Silver Ticket SIE-169106 Manual de usuario
Instruction Manual for Motorized, Recessed In-Ceiling Screens
Thank you for choosing Silver Ticket Products. Please follow the instructions in this manual and
keep it for future reference.
Instruction Manual for Motorized, Recessed In-Ceiling Screens
Product Overview
Parts Included
1
Instruction Manual for Motorized, Recessed In-Ceiling Screens
Preparation
Take out all the parts from the packaging and verify that all the parts have been included, then
follow the steps below to install the screen.
Note 1.1: When installing the projection screen it is important to choose the correct fasteners
for the ceiling type. Choosing the wrong fasteners can lead to severe injuries or screen damage.
1. Choose a proper location on the ceiling to install the projection screen. Be sure that no
load-bearing supports will be cut or compromised during the installation.
2. Measure the total length of the case w/ flanges attached (A) as shown (Fig. 1
). Subtract
20mm (0.75”) from that value (A) to get the hole cut-out length. The cut-out width is
140mm (5.5”).
3. After determining the location of the screen and the cut-out dimensions (Fig. 2
), proceed to
cut the hole in the ceiling. This step cannot be undone, so be sure the measurements are
correct before making any cuts.
2
Instruction Manual for Motorized, Recessed In-Ceiling Screens
4. The distance between the center of each bracket is A (the measurement from Fig. 1 above
)
minus 116mm (4.5”). The mounting holes for each bracket are 48mm (1.875”) apart. Mark
the location of each mounting hole for both brackets (Fig. 3
).
3
Instruction Manual for Motorized, Recessed In-Ceiling Screens
Installation Instructions
1. Slide four M5 screws (two along each track) onto the screen case (Fig. 1
). Place the first
screen bracket on the screen case aligned with the four screws (Fig. 2
). Slide the bracket so
that there is no gap between the bracket and the end of the screen case. Secure the bracket
with a nut on each screw (Fig. 3
). Repeat this step for the second bracket on the other end.
2. Slide the threaded installation rods through the holes in the each ceiling-mount bracket and
secure each rod on both sides with nuts until the ceiling-mount brackets are secure (Fig. 4
).
Install the ceiling brackets (Fig. 5
) at the previously marked locations (see Preparation
Instructions
).
3. Be sure that the screen case is facing the correct direction. The screen controls should be
on the left side of the case when looking at the viewing side of the screen. Lift the screen
up so that the threaded hanging rods slide into the holes in the case mounting brackets
(Fig. 6
). Secure the screen in place with nuts threaded onto the hanging rods (Fig. 6,7
).
4
Instruction Manual for Motorized, Recessed In-Ceiling Screens
Note 3.1: At this step you may want to attach external wiring, power, etc. to test the screen’s
operation before fully installing it into the ceiling.
4. To secure the screen into its final location, tighten the nuts below each case mounting
bracket (Fig. 8
) until the screen trim is flush with the ceiling (Fig. 9
).
5
Instruction Manual for Motorized, Recessed In-Ceiling Screens
5. Install the screen trim flanges. Each trim flange snaps into small groves near the bottom of
the left and right sides of the screen case. The screen should now be fully installed and the
cut-out hole should not be visible since it is covered by the trim flanges.
Note 5.1: For adjusting the automatic stop limits of your screen please see Appendix A:
Adjusting the Screen Limits in this guide for steps to set the stop locations for both upper and
lower screen retraction and extension.
6
Instruction Manual for Motorized, Recessed In-Ceiling Screens
Controlling the Screen
There are many different options included to control the projection screen. Only connect the
screen to the options that will be used.
Note 1.1: When the screen is set to manual control, only manual control of the screen will work.
For any other type of control set the screen to remote control.
1. Manual Control. The push-button located on the left end of the screen face near where the
projection screen extends. Pushing the button will cause the motor to switch between
three modes: extend, stop, and retract. The state change pattern can be seen in the
diagram below:
7
Instruction Manual for Motorized, Recessed In-Ceiling Screens
2. Trigger Connection. The trigger jack recognizes outputs of DC 5V-12V. When power is
sensed the screen will automatically lower. When power is off the screen will rise back into
the case.
3. IR Remote. The remote control will work up to 25’ from the IR eye and an angle of up to 30°.
The remote will not work if the signal or receiver is covered. Keep the remote away from
high temperatures and humidity. Change the battery when the signal is low; be sure to use
the same type of battery as the original.
8
Instruction Manual for Motorized, Recessed In-Ceiling Screens
4. RS-232. Home automation systems that are compatible with RS-232 communication can
remotely operate the screen via the RJ-45 connector on the left-side control panel.
9
Tabla de contenidos
