and the fan mode can go with any other mode. If the

supply power fails when the unit is running, then the indoor unit will send the “start” signal to the

outdoor unit three minutes later after power recovery.

◆During installation, the communication cable and the power cord must not be twisted

together but instead separated with an interval of at least 2cm; otherwise the unit is likely to run

abnormally.

This product must not be disposed together with the domestic waste. This product

has to be disposed at an authorized place for recycling of electrical and electronic

appliances.

Thank you for purchasing Sinclair air conditioners. Before use, please read this manual

carefully and keep it properly for further reference.

Wired Controller XK19

ⅠWired Controller XK19

1 Wired Controller XK19

It is optional for the cassette type, wall-mounted, and oor ceiling indoor units.

1.1 Outside View of the Wired Controller

Fig.1 Outside View of the Wired Controller

1.2 LCD of the Wired Controller

Fig.2 LCD of the Wired Controller

Wired Controller XK19

1.3 Introduction to the Symbols on LCD

Table 1

No. Symbols Description

1Swing function.

2Sleep function (3 types: sleep 1,sleep2 and sleep 3).

3Running modes of the indoor unit (Cooling, Dry, Fan and Heating).

4Defrosting function for the outdoor unit.

5Gate-control function (this function is yet unavailable for this unit).

6Lock function.

7High, middle, low or auto fan speed of the indoor unit.

8 SHIELD Shield functions (buttons, temperature, On/Off, Mode or Save is shielded or

Save is shielded by the remote monitor.

9 TURBO Turbo function.

10 MEMORY Memory function (The indoor unit resumes the original setting state after

power failure and then power recovery).

11 MASTER Master wired controller (this function is yet unavailable for this unit).

12 It blinks under on state of the unit without operation of any button.

13 SAVE Energy-saving function.

14 Ambient/preset temperature value.

15 E-HEATER Electric auxiliary heating function.

16 BLOW Blow function.

17 Timing value.

18 QUITE Quiet function (two types: quiet and auto quiet).

19 SET It will be displayed under the debugging mode.

2 Buttons

2.1 Buttons on the Wired Controller

Fig. 3 Buttons on the Wired Controller

Wired Controller XK19

2.2 Function of the Buttons

Table 2

No. Name Function

1 Enter/cancel ① Function selection and cancellation.

② Press it for 5s to examine the outdoor ambient temperature.

2▲① Running temperature setting of the indoor unit, range:16 ～30℃ .

② Timer setting, range:0.5-24 hr.

③ Switchover between quiet/auto quiet or among sleep1/sleep2/sleep 3.

6▼

3 Fan Setting of the high/middle/low/auto fan speed.

4 Mode Setting of the Cooling/Heating/Fan/Dry mode of the indoor unit.

5 Function Switchover among the functions of Swing/Sleep/Turbo/Save/E-heater/Blow /

Quiet etc.

7 Timer Timer setting.

8 On/Off Turn on/off the indoor unit.

4+2 ▲+Mode

Press them for 5s under off state of the unit to enter/cancel the Memory function

(If memory is set, indoor unit after power failure and then power recovery will

resume the original setting state. If not, the indoor unit is defaulted to be off after

power recovery. Memory off is default before delivery.).

3 +6 Fan+▼

By pressing them at the same time under off state of the unit, will be displayed

on the wired controller for the cooling only unit, while will be displayed on

the wired controller for the cooling and heating unit.

2 +6 ▲+▼

Upon startup of the unit without malfunction or under off state of the unit,press

them at the same time for 5s to enter the lock state, in which case, any other

buttons won’t respond the press. Repress them for 5s to quit this state.

3 Operation Instructions

3.1 On/Off

Press On/Off to turn on the unit and turn it off by another press.

Note: The state shown in Fig.4 indicates the “Off” state of the unit after power on. The state shown in

Fig.5 indicates the “On” state of the unit after power on.

Fig. 4 “Off” State Fig. 5 “On” State

3.2 Mode Setting

Under the “On” state of the unit, press Mode to switch the operation modes as the following sequence:

Cooling-Dry-Fan-Heating.

Wired Controller XK19

3.3 Temperature Setting

Press ▲or ▼ to increase/decrease the preset temperature. If press either of them continuously, the

temperature will be increased or decreased by 1℃every 0.5s,as shown in Fig.6.

In the Cooling, Dry or Heating mode, the temperature setting range is 16℃～ 30℃ .

In the Fan mode, the setting temperature is xed at 26℃.

In the Auto mode, the setting temperature is unadjustable.

Fig.6

3.4 Fan Setting

Under the “On”/”Off” state of the unit, press Fan and then fan speed of the indoor unit will change

circularly as shown in Fig.7.

Fig.7

3.5 Timer Setting

Under the “On”/”Off” state of the unit, press Timer to set timer off/on.

Timer on setting: press Timer, and then LCD will display “xx.x hour”, with “hour” blinking. In this case,

press ▲or ▼ to adjust the timing value. Then press Enter/cancel to conrm the setting.

Timer off setting: press Timer, if LCD won’t display xx.x hour, and then it means the timer setting is

canceled.

Auto Low Middle High

Wired Controller XK19

Timer off setting under the “On” state of the unit is shown as Fig.8.

Fig. 8 Timer off Setting under the “On” State of the Unit

Timer range: 0.5-24hr. Every press of ▲or ▼ will make the set time increased or decreased by 0.5hr. If

either of them is pressed continuously, the set time will increase/ decrease by 0.5hr every 0.5s.

3.6 Swing Setting

Swing On: Press Function under on state of the unit to activate the swing function. In this case, will

blink. After that, press Enter/cancel to make a conrmation.

Swing Off: When the Swing function is on, press Function to enter the Swing setting interface, with

blinking. After that, press Enter/cancel to cancel this function.

Swing setting is shown as Fig.9.

Wired Controller XK19

Fig. 9 Swing Setting

Note:

① .

Sleep, Save, Turbo, Blow or Quiet setting is the same as the Swing setting.

② .

After the setting has been done, it has to press the key “Enter/cancel” to back to the setting status or

quit automatically ve seconds later.

3.7 Sleep Setting

Sleep on: Press Function under on state of the unit till the unit enters the Sleep setting interface. Then

press ▲or ▼ to switch among Sleep 1, Sleep 2 and Sleep 3. After that, press Enter/cancel to conrm the

setting.

Sleep off: When the Sleep function is activated, press Function to enter the Sleep setting interface. After

that, press Enter/cancel to can this function.

Sleep setting is shown as Fig.10.

Wired Controller XK19

Fig. 10 Sleep Setting

Sleep off is default after power failure and then power recovery, and the sleep functions is unavailable

under the fan mode.

There are three Sleep modes: Sleep 1, Sleep 2 and Sleep 3.

a. Sleep 1

In the Cooling or Dry mode, the temperature will increase by 1℃after the unit runs under Sleep 1 for 1hr

and 1℃after another 1hr.After that, the unit will run at this temperature.

In the Heating mode, the temperature will decrease by 1℃after the unit runs under Sleep 1 for 1hr and

1℃after another 1hr. After that, the unit will run at this temperature.

b. Sleep 2

In the Cooling mode, the temperature may be set between 16 ℃-23 ℃, 24 ℃- 27 ℃or 28 ℃- 29 ℃

or at 30 ℃, and their Sleep curves are shown in Fig.11 (Note: The curve is only for reference, the actual

temperature is subject to the time point.).

For example: The temperature in the Cooling mode is set at 25 ℃. Under the mode of Sleep 2, the

temperature will increase by 1℃every 1hr. After it increases by 2℃in total, it will keep at 27℃. 7 hours

later, it will decrease by1℃, i.e. 26℃.After that, the unit will keep running at 26℃.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Acondicionador de aire de Sinclair

Sinclair

Sinclair KEYON Series Manual de usuario

Sinclair

Sinclair MULTI SYSTEM SERIES Manual de usuario

Sinclair

Sinclair SDV5 Series Manual de usuario

Sinclair

Sinclair CAESAR Series Manual de usuario

Sinclair

Sinclair ASH-09AF Guía de inicio rápido

Sinclair

Sinclair Focus Plus ASH-13BIF2 Manual de usuario

Sinclair

Sinclair ASH-13AIA1 PT Manual de usuario

Sinclair

Sinclair ASH-13AIA PT Manual de usuario

Sinclair

Sinclair ASH-18AIN PT Manual de usuario

Sinclair

Sinclair ASH-18AIM2 PT Manual de usuario

Sinclair

Sinclair ASH-09AIP PT Manual de usuario

Sinclair

Sinclair SDV4 series Manual de funcionamiento

Sinclair

Sinclair AMC-15A Manual de usuario

Sinclair

Sinclair SDV5 Series Manual de usuario

Sinclair

Sinclair ASW-09BI Manual de usuario

Sinclair

Sinclair SDV5 SDV5-100EAS Manual de usuario

Sinclair

Sinclair MS-E36AI Manual de usuario

Sinclair

Sinclair MC-F09AI Manual de usuario

Sinclair

Sinclair ASDH-96AI Manual de usuario

Sinclair

Sinclair ASH-09AIM2 PT Manual de usuario

Sinclair

Sinclair MS-P12AI2 Manual de usuario

Sinclair

Sinclair ASD-42BI Manual de usuario

Sinclair

Sinclair AMC-11P Manual de usuario

Sinclair

Sinclair ASF-12A Manual de usuario

Manuales populares de Acondicionador de aire de otras marcas

Spheros

Spheros CC 355 Manual de usuario

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Manual de usuario

Panasonic

Panasonic CS-E12HKEW Manual de usuario

nedis

nedis ACMB1WT7 Manual de usuario

Samsung

Samsung AR KV Series Guía

Daikin

Daikin FCFV50A Manual de usuario

Fujitsu

Fujitsu Inverter ASBA30JFC Manual de usuario

Toshiba

Toshiba RAS-M10SMUV-E Manual de usuario

Daikin

Daikin FXLQ20MAVE Manual de usuario

Hitachi

Hitachi RAS-E24CAK Manual de usuario

CIAT

CIAT Magister 2 Series Guía

Bestron

Bestron AAC6000 Manual de usuario

Hisense

Hisense 7K Manual técnico

Frigidaire

Frigidaire FFRE0533S1E0 Manual de usuario

Samsung

Samsung AS09HM3N Manual de usuario

Frigidaire

Frigidaire CRA073PU11 Manual del propietario

Soleus Air

Soleus Air GB-PAC-08E4 Manual de usuario

McQuay

McQuay MCK020A Manual de usuario