Canopy Side View
Cabinet Ceiling
Bracket
Back Panel
(Mounted to Bracket)
• Remove the back panel.
• Mount the angle bracket to the desired surface
(Fasteners Not Supplied).
• Mount the back panel to the angle bracket
(Fasteners Not Supplied).
• Hinge cabinet back and replace the screws that
were removed in step one on the reverse side.
• Remove the back panel.
• Mount the ceiling bracket to the desired surface
(Fasteners Not Supplied).
• Mount the back panel to the angle bracket
(Fasteners Not Supplied).
• Hinge cabinet back and replace the screws that
were removed in step one on the reverse side.
One bracket, two angles.
Custom angles available.
Fastener (Not Supplied)
Fastener (Supplied)
Wall
Side View
• Fasten the recessed mounting bracket flush with
the front of the LED traffic controller cabinet.
• Slide assembled unit into the recess opening.
• Fasten the mounting bracket to the face of the
opening with four fasteners (Fasteners Not Supplied).
TCI/L V/H 7½" x 14½" 10¾" x 17¾"
TCL 718 7½" x 18½" 10" x 21"
TCL 726 7½" x 26½" 10" x 29"
TCL 734 7½" x 34½" 10" x 37"
TCL 742 7½" x 42½" 10" x 45"
TCL 1418 14½" x 18½" 17" x 21"
TCL 1426 14½" x 26½" 17" x 29"
TCL 1434 14½" x 34½" 17" x 37"
TCL 1442 14½" x 42½" 17" x 45"
TCL 2118 21½" x 18½" 24" x 21"
TCL 2126 21½" x 26½" 24" x 29"
TCL 2134 21½" x 34½" 24" x 37"
TCL 2818 28½" x 18½" 31" x 21"
TCL 77 7½" x 7½" 10" x 10"
TCL 1026 10½" x 26½" 13" x 29"
TCL 1212 12½" x 12½" 15" x 15"
TCL 1818 18½" x 18½" 21" x 21"
• Lay post(s) on ground, slide cabinet with
mounting extrusion attached into the post slot.
• Align the cabinet flush with top of the post(s).
• Tighten the set screw in the mounting extrusions
and fasten the post cap on the post(s).
• Level the sign both horziontally and vertically.
TCL1013 KAM
Sign
Cabinet
Recessed
Frame
Wall Opening
Sign Cabinet
Standard
Post
Mounting
Extrusion
Set
Screw
Note: Make appropriate wiring
connections per local codes.
Note: Do not over-tighten
fasteners or distort back panel.
Note: Clear all metal chips
from inside sign cabinet,
failure may void warranty.
Note: Make appropriate wiring
connections per local codes.
Note: Do not over-tighten
fasteners or distort back panel.
Note: Make appropriate wiring
connections per local codes.
Note: Do not over-tighten
fasteners or distort back panel.
Note: Clear all metal chips
from inside sign cabinet,
failure may void warranty.
Note: Make appropriate wiring
connections per local codes.
Note: Clear all metal chips
from inside sign cabinet,
failure may void warranty.
Canopy
Top View
Cabinet
30º
45º
Ceiling Mount
Install Instructions
Recessed Frame Mount
Install Instructions
Dual Angle Mount
Install Instructions
Center/Double Post Mount
Install Instructions
Wall Mount
Back Dimensions
7/8" Diameter knockout
for conduit
(4) 1/4" Diameter knockouts
for mounting
D
Ø 7/8"
Ø 1/4"
B
C
C
Back View
A
Cabinet
High x Wide
Dimension A
Mounting Hole (Vert)
Dimension B
Center Knock-out (Vert)
Dimension C
Mounting Hole (Horz)
Dimension D
Center Knock-out (Horz)
7x 75½" 1¼"
7 x 18 5½" 1¼"
7 x 26 5½" 1¼"
7 x 34 5½" 1¼"
7 x 42 5½" 1¼"
10 x 26 10½" 1¼"
12 x 12 12½" 1¼"
14 x 18 14½" 1¼"
14 x 26 14½" 1¼"
14 x 34 14½" 1¼"
14 x 42 14½" 1¼"
18 x 18 18½" 1¼"
Cabinet
Model Size
Wall Opening
Dimensions
Bracket
Outer Dimensions
