SignaMax 065-1096 Manual de usuario

10/100/1000BaseT/TX to 1000BaseSX/LX

User’s Manual

Issue date: April 2008

065-1096 10/100/1000BaseT/TX TO1000BaseSX/LX GIGABIT SFP MEDIA CONVERTER

or transmitted in any form or by any means, whether electronic, mechanical, photo copying,

recording or otherwise, without the prior written permission of the publisher.

FCC WARNING

This equipment has been tested and found to comply with the limits for a class A device,

pursuant to part 15 of FCC rules. These limits are designed to provide reasonable protection

against harmful interference in a commercial installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communication. Operation of this

equipment in a residential area is likely to cause harmful interference, in which case, the user

will be required to correct the interference at the user’s own expense.

This is a Class A product. In a domestic environment, this product may cause radio interference

in which case the user may be required to take adequate measures.

Take special care to read and understand all the content in the warning boxes:

Warning

065-1096 10/100/1000BaseT/TX TO 1000BaseSX/LX GIGABIT SFP MEDIA CONVERTER

TABLE OF CONTENTS

1ABOUT THIS GUIDE................................................................................1

1.1 Welcome.................................................................................................1

1.2 Purpose..................................................................................................1

1.3 Terms/Usage..........................................................................................1

1.4 Features .................................................................................................1

1.5 Specifications .........................................................................................2

1.6 Package Contents..................................................................................2

2HARDWARE DESCRIPTION...................................................................3

2.1 Product Overview...................................................................................3

2.2 Product Illustrations................................................................................4

2.3 DIP Switches..........................................................................................4

3LED INDICATORS ...................................................................................5

4INSTALLATION........................................................................................6

4.1 Location..................................................................................................6

4.2 10/100/1000BaseT/TX Port (RJ-45)........................................................6

4.3 Gigabit SFP Slot.....................................................................................6

4.4 Link Fault Signaling ................................................................................7

4.5 Desktop Installation................................................................................7

4.6 Powering On the Unit .............................................................................7

5APPENDIX: APPLICATION DIAGRAMS..................................................8

5.1 Application Diagram I .............................................................................8

5.2 Application Diagram II ............................................................................8

065-1096 10/100/1000BaseT/TX TO 1000BaseSX/LX GIGABIT SFP MEDIA CONVERTER

1 About This Guide

1.1 Welcome

Thank you for choosing the Signamax 10/100/1000BaseT/TX to 1000BaseSX/LX SFP

Media Converter. This device integrates Gigabit Ethernet triple-speed copper segments and

Gigabit fiber segments in a highly flexible package.

1.2 Purpose

This guide discusses how to install and configure your 10/100/1000BaseT/TX to

1000BaseSX/LX SFP Media Converter.

1.3 Terms/Usage

In this guide, the term “Converter” (first letter upper case) refers to your

10/100/1000BaseT/TX to 1000BaseSX/LX SFP Media Converter, and “converter” (first

letter lower case) refers to other converters.

1.4 Features

Standards:

•IEEE 10/100BaseT/TX

•IEEE 802.3ab 1000BaseT

•IEEE 802.3z 1000BaseSX/LX

Interface:

•One 10/100/1000 Mbps Ethernet port

•Auto MDI/MDI-X support on RJ-45 port

•One SFP slot for a Gigabit Ethernet fiber optic link

•Extends distances up to 550m (1,804.46 ft) for multimode 850 nm fiber modules,

110 km (317,625 ft) for singlemode fiber modules(dependent on SFP module chosen)

Management:

•Alarm LED illuminates to indicate link failure

•Status LEDs for easy monitoring of device’s status

Mechanical & Environmental:

•External power supply

•FCC Class A & CE approved

065-1096 10/100/1000BaseT/TX TO 1000BaseSX/LX GIGABIT SFP MEDIA CONVERTER

1.5 Specifications

Standards: IEEE 802.3 (10BaseT Ethernet); IEEE 802.3u (100BaseTX/ Fast

Ethernet); IEEE 802.3ab (1000BaseT); IEEE 802.3z 1000BaseSX/LX

Connectors: 1x RJ-45

1x Fiber SFP

Max.

Distance: UTP: 100m (Cat 5/5e/6)

Fiber Optic: SFP; up to 550m (MM, 850 nm), 110 km (SM)

Cable: Multimode fiber optic: 50/125 or 62.5/125um

Singlemode fiber optic: 9/125um

Copper: Cat 5/5E/6

Data Rates: Fiber: 1000 Mbps

Copper: 10/100/1000 Mbps

Unit LED:

PWR:

ALM:

LNK/ACT:

(Fiber Link)

Illuminated for normal operation

Illuminated when failure occurs on fiber or copper link

Illuminated when receiving link pulses from compliant

devices

Flashing when data packets being transmitted or

received via fiber port

DIP Switches: DIP 1 – LFS: Enable/disable Link Fault Signaling (LFS)

Power: 12V DC @ 0.5A, external power supply adapter

Frequency: 50Hz to 60Hz

Environment: Temperature:

Relative Humidity:

Storage:

Relative Humidity:

Operating: 0°C to 50°C

10% to 90%, non-condensing

-20°C to 70°C

5% to 90%, non-condensing

Emissions: FCC Part 15 of Class A & CE approved

Dimensions: 110 x 74 x 23.4mm (L x W x H)

1.6 Package Contents

The package should include the following:

•One Converter unit

•One power adapter (please check connector type and input power specification)

•Four self-adhesive pads

•User’s Manual

065-1096 10/100/1000BaseT/TX TO 1000BaseSX/LX GIGABIT SFP MEDIA CONVERTER

2 Hardware Description

2.1 Product Overview

The 10/100/1000BaseT/TX to 1000BaseSX/LX SFP Media Converter is primarily

designed for larger workgroups, which demand higher speed and broader bandwidth

and requires migration and expansion from copper-based Gigabit triple speed to Fiber-

based Gigabit networks.

It features an automatic MDI/MDI-X on the RJ-45 port that allows for direct connection

to a workstation, switch or hub. Now, the network manager does not need to worry

about the cable configuration (crossover or straight through) when establishing

connection between RJ-45 ports.

It features both an RJ-45 jack and an SFP slot which allows it to easily integrate a

1000BaseT network with a 1000BaseSX/LX fiber network.

If the LFS DIP switch is set to ON, the Link Fault Signaling function is enabled. If the

copper link is down, the fiber port will be disabled by the Converter. If the fiber port

loses signal, the copper port will be disabled by the Converter. These two types of

disabling actions will enable the spanning tree protocols of the neighboring switch to go

into effect.

The Media converter is specifically designed to offer fiber advantages for mission-

critical networks like Telco/ISP backbones, cable operators, banking and enterprise

networks. It can reduce network downtime and increase Quality of Service levels.

065-1096 10/100/1000BaseT/TX TO 1000BaseSX/LX GIGABIT SFP MEDIA CONVERTER

2.2 Product Illustrations

Front Panel

Fiber SFP Slot LEDs Ethernet Port

Rear Panel

Power LED

2.3 DIP Switches

DIP 1 Enables / disables Link Fault Signaling (LFS)

DIP 2 N/A

DIP 3 N/A

DIP 4 N/A

DIP Switches Power Connecto

065-1096 10/100/1000BaseT/TX TO 1000BaseSX/LX GIGABIT SFP MEDIA CONVERTER

3 LED Indicators

This Device has LED indicators located at the front of the device. The LEDs have been

designed to give easy at-a-glance network status, and provide ‘real-time’ connectivity

information. Please see below for an interpretation of their functions:

LED Indicators

LED Condition Status

On (Green) Unit is receiving power

PWR Off Power off or failure

On (Green) Fiber link up

Flashing (Green) Data packets being transmitted or

received via Fiber port

LNK / ACT

Off Fiber link down

On (Green) 1000 Base Mode

1000 Off 10/100 Base Mode

On (Green) Copper link up

Port

LNK/ACT Flashing (Green) Data packets being transmitted or

received via Ethernet port

ALM On (Red) Any link failure or LFS

065-1096 10/100/1000BaseT/TX TO 1000BaseSX/LX GIGABIT SFP MEDIA CONVERTER

4 Installation

In this chapter, we will take a look at how to install the Converter within its operating

environment. To install your Media Converter, please see the following procedures:

•Location

•10/100/1000BaseT/TX port

•Gigabit SFP slot

•Link Fault Signaling

•Desktop installation

•Powering on unit

4.1 Location

The location selected for installing the Converter may greatly affect its performance.

When selecting a site, we recommend considering the following rules:

1. Install the Converter in a fairly cool and dry place. See Technical Specifications for

the acceptable temperature and humidity operating environments.

2. Install the Converter in a location free from strong electromagnetic field generators

(such as motors), vibration, dust, and direct exposure to sunlight.

3. Leave at least 10cm of space at the front and rear of the unit for ventilation.

4. Affix the provided rubber pads to the bottom of the Converter for grip, and to

protect the case from scratching.

4.2 10/100/1000BaseT/TX Port (RJ-45)

The auto MDI/MDI-X and auto-negotiation on the RJ-45 port alleviates the worry of

cabling configuration when connecting the Converter with a 10/100/1000Base-T device.

It accepts both ‘straight-through’ and ‘cross-over’ Ethernet cables without the need to

re-configure the port. Whether connecting to a switch, LAN card, or other network

device via the RJ-45 port, simply plug and go!

4.3 Gigabit SFP Slot

To connect a fiber cable’s connector to the Converter’s SFP slot, slide the selected

SFP module (mini-GBIC) into the SFP slot, making sure that the module’s receptors

line up with the receptors at the back of the slot. Push until you hear a click. Once the

module is inserted correctly, take the cable connector and turn it so that it will fit into

the mouth of the module. Then push the connector into the mouth until its catches click

into the receiving grooves in the module’s mouth. Use the appropriate type of multi-

mode or single-mode fiber, depending on the SFP module being used. The fiber optics

transmit data at up to 1000 Mbps and can maintain data integrity over cable distances

as long as 60 km or more, depending on the selected SFP (mini-GBIC) module.

Warning:

Because invisible laser radiation may be emitted from the aperture

of the fiber port when no cable is connected, avoid exposure to

laser radiation and do not stare into the open apertures.

065-1096 10/100/1000BaseT/TX TO 1000BaseSX/LX GIGABIT SFP MEDIA CONVERTER

4.4 Link Fault Signaling

LFS is an important function that is extremely beneficial in terms of network status

monitoring. The LFS function monitors both the copper and fiber segments to ensure

that Spanning Tree Protocol responds the moment a link failure occurs on either segment.

Set LFS to ON for normal operations.

Set LFS to OFF when installing cables or when testing the network connection.

Note: The LFS feature influences both fiber and copper segments. When disruption

occurs on the copper segment, the fiber segment will be disabled. When the fiber

segment loses signal, the copper segment will be disabled.

To utilize the full benefits of LFS, four converters can be used to build a primary and a

secondary path between two switches. The switches must support Spanning Tree or

Fast Spanning Tree protocols. By default, transmission of data will travel via the

primary path. If a link failure is detected, transmission will automatically be switched to

the secondary path by Spanning Tree Protocol, delivering non-stop network

connectivity.

4.5 Desktop Installation

Follow the instructions listed below to install the Converter in a desktop location.

1. Locate the Converter in a clean, flat and safe position that has easy access to AC

power.

2. Affix the four (4) self-adhesive rubber pads to the underside of the Converter.

3. Apply AC power to the Converter. (The green PWR LED on the rear panel should

light).

4. Connect cables from the network partner devices to the ports on the front panel.

(The green LNK LED on the front panel associated with the port should light).

This converter can also be mounted on a vertical surface.

Warning:

Please exercise caution when using power tools. Also, install this unit

away from damp or wet locations, or in close proximity to very hot

surfaces. These types of environments can have a detrimental effect on

the converter and cables. An ideal location is a lightly cooled place such

as a typical equipment room.

4.6 Powering On the Unit

The Converter uses an external power supply of 9~32V DC @ 0.5A – 50Hz to 60Hz.

1. Insert the power cable plug directly into its receptacle located at the back of the

device.

2. Plug the power adapter into an available socket.

3. Check the rear-panel LEDs as the device is powered on to verify that the Power

LED is lit. If not, check that the power cable is correctly and securely plugged in.

Tabla de contenidos

Otros manuales de Convertidor de medios de SignaMax

SignaMax

SignaMax 065-1196A Manual de usuario

SignaMax

SignaMax 065-1100NS Series Manual de usuario

SignaMax

SignaMax OAM Managed Dual Rate Converter Series Manual de usuario

SignaMax

SignaMax 065-1163T Manual de usuario

SignaMax

SignaMax 100BaseTX/FX to 100BaseFX Converter Series Manual de usuario

SignaMax

SignaMax 065-1800 series Manual de usuario

SignaMax

SignaMax 065-1895 series Manual de usuario

SignaMax

SignaMax FO-065-1195 Manual de usuario

SignaMax

SignaMax 065-1176 Instrucciones de funcionamiento

SignaMax

SignaMax 10/100TX to 100FX Manual de usuario

SignaMax

SignaMax F0-065-1200 Series Manual de usuario

SignaMax

SignaMax 065-1140 Multimode Manual de usuario

SignaMax

SignaMax I-1100 Series Manual de usuario

SignaMax

SignaMax 065-1197 Manual de usuario

SignaMax

SignaMax 065-1800 series Manual de usuario

SignaMax

SignaMax 100BaseTX/FX to 100BaseFX Converter Series Manual de usuario

SignaMax

SignaMax 100BaseTX/FX to 100BaseFX Converter Series Manual de usuario

SignaMax

SignaMax 065 Series Manual de usuario

SignaMax

SignaMax 065-1195SFP Manual de usuario

SignaMax

SignaMax 10/100/1000BaseT/TX to 1000BaseSX/LX Converter... Manual de usuario

SignaMax

SignaMax 065-1063FS Series Manual de usuario

SignaMax

SignaMax I-1100 Series Manual de usuario

SignaMax

SignaMax I-200 Series Manual de usuario

SignaMax

SignaMax Gigabit SFP Converter 065-1896SFPTB Manual de usuario

Manuales populares de Convertidor de medios de otras marcas

SoundTraxx

SoundTraxx Blunami BLU-2200 Manual de usuario

SPROLINK

SPROLINK VA1 Manual de usuario

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manual de usuario

Nikon

Nikon AF-S TC-20E III Manual de usuario

Axis

Axis AXIS Q7406 Manual de usuario

Omega

Omega TAC80B-J Manual de usuario

Zoom

Zoom Thunderbolt TAC-2R Manual de usuario

OST

OST iConverter 10/100M Manual de usuario

Vertiv

Vertiv Netsure Manual de usuario

birddog

birddog MINI Manual de usuario

Roland

Roland GI-10 Manual de usuario

Wallenstein

Wallenstein WX310 Manual de usuario

Pace

Pace MSS 200-1 Manual de usuario

Solar Converters

Solar Converters EQ 12/24-50 Manual de usuario

CYP

CYP EL-7400V Manual de usuario

TIE

TIE MIDI 1i1o Manual de usuario

DCS

DCS Vivaldi Upsampler Manual de usuario

Westermo

Westermo MCW-211 SERIES Manual de usuario