Silicon Image SteelVine SiI 4726 Manual de usuario
Package Contents
•Unpacking Instructions
•SiI 4726 Storage Appliance
•Two-meter length external SATA cable
•AC power cord
•CD-ROM containing:
•SiI 4726 Manager Software
•Quick Installation Guides
•User's Guides
If ANY of the contents are missing or appear damaged, please contact
your dealer/distributor immediately.
Product Registration
Thank you for purchasing SteelVine products. Please register this
product at www.steelvine.com/product_registration. Registering the
product ensures the validity and terms of the warranty.
For environmental and regulatory information, please go to:
http://www.siliconimage.com/products/product.aspx?id=47
Copyright © 2005, Silicon Image, Inc. All rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, or translated into any language or computer format, in
any form or by any means without prior written permission of:
Silicon Image, Inc.
1060 East Arques Ave.
Sunnyvale CA 94085
Silicon Image and the Silicon Image logo are the trademarks or registered trademarks of
Silicon Image, Inc. ("Silicon Image") in the United States and other countries. The
information contained in this document is provided by Silicon Image merely as a courtesy
and is, to the knowledge of Silicon Image, accurate. However, Silicon Image is under no
obligation to update and/or keep current the information contained in the document. Silicon
Image disclaims any and all liability resulting from the use of the information contained in
this document and any reliance on such information shall be at the sole risk of the relying
party. Silicon Image expressly reserves the right to change the information contained
herein without notice."
Document Number: DOC-004726-203
Revision: 1.3
Quick Installation Guide
(Windows)
SiI 4726
Storage Appliance
SiI 4726 Installation
Introduction
The SiI 4726 Storage Appliance is a five-drive array that connects to the
external SATA connector on your host computer.
Prerequisites
Hardware •Intel PIII 500MHz equivalent or faster
•CD-ROM drive
•64 MB of RAM minimum
•250 MB of free hard disk space
•Super VGA (800 x 600) or higher resolution with 256 colors
•Mouse or compatible pointing device
•External SATA cable connection between the SiI 4726
Storage Appliance and host computer
•SteelVine Host Bus Adapter card, part number
SV-HBA3124, or another SATA host controller with Port
Multiplier (PM) support
Software •Microsoft Windows 2000, Windows XP, or Windows Server
2003 with the latest service pack installed
•SV-HBA3124 CD
•SiI 4726 CD
Procedure
1. Turn off your host computer.
2. Connect one end of the external SATA cable to the external SATA
connector on your host computer. If needed, install the SV-HBA3124
card and driver (see the SV-HBA3124 Quick Installation Guide).
3. Connect the other end to the SiI 4726 Storage Appliance.
4. If hard disk drives are not installed in the appliance, insert the drives
most of the way into each bay; flip out the drive carrier lever, gently
insert the drive carrier until the drive is almost fully inserted then
push the lever shut to seat the drive securely.
5. Attach one end of the AC cable to the SiI 4726 Storage Appliance
and the other end to the proper AC receptacle.
6. Turn on the SiI 4726 Storage Appliance.
7. Turn on the host computer.
8. Right-click My Computer on your desktop and select Manage from
the pop-up menu.
9. Select Disk Management under Storage to view the disk drives.
10. If an Initialize and Convert Disk Wizard appears, click Cancel.
11. Verify an unpartitioned SiI 4726 disk is visible. Another unallocated
disk, with no capacity, represents the SiI 4726 processor. Do not
initialize or partition this SiI 4726 processor disk.
12. If you plan to use the currently defined configuration mode, format
the un-partitioned disk so it is recognized as a volume. Otherwise,
follow these steps to install the SiI 4726 Manager software:
•Insert the SiI 4726 installation CD in the CD-ROM drive.
•Open the installation CD and select the Windows folder.
•Double-click the setup.exe file.
•Run through the standard install process (read and accept
license agreement, default file location, etc.).
•Select Start > All Programs > SiI4726 > SiI4726Manager to
start the SiI 4726 Manager.
•Follow the instructions in the SiI 4726 Manager User's Guide to
create logical volumes, select storage policies for the volumes,
and partition the disks in the Windows Disk Management utility.
13. For a quick install, Double-click the SilentInstall.bat file. This will
automatically install the SteelVine Manager in the default locations.
Otros manuales de Almacenamiento de Silicon Image
Manuales populares de Almacenamiento de otras marcas
Spectra Logic
Spectra Logic T-Series Spectra T50e Manual de usuario
Panasonic
Panasonic LKM-F931-1 Manual de usuario
Tabernus
Tabernus Enterprise Erase E2400 Manual de usuario
Rocstor
Rocstor COMMANDER 3F series Manual de usuario
HP
HP P9000 Manual de usuario
Western Digital
Western Digital Ultrastar Data60 Manual de usuario