SilentWind Hybrid 600 Instrucciones de funcionamiento

Troubleshooting

Low power problem

V28_03_2019

Troubleshooting_Low_Power_v28_03_2019

Download section at: https://www.silentwindgenerator.com/en/download/


Troubleshooting_Low_Power_v28_03_2019 
Download section at: https://www.silentwindgenerator.com/en/download/ 
 
Index 
 
Tables .........................................................................................................................................................4 
1 Device settings on Hybrid 600............................................................................................................4 
2 Device settings on Hybrid 1000..........................................................................................................4 
3 Device settings Hybrid Boost PWM version.......................................................................................4 
4 Device settings Hybrid Boost MPPT version.......................................................................................5 
5 Resistance winding values..................................................................................................................5 
How to measure the resistance on the AC cables ....................................................................................6 
Recommended check sequence................................................................................................................6 
1 Near the controller.............................................................................................................................6 
2 At the wind generator AC wires .........................................................................................................7 
3 At the wind generator windings.........................................................................................................7 
How to remove the wind generator windings..........................................................................................9 
How to clean the Slip Ring.......................................................................................................................11 
Silentwind help request contact .............................................................................................................15 
 
 
 
 
 

Troubleshooting_Low_Power_v28_03_2019

Download section at: https://www.silentwindgenerator.com/en/download/

1. Tables

1.1 Device settings on Hybrid 600

Values

12V

24V

Charge off

14,4V

28,8V

Breake on

27 - 29A

15A

Break time

50 s

1.2 Device settings on Hybrid 1000

Values

12V

24V

Charge off

14,4V

28,8V

Brake on

27A - 29A

15A

1.3 Device settings Hybrid Boost PWM version

Values

12V

24V

48V

Absorption

13,4V

27,8V

56,6V

Overvoltage

16V

32V

64V

Low Wind Boost

10V

Storm Brake

32A

16A

Under Voltage Switch off

10,8V

21,6V

43,2V

Under Voltage Recovery On

12V

24V

48V

Solar Switch off

1,5V

Solar Switch on

Troubleshooting_Low_Power_v28_03_2019

Download section at: https://www.silentwindgenerator.com/en/download/

1.4 Device settings Hybrid Boost MPPT version

1.5 Resistance winding values

Values

Version

12V

24V

48V

Hybrid 1000

0,5 Ω

1,7 Ω

5,5 Ω

Hybrid Boost PWM

0,2 Ω

0,5 Ω

1,2 Ω

Hybrid Boost MPPT

0,3 Ω

0,5 Ω

1,2 Ω

IMPORTANT NOTE!

It’s very important for you to choose the proper

multimeter since wrong measurements will lead to

wrong interpretations.

On the left side, the multimeter range is 1 Ωand

it’s not able to read the resistance correctly.

On the right side the range it’s 0.001Ω and the

measure is done correctly.

Values

12V

24V

48V

End of charge voltage

14,4V

28,8V

57,6V

Overvoltage

16V

32V

64V

Low Wind Boost

10V

Storm Brake

32A

16A

Under Voltage Switch off

10,8V

21,6V

43,2V

Under Voltage Recovery On

12V

24V

48V

Solar Switch off

1,5V

Solar Switch on

Troubleshooting_Low_Power_v28_03_2019

Download section at: https://www.silentwindgenerator.com/en/download/

How to measure the resistance on the AC cables

2. Recommended check sequence

-After this point, we will assume that your controller settings are correct. Please check your device

setting values on chapter 1.

2.1 Near the controller

We start to measure the entire system near the controller:

-The values are described at 1.5 table.

-Stop the wind generator as described at the warning sign at 0.

-Remove the AC cables from the controller to perform the measurements.

-If the measurements are out-of-range, go to next step.

-If the measurement values are correct, you might have a damaged controller. Please contact

Silentwind.

AC Cables

1 2 3

-Set your Multimeter to Ohmimeter to the lowest scale.

-Measure all three possible combinations:

oFrom 1 to 2

oFrom 1 to 3

oFrom 2 to 3

- Before doing these measurements, you must stop the wind generator.

It’s recommended that you tie the blades to avoid them to rotate.

- A minimum knowledge how to set the Multimeter is needed.

Wind AC Input

Measure here

Troubleshooting_Low_Power_v28_03_2019

Download section at: https://www.silentwindgenerator.com/en/download/

2.2 At the wind generator AC wires

Measure here

Measure directly in the Silentwind wind generator wires.

-The values are described at 1.5 table.

-If the measurements are in range, it means that the extension cables are faulty and should be

repaired/replaced.

-If the measurements are out-of-range, proceed to the next step.

2.3 At the wind generator windings

Measure here.

3.3.1. To be able to measure on the windings, you should

remove the nose cone and the Hub + Blades by removing the

M16 Nut (please read the assembly instructions on the user

manual).

Troubleshooting_Low_Power_v28_03_2019

Download section at: https://www.silentwindgenerator.com/en/download/

3.3.2. Unscrew the 3 screws on the front plate (please be careful not to

damage the front face paint). The front face should go out easily.

3.3.3. Unscrew the wires that are connected to the PCB and perform the measurements (you don’t need to

completely remove the windings).

-If the readings on the windings are wrong, they are damaged and must be replaced. To remove the

windings, please follow How to remove the wind generator windings chapter.

-If the readings are in range, you should clean the Slip Ring. Please read the How to clean the Slip

Ring chapter.

To assemble the device, follow the instructions backwards.

Do not forget to insert the O ring correctly!

Measure here.

Troubleshooting_Low_Power_v28_03_2019

Download section at: https://www.silentwindgenerator.com/en/download/

3. How to remove the wind generator windings

Remove the 3 front face screws.

Be careful not to chip the front face paint.

The front face can be easily removed.

Unscrew the three marked screws and the font face set can be removed from the body.

Troubleshooting_Low_Power_v28_03_2019

Download section at: https://www.silentwindgenerator.com/en/download/

Removing the rotor, it’s not difficult but it can be a bit tricky. Please be careful not to harm yourself neither

the equipment.

To remove the rotor, you can press the axis against a table to go half way then pull it out completely.

The windings are usually sold with the front face but if you pretend to completely remove the stator, you

must use a rubber hammer and hit the front face to be able to release it.

As small press is used to assemble the front face and the stator, so we do not recommend the end-user to

do this job since it’s time consuming and there’s a high risk of something goes wrong.

Please notice that industrial magnets are not toys! You can get seriously injured.

Front face set exploded view.

To assemble the device, follow the instructions backwards.

Do not forget to insert the O ring correctly!

Be careful not to chip the paint .

Use the correct tools.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de turbina eólica de otras marcas

Orchard-Rite

Orchard-Rite 1300 Series Manual de usuario

FlexPro

FlexPro EOL Series Manual de usuario

BWC

BWC EXCEL 1 Manual de usuario

Automaxx

Automaxx 600 Watts Wind Turbine Manual de usuario

Enair

Enair E200 Manual de usuario

Nemo

Nemo FSH400 Manual de usuario

Spreco

Spreco Silentwind Manual técnico

ABB

ABB A100-L Series Manual de usuario

Primus Wind Power

Primus Wind Power Air 40 Manual de usuario

Tesup

Tesup i-1500 Manual de usuario

Valen

Valen Hyland 920 Manual de usuario

Automaxx

Automaxx 400 Watt Turbine Manual de usuario

my!WIND

my!WIND 10 kW wind turbine Manual de usuario

Spreco

Spreco SHARKY Manual

Futurenergy

Futurenergy AirForce1 Guía de instalación

Nemo

Nemo Shootpower NEMO500 Manual de usuario

EST

EST 2KW WIND TURBINE Manual de usuario

AWS

AWS AWS2000 Manual de usuario