Simond store PROPANE FORGE Manual de usuario
www.simondstore.com
USER MANUAL
&
ASSEMBLY INSTRUCTIONS
FOR
PROPANE FORGE
Important Notes
Keep this Instruction Manual with you at the time of Assembly and Operation.
This will guide you the right way.
For the Adult use only.
A Product by Simond Store
Introduction to Simond Store
Description
Where to Use
Warning
Safety Instructions
Forge Body and Accessories with Identification
Part List
Unboxing
Assembly Instructions
Double Burner Oval Propane Gas Forge System
Specifications
Heat Guard Application Instruction
Operating Instruction
Burner Troubleshooting Solution
Double Burner BTU Chart & Calculation
INDEX
1
1
1
1
2
3
4
5
5
8
8
9
10
10
13
www.simondstore.com
Propane Forge is inevitable product for a Blacksmith, Hobbyist, Jeweler & Knife makers. It is ideal for heating
and bending of metals, tempering and heat treatment of small knives & agriculture use small tools.
This Propane forge is made from Steel material and its heating zone is fully insulated with Refractory Ceramic
Fiber, which can resist temperature up to 2600°F (1425°C). A rigid block of refractory fire brick placed at the
bottom of the forge to resist high velocity firing.
Introduction to Simond Store
Our Store is known for its best quality products and customer service. Customer Service has always been our
top priority. Simond Store deals in variety of products such like, various types of Propane gas Forge, Propane
gas Furnace, Jewellery Making Tools, Blacksmith & Goldsmith products, Refractory Products and many more.
We have earned customer satisfaction by providing quality product in timely manner.
www.simondstore.com Page 1 of 13
Description
Where to Use
ŸFor Outside Use Only.
(Any outside safe area of operations)
Warning
ŸImproper Installation, adjustment, alteration, service, maintenance or any mistake may result in serious
accident, damages or personal injury.
ŸRead how to Install, Assemble & operate before installing and operating.
ŸIgnorance to safety instructions may cause fire or explosion that creates many kind of risks.
Safety Instructions
ŸSafety should be always in the first priority.
ŸUse this Propane Forge after reading these entire instructions for the proper and safe
operation.
ŸAlways use this Propane Forge on a hard level non-combustible surface. This Propane Forge
is for outdoor use only. Do not use it where any kind of damage can happen. Keep fire
extinguisher nearby.
ŸThis Propane Forge is for adult use only. Keep this away from children.
ŸUse fire retardant gloves & blacksmith tong for the operation with the work-piece.
ŸWear appropriate clothes such as a leather apron. Wear goggles while watching fire of the
forge.
ŸNever leave a hot forge unattended, even if the fuel is shut off and be cautious of high
temperature of the forge parts immediately after forging session.
ŸInspect your propane cylinder (especially the valve), your regulator (especially the connector
to the cylinder and its O-ring) and your burner (especially the hose). For any signs of problems
do not install or operate.
ŸInstall the regulator by hand, without tools, until the nut (left-hand thread) is fully seated.
Immediately tighten the nut with a wrench. Do not over tighten the nut, as this will only ruin the
connectors.
ŸAlways shut down the forge by turning off the fuel at the cylinder, then backing off the regulator
knob (as a safety precaution.)
ŸOnce, Forging Session is finished, Remove the Regulator from the cylinder & take the cylinder
in outside area.
ŸAllow the forge to cool for at least half an hour before you leave the area. This is to prevent
accidental fires from going undetected.
www.simondstore.com Page 2 of 13
ŸSimond Store will not be responsible for any damage or injury caused by use
of Gas Forges.
www.simondstore.com Page 3 of 13
Forge Body
Part-A
Part-B Part-C
Part-D
Part-F
Part-H
Complementary-Maintainance Kit
Complementary-
Ceramic Fiber Blanket
Part-E
Part-G
Forge Body & Accessories with
its Identification
www.simondstore.com Page 4 of 13
Part List
Part
Description
Picture
Qty.
Forge
Part- A & B
Part-C
Part-D
Part-E
Part-F
Part-G
Part-H
Complementary
Part
Forge Body
Double Burner Set
6.5' 2 Meter Gas Hose
with Clamps
Refractory Fire Brick
Gas Pressure Regulator
with Manometer
Teflon Tape
Heatguard
Spanner
Filling Gap of Burner &
Gas Forge
1
1
1
2
1
1
1
1
1
Complementary
Part
Orifice & Maintenance
Kit for Double Burner
Shooting
1
www.simondstore.com Page 5 of 13
ŸSurface Preparation by placing Refractory Fire Brick, Castable or Concrete.
Ÿ
ŸPlace Forge over the plain surface. You may prepare it by placing refractory bricks or by using castable
cement which can withstand high temperatures.
Unboxing
ŸUnwrap all the mentioned parts as per above list.
Assembly Instructions
www.simondstore.com Page 6 of 13
ŸConnect the Pre-Assembled Burner Part A &Part B with Part C (Which is Hose). Connect one end of
hose with the Burner inlet pipe and other end with the Part E (Gas Pressure Regulator). Use clamps for
proper tightening of hose at both end.
ŸAt the top of the Part B you can see wing nut with washer which can be rotated clockwise and anti-
clockwise direction to regulate the air flow pressure while firing.
ŸConnect the above system of Part A& B at the top of the Forge with the help of the coupling and
adjustable screws. Please make sure that burner's nozzle at end do not cross over inside insulation of
forge.
ŸPlace Part D (Bricks) at the bottom of the Forge and over the ceramic fibre lining.
www.simondstore.com Page 7 of 13
ŸConnect Gas regulator with the propane Cylinder. Don't forget that pressure regulator has left thread. Check
that there is no loose fitting of parts which may lead to gas leakage.
ŸLight up the forge by using lighter at the opening of the burner inside the forge body.
ŸNow Forge is ready for the firing.
Why this gap filling is necessary?
ŸTo Prevent the heat loss.
ŸHeat Loss damage this area of
furnace.
Pre-Rigidized
Ceramic Fiber
Insulation.
www.simondstore.com Page 8 of 13
Double Burner Oval Propane Gas Forge
System
Specifications
Forge Type : Double Burner Oval Forge (MS)
Shape : Oval
Burner : Double Burner
Inside Floor : 1” Thick Refractory Fire Brick – 2 Nos.
Forge Body Construction : 16 Gauge (1.5mm) MS
Forge Internal Dimensions : 3.2” (H) x 6.7” (W) x 18.8” (L)
Operating Temperature : 2500°F (1370°C)
Inside Insulation Material : 1” Thick Refractory Ceramic Fiber, 2600°F,10 Pcf
Burner Nozzle Material : SS-304
Rigidizer : It is pre-rigidize
Otros manuales para PROPANE FORGE
1
Tabla de contenidos
