Simplex TYCO VLC-600 Manual de usuario

Features

Model VLC-600 addressable, analog output air

aspiration smoke sensor provides:

VESDA LaserCOMPACT operation communicating

with the established TrueAlarm analog sensing process

for area coverage up to 8000 ft2

Compact 8 ⅞” (225 mm) square size

Dual stage dust filter that is used on larger systems

Obscuration measurements communicated to the fire

alarm control panel for status determination

Panel selected sensitivity from 0.016%/ft to 4.08%/ft

Local computer port access for the VESDA Vconfig

Pro software program as used on larger systems

Single LED that indicates local status information

Capability of driving a remote LED (ordered

separately)

Trouble conditions are also communicated:

Mechanical problems are received as sensor troubles

Electrical problems are received as “no answer” troubles

Additional details are indicated by the sensor LED and

by accessing sensor diagnostics

Compatible with Simplex®4100ES, 4010ES,

4100U, or legacy 4100/4120 fire alarm control

panels:

Communications via 4100ES/4010ES/4100U IDNet

or 4100ES/4100U MAPNET II addressable formats

Connection is to the same SLC (signaling line circuit)

with other devices such as addressable manual

stations, TrueAlarm area smoke sensors, addressable

control modules, etc.

Communications are as a single device and connection is

direct to the SLC without requiring a dedicated interface

4100/4120 requires revision 8.01 or higher software

Three threshold levels are programmable from the

fire alarm control panel with typical selections as:

Stage 1 – Alert at 0.016 to 0.6218% obscuration/ft

Stage 2 – Pre-Alarm at 0.03 to 0.6234% obscuration/ft

Stage 3 – Alarm at 0.05 to 4.08% obscuration/ft

NOTE: UL listed evacuation alarm sensitivity is not

to be less sensitive than 0.625%/ft

Sampling pipe network:

Uses standard Vision Systems pipe and inlet in

accordance with Vision Systems Aspire design tool

UL listed to Standard 268 (URXG)

*This product has been approved by the California State Fire Marshal (CSFM) pursuant to

Section 13144.1 of the California Health and Safety Code. See CSFM Listing

7259-1728:0109 for allowable values and/or conditions concerning material presented in

this document. This product was not approved by FM as of document revision date.

Additional listings may be applicable; contact your local Simplex product supplier for the

latest status. Listings and approvals under Simplex Time Recorder Co. are the property of

Tyco Fire Protection Products.

Typical air inlet

VLC-600 TrueAlarm

LaserCOMPACT Air

Aspiration Smoke Sensor

Fire Alarm Control Panel requires 4100ES/4010ES/4100U

IDNet or 4100ES/4100U MAPNET II communications

(4100ES shown for reference)

4100ES/4010ES/4100U IDNet

or 4100ES/4100U MAPNET II

addressable communications

TrueAlarm

Laser

COMPACT

Addressable manual stations,

TrueAlert sensors and other devices

ALARMFIRE

PULL DOWN

24 VDC power

ALARM

Clean room cable tray

Remote LED indicator

CLEAN ROOM

SMOKE DETECTOR ALARM

TrueAlarm LaserCOMPACT System Connections

Description

Air aspiration technology smoke detection operates

by actively drawing in air for sampling in a high intensity,

stable detection chamber. The Model VLC-600

TrueAlarm LaserCOMPACT smoke detector uses the

latest in VESDA sampling technology including a highly

efficient laser light source and a dual stage dust filter.

TrueAlarm analog sensing occurs when the

TrueAlarm LaserCOMPACT sensor communicates

smoke chamber information to the connected fire alarm

control panel. The panel evaluates the smoke sensor

information against three programmed thresholds and

declares an alarm or pre-alarm condition depending on

smoke chamber activity.

Status communications. In addition to smoke

chamber information, the TrueAlarm LaserCOMPACT

also advises the fire alarm control panel of local trouble

conditions. Troubles may include dirty filter, airflow

restriction or failure, etc. Specific details are stored in

memory at the sensor location.

TrueAlarm Analog Sensing

UL, ULC, CSFM Listed* VLC-600 TrueAlarm LaserCOMPACT Smoke Sensor with

4100ES/4010ES/4100U IDNet and MAPNET II Communications

S4098-0036-7 7/2013

Operation

Filtered air flow. A high efficiency aspirator

continually draws air through a simple pipe network to a

central detector. Air entering the sensor housing passes a

flow sensor before the sample is passed through a

dual-stage dust filter. The majority of air is exhausted

from the detector and where required, back vented to the

protected area. The first stage of the air filter removes

dust and dirt from the air sample before it enters the

smoke detection chamber. A second, ultra-fine filter stage

provides a clean air supply to be used inside the detection

chamber to form clean air barriers which protect the

optical surfaces from contamination.

Laser detection chamber. The detection chamber uses

a stable, highly efficient laser light source and unique

sensor configuration to achieve optimum response to a wide

range of smoke types. When smoke passes through the

detection chamber, it creates light scattering which is

detected by very sensitive sensor circuitry. The analog level

of the sensor is then communicated to the fire alarm control

panel for comparison to pre-selected alarm thresholds.

Operation (Continued)

Status logging. The sensor status history for all alarms,

service, and fault events, is monitored and logged with

time and date stamps within the electronics of the sensor,

accessible via the local computer port. General trouble

status indications are communicated to the panel as either

sensor troubles or “no answer” troubles.

Additional Information

Refer to Installation Instructions 19772 shipped with the

VLC-600 for additional information.

Model Description

VLC-600 TrueAlarm LaserCOMPACT Smoke Sensor (sampling pipe is ordered separately)

2098-9808 Remote Red LED Status Indicator on single gang stainless steel plate; mounting requires a single gang

box, 1 ½” minimum depth; connections are color coded wire leads

Sensor Voltage 18 to 30 VDC, supplied from fire alarm control panel

Sensor Current 205 mA @ 24 VDC; supervisory and alarm

Communications Compatibility 4100ES/4010ES/4100U IDNet or MAPNET II addressable

communications, automatically selected

Loading One address, one unit load per sensor

Electrical Terminations Terminal blocks for 18 to 12 AWG

Operating Conditions Sensor Ambient 14° F to 103° F (-10° C to 39° C)

Sampled Air -4° F to 140° F (-20° C to 60° C)

Sensor Humidity 10-95% RH, non-condensing

Sampling Network Maximum area of coverage = 8000 ft2, maximum pipe length in

accordance with Vision Systems computer design tool (ASPIRE) and

NFPA standards

UL Listed Velocity Range 0 to 4000 ft/min (0 to 1200 m/min)

Alarm Sensitivity Range 0.016% to 4.08%/ft obscuration, selected at the fire alarm control panel;

NOTE: UL listed evacuation alarm sensitivity is not to be less sensitive

than 0.625%/ft

Recognized Sensitivity Levels Three levels, selectable and designated as required at the fire alarm

control panel

Sensor Service Access Internal DB-9, RS-232 connection for a service computer using VESDA

Vconfig Pro software program (authorized service access only)

Enclosure Rating NEMA 1 (IP 30)

Weight 4.2 lbs (1.9 kg)

2 S4098-0036-7 7/2013

Product Selection

Specifications

Indication Meaning

OFF Power off or active sensor is waiting for panel communications

ON for approximately 3 seconds Power up self-test due to sensor being in reset cycle

ON Steady Alarm condition as commanded from panel

1 pulse approximately every 4 seconds Normal operation, pulse indicates communications with panel

3 pulses (2 Hz rate every 2 seconds) Internal fault, not communicating with panel, sensor needs internal service

diagnostics or replacement

TrueAlarm

Laser

COMPACT

8-7/8"

(225 mm)

8-7/8" (225 mm) 3-3/8" (85 mm)

LED indicator

Air exhaust location

(rear assembly can be rotated 180º to reverse intake

and exhaust locations, and knockout locations)

Air intake location

Side knockouts (2)

Top knockout location

Rear knockout

location

Mounting

bracket

3 S4098-0036-7 7/2013

Mounting Information

LED Status Indications

Tyco Fire Protection Products • Westminster, MA • 01441-0001 • USA S4098-0036-7 7/2013

www.simplexgrinnell.com

TYCO, SIMPLEX, and the product names listed in this material are marks and/or registered marks. Unauthorized use is strictly prohibited.

Otros manuales de Accesorios de Simplex

Simplex

Simplex 4098-9685 Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario