SILENCE SCUTUM S02 Manual de usuario
1
USER MANUAL
SCUTUM S02
2
GENERAL CONTENTS
1.- General characteristics of the vehicle
2.- Technical specifications of the battery and charger
3.- Maintenance program
4.- Warranty of the Vehicle and the battery
3
GENERAL CHARACTERISTICS OF THE VEHICLE
0. GENERAL SPECIFICATIONS
1. VEHICLE IDENTIFICATION
1.1 VIN - FRAME MARKING
1.2 INFORMATIVE LABEL - PRODUCTION PLATE
1.3 MAXIMUM PERMITTED LOAD
2. GENERAL COMPONENTS
2.1 MAINSTAND AND SIDESTAND
2.2 MIRRORS
2.3 FUSE BOX
2.4 REAR WHEEL (MOTOR)
2.5 LIGHTS
2.6 UNDER SEAT STORAGE COMPARTMENT
2.7 TAIL BOX
3. CONTROLS
3.1 LEFT SWITCH CONTROLS
3.2 COMBINED BRAKE AND REGENERATIVE BRAKE
3.3 RIGHT SWITCH CONTROLS
3.4 IGNITION SWITCH
3.5 KEY GUARD
4. INSTRUMENT PANEL
4.1 SPEEDOMETER
4.2 PANEL
5. DISPLAY
5.1 MAPING OF THE ELECTRIC MOTOR
5.2 SERVICE
5.3 READY AND BATTERY, MOTOR AND CONTROLLER TEMPERATURES
5.4 VEHICLE CHARGE INDICATOR
5.5 SPEEDOMETER ERRORS
4
GENERAL SPECIFICATIONS
Motor
Type
Specifications
Motor (maximum torque / maximum power)
Type
Maximum speed
Position
161.4 Nm / 4 KW
BRUSHLESS HUB MOTOR 13”
80 Km/h
On wheel
Regenerative brake
Motor brake
Reverse speed
0 Emissions
LED lighting
Battery specifications
2 kWh (Pack 1)
4 kWh (Pack 2)
6 kWh (Pack 3)
Capacity
Cell chemistry
Weight
Battery nominal voltage
2200 kWh 44 Ah
Lithium-ion cells
19.5 Kg
48 V
4200 kWh 82.5 Ah
Lithium-ion cells
30.2 Kg
48 V
5500 kWh 107.3 Ah
Lithium-ion cells
35.8 Kg
48 V
Charger Type
Standard charging time
On-board 600 W
3 hours 100%
On-board 600 W
6 hours 100%
On-board 600 W
8 hours 100%
Riding modes & maximums
2 kWh (Pack 1)
4 kWh (Pack 2)
6 kWh (Pack 3)
Maximum speed
Maximum range
E 25 km/h
E 65 km
C 40 km/h
C 45 km
S 45 km/h
E 40 km
E 45 km/h
E 120 km
C 60 km/h
C 90 km
S 75 km/h
E 80 km
E 45 km/h
E 180 km
C 60 km/h
C 130 km
S 75 km/h
E 110 km
5
Frame
Specifications
Material
Wheel base
Height from ground
Seat height
Weight without battery
Maximum carrying capacity
Steel
1910x710x1260 mm
1482 mm
137 mm
85 Kg
175 Kg
General specifications
Specifications
Wheels
Tyres
Front tyre pressure
Rear tyre pressure
Brakes
Front / rear suspension
Suspension
13”X3.5
130/60-13
1.8 bar
2.5 bar
220 mm disc
Hydraulic with 232 oil
Front telescopic fork
Accessories (optional)
Tail boxes
Document holder on leg guard
Windshield
Smartphone support and charger
Factory remote connection
Electronic data registers
Safety
Protection against short circuits.
Protection against voltage dips and surges.
Protection for low and high voltage.
Protection against high temperatures of the engine, battery and controller.
6
1. VEHICLE IDENTIFICATION
1.1 VIN - FRAME MARKING
The VIN is an alphanumeric 17-digit code which is used to identify your scooter. The VIN standard is established by the ISO
laws. The VIN is required when ordering spare parts.
The VIN is stamped on the steering pipe, below the plastic cover. It is engraved directly on the frame.
To access the VIN, remove the plastic cover by applying pressure to the upper part of the cover.
7
1.2 INFORMATIVE LABEL - PRODUCTION PLATE
This scooter has a label which displays the frame number, the maximum permitted noise level and the rpm.
The label is at the rear of the scooter, towards the right side, very close to the wheel.
1.3 MAXIMUM PERMITTED LOAD
The maximum weight of this scooter is 315 kg, including the rider and the maximum carrying capacity. This weight limit
is shown in all the specifications tables.
8
Maximum Total Weight 315 kg.
Maximum Total Load 170 kg.
Maximum Load in Central Zone Not Specified
Maximum Capacity in Under Seat Storage Compartment 3.7 Litres
Maximum Capacity in Tail Box 75 kg.
Center of the
scooter
Underseat luggage
compartment
Space for a
rear box
9
2 GENERAL COMPONENTS
The general components of this scooter are:
Front fender
Speedometer
Rear
Mirrors
Seat
Front wheel
Battery
Sidestand
Mainstand
Rear wheel
(Motor)
Break light,
Blinkers
10
2.1 MAIN STAND AND SIDE STAND
SIDE STAND
The side stand is on the left side of the scooter.
To use the side stand, push the bar downwards with your
foot from the side support.
The side stand is used when the ground is too uneven, or
sloped to use the main stand.
MAIN STAND
The main stand is underneath the scooter centre line.
This stand is used to keep the scooter in a vertical position.
To lower the stand, push the arm down with one foot while
slowly pushing the scooter forwards and upwards.
The main stand is used when the ground is even and flat
and when the scooter is going to be parked for a long
period of time.
Both stands are reinforced at the fastening point in order to
withstand intensive pressure throughout use.
Tabla de contenidos
Otros manuales de Scooter de SILENCE
