SIIG CE-DV0031-S1 Manual de usuario
3-Port DVI Splitter
CE-DV0031-S1
Quick Installation Guide
2
Safety and Notice
The 3-Port DVI Splitter has been tested for conformance to safety regulations and
requirements, and has been certified for international use. However, like all electronic
equipments, the 3-Port DVI Splitter should be used with care. Please read and follow the
safety instructions to protect yourself from possible injury and to minimize the risk of
damage to the unit.
Follow all instructions and warnings marked on this unit
Do not attempt to service this unit yourself, except where explained in this manual
Provide proper ventilation and air circulation and do not use near water
Keep objects that might damage the device and assure that the placement of this unit
is on a stable surface
Use only the power adapter and power cords and connection cables designed for this
unit
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to
the device before cleaning
3
Features
Package Contents
The 3-Port DVI Splitter receives and reconstructs (equalizing & re-clocking) a DVI
signal and distributes it to three identical outputs. It can be cascaded with one
another in order to obtain more DVI outputs (up to 6 tiers). It will also process (read
& store) the EDID information sent over the Data Display Channel (DDC).
Connects a DVI video source to 3 DVI compatible displays (comes with a DVI
Y-cable)
Perfectly as a repeater by regenerating the DVI signal
Stackable, 8 devices stacked can support up to 17 outputs
Reads and remembers the EDID of displays
Can be modified EQ with two modes
Extends greater than 45 ft of input/output DVI cable
Introduction
3-Port DVI splitter
DVI Y-cable
5V DC power adapter
Quick Installation Guide
4
Technical Specifications
Input connector: 1 x DVI-I
Output connector: 2 x DVI-I
Maximum Resolution: 1600 x 1200
LEDs:1 x Green (ID), 1 x Red (Power)
DIP switch: 2
Power Supply: 5V DC
Dimensions: 12mm (L) x 88mm (W) x 25mm (H)
Weight: 300g
5
Front View
Rear Panel
Panel Descriptions
3. 5V DC
4. Connect a device equipped with DVI output (such as a PC) to 3-Port DVI
Splitter here.
5. Rotary switch- Assign an ID (0-7) for the device while cascading. Fo
r
example, you can set rotary switch at 1 for the first 3-Port DVI Splitter and 2
for the second 3-Port DVI Splitter. Please ignore the rotary switch when
only a single 3-Port DVI Splitter exists.
6. Green LED- lights when the 3-Port DVI Splitter is selected.
7. Red LED- lights when power on.
8. Infrared Receiver (optional)
1. Connect a DVI display here.
2. Connect a DVI display or two displays by a DVI Y-cable.
*While cascading, use the short line of the DVI Y-cable to connect to the next splitter input an
d
the long line to connect to a display.
6
Button View
Mode
On Open EQ. Less noise but more power consumption.
1 Off Close EQ.
On Writing default EDID.
*Set the DIPswitch at on and plug in power cord. The green LED will light after the writing process
is completed.
2
Off Record EDID of the connected display via DVI-OUT1
*Plug in DVI cable first from the display and then plug in power cord. The recording process willbe
initiated and the green LED lights. The green LED will turn of after the reading process is
completed.
Warning!! Don’t plug in DVI source while the 3-Port DVI Splitter is writing
default EDID or recording EDID from displays. This will cause damage to
the EDID in the flesh memory.
If you cannot boot your computer from the connected 3-Port DVI Splitter
due to the damaged EDID in the 3-Port DVI Splitter, please proceed the
“Writing default EDID” and then “Recording EDID of the connected
display”. This will enforce the 3-Port DVI Splitter to write the EDID from
display.
7
We suggest you connect the monitor with the lowest resolution to the DVI-OUT 1.
(E.g. Suppose monitor A might support a maximum resolution of 1920 x 1200,
monitor B supports a maximum resolution of 1280 x 1024 and monitor C supports a
maximum resolution of 1024 x 768, please connect monitor C to DVI-OUT 1).
Unless you would like to use the default universal EDID, please set DIP switch 2 at off
position, which allows the 3-Port DVI Splitter to read the first connected monitor’s
EDID.
1. Single Device
2. Mutiple devices- cascading
Hardware Installation
1. Connect a monitor, a projector or other displays with DVI input by a
male-to-male DVI cable to the first 3-Port DVI Splitter DVI-OUT 1.
2. Plug DVI Y-cable into 3-Port DVI Splitter DVI-OUT 2 and then plug in powe
r
adapter.
3. Connect the second display to the DVI female connectors of the long line of the
Y-cable and plug in the short line of the Y-cable to the DVI-IN of the second
3-Port DVI Splitter.
4. Connect the third display to the DVI-OUT 1 of the second 3-Port DVI Splitter.
5. Follow from step 2 to step 4 for cascading the remaining devices.
6. Connect a PC or other devices with DVI outputs to the first 3-Port DVI Splitte
r
DVI-IN.
1. Connect a monitor, a projector or other displays with DVI inputs by a
male-to-male DVI cable to 3-Port DVI Splitter DVI-OUT 1.
2. Plug DVI Y-cable into 3-Port DVI Splitter DVI-OUT 2
3. Connect the second and third displays to the DVI female connectors of the
Y-cable.
4. Plug power adapter cable into 5V DC jack.
5. Connect a PC or other devices with DVI out
p
uts to DVI S
p
litter DVI-IN.
8
Monitor 1
Monitor 2
Monitor 4
Monitor 6
DVI
PC
1st DVI Splitter
2nd DVI Splitter
3rd DVI Splitter
4th DVI Splitter
Monitor 3
Monitor 5
Y-cable
9
Blank Page
10
Blank Page
Otros manuales para CE-DV0031-S1
1
Tabla de contenidos
Otros manuales de Convertidor de medios de SIIG
SIIG
SIIG AV-GM08K3-S1K Manual de usuario
SIIG
SIIG AV-GM08K3-S1S Manual de usuario
SIIG
SIIG AV-GM08R3-S1 Manual de usuario
SIIG
SIIG DP USB 3.0 4-Port PCIe i/e VL Manual de usuario
SIIG
SIIG CV-009S Manual de usuario
SIIG
SIIG JU-HS2012-S4 Manual de usuario
SIIG
SIIG AV-GM01Q3-S1A Manual de usuario
SIIG
SIIG AV-GM0903-S1 Manual de usuario
SIIG
SIIG AV-GM0513-S1 Manual de usuario
SIIG
SIIG CE-H22W11-S1 Hoja de información del producto
SIIG
SIIG AV-GM0A43-S1 Manual de usuario
SIIG
SIIG CE-H26E11-S1 Manual de usuario
SIIG
SIIG FE-CXST11 Manual de usuario
SIIG
SIIG AV-GM06R3-S1 Manual de usuario
SIIG
SIIG CE-HM0031 Manual de usuario
SIIG
SIIG ID-SC0011-S1 Manual de usuario
SIIG
SIIG AV-GM01Q3-S1DS Manual de usuario
SIIG
SIIG RS-232 to Multi-Mode Fiber Optic Manual de usuario
SIIG
SIIG CyberX ID-SC0H11-S1 Manual de usuario
SIIG
SIIG ID-SB0011-S1 Manual de usuario
