SignalSys SP200XV2 Manual de usuario

SP200XV2 User’s Manual

Version 3.2.x

SignalSys, Inc.

www.SignalSys.com

Index

I. Introduction ……………………………...4

1.1 SP200X Production introduction

1.2 Safety Precaution

II. LAN Configuration ……………………………….4

2.1 LAN Interface Settings

2.2 DHCP Ser er Settings

2.3 Routing Settings

2.4 Port Forwarding (NAPT) Settings

2.5 VLAN Settings

III. Ethernet WAN Configuration ……………………………….8

3.1 WAN Interface Status

3.2 WAN Interface Settings

3.3 Ethernet WAN PPPoE Settings

3.4 IPSEC Configuration

3.5 VLAN Settings

3.6 MAC Spoofing

IV. SIP Configuration …………………………….…13

4.1 SIP Settings

4.2 SIP Extensions

4.3 Out-of-band (OOB) Signalling Settings

4.4 SIP ToS/DiffSer Settings

4.5 SIP VLAN Settings

V. CODEC Configuration ………………………………16

VI. System Configuration ………………………………17

6.1 Security Settings

6.2 Localization / Clock Settings

6.3 SNMP Settings

6.4 Ser ice Access Settings

VII. Do nload Configuration ………………………………19

VIII. Reset Configuration ………………………………19

IX. General Troubleshooting ………………………………20

9.1 LED

9.2 Mass Deployment

X. Make Phone Calls ………………………………20

10.1 Make a Call

10.2 3-Way Conference

10.3 Call Waiting

10.4 Call Forwarding

Appendix: ………………………………21

A. Determining the IP Address

A.1 General Instructions

B. Forcing ‘Safe’ Modes

C. Dial Plans

C.1 Sample Dial Plans

SECTION I. Introduction

1.1 SP200X Production Introduction

SP200X VoIP Media-Router pro ides the perfect solution for broadband Internet

sharing and Voice o er IP. It allows multiple PCs to share one high-speed Broadband

(Cable/DSL) Internet connection. It also pro ides one analog telephone port, which

allows the user to make calls on the Internet or regular telephone line around the world.

The built-in NAT technology acts as a firewall and protects your internal network. The

VPN (Virtual Pri ate Network) pass-through protects your data when it tra els on the

Internet. The built-in DHCP ser er dynamically assigns the IP address for your LAN

(local area network).

It is easy to make phone calls using SP200X. You just need to plug the standard

telephone into the telephone port of SP200X. You need no sound cards, modems,

speakers and microphones. None of your PCs e en ha e to be turned on to make and

recei e calls.

1.2 Safety Precaution

Read these Safety Precautions carefully before you install the SP200X

• Read the User Manual before using the SP200X

• Keep your User Manual in a safe place

• Pay attention to all remarks with warning marks

• Check the power oltage in your area

• Make sure the power plug is not o er burdened, which may cause equipment damage

and fire

• Keep power cord standard wiring. Do not put anything on it

• Keep the equipment in a cool place

• Do not use other accessories that are not pro ided in your package

• Pre ent thunder damage to the de ice. During thunderstorms, please UN-PLUG the

power cord

• Do not disassemble the de ice

• Be careful of the adapter when un-plugging the power cord

• Make sure the power switch in turned OFF before you PLUG-IN/UNPLUG the cord

• Do not connect the SP200X to wall jacket

•

Do not connect SP200X with PBX without help of technical support engineer

SECTION II.

LAN Configuration

The de ice supports bridging/routing, the main menu LAN option pro ides sub-pages to

configure the pri ate LAN settings. There are fi e sub-pages to allow iewing of the LAN

interface status and configuration of pri ate internal DHCP settings, routing settings and the port

forwarding (NAPT) settings. Please note that any actions/modifications which alter the topology

of the Ethernet bridge will result in the Ethernet bridge spanning tree protocol requiring to

relearn. During this relearn period (may take up to one minute), HTTP access will be una ailable

on all bridged interfaces (including the LAN interface).

2.1 LAN Interface Settings

This sub-page allows the user to configure the pri ate LAN interface settings.

Assign an IP address to the LAN Ethernet port. This IP address is also the default router address

for the de ices on the pri ate LAN. The default LAN interface IP address is set to 192.168.123.1.

Enter the subnet mask for the pri ate LAN.

If you wish to set the broadcast and multicast limits for the bridge/router, enter these alues as

percentages of the LAN interface Ethernet bit rate. Lea ing these alues blank will imply alues

of 100%.

Press "Sa e LAN Settings" to sa e and apply the LAN interface settings. Any new settings will

take effect immediately.

2.2 DHCP Server Settings

This sub-page allows configuration of the pri ate LAN DHCP ser er. The DHCP ser er settings

do not apply if the de ice is operating in bridge only mode.

Specify whether the de ice’s internal DHCP ser er feature is enabled or disabled. Also indicate

the IP address range to use for DHCP assignments to the LAN. Specify the domain name

(optional) that is pro ided to LAN clients ia DHCP. Two optional static DNS ser er IP

addresses can be entered that will be pro ided to LAN clients ia DHCP. These are in addition to

the DNS ser ers automatically pro ided by WAN connections. Press "Sa e DHCP Settings" to

sa e and apply the DHCP ser er settings. Any new settings will take effect immediately.

In addition, up to eight static DHCP address assignments can be configured. To add a static IP

assignment, enter the LAN de ice’s name (must be unique in the pri ate network) and/or MAC

address. Specify the static IP to be assigned and press the "Add" button. To remo e an existing

entry, press the "Remo e" button next to the entry to be remo ed.

To iew the current acti e DHCP client binding table (the internal list of de ices for which the

ser er has pro ided an IP address lease), press "View DHCP Table". A popup window will

appear displaying the list of bindings. Press "Update" to update the binding information. Press

"Close" to close the binding table window. To clear the de ice’s internal DHCP client binding

table, press "Clear client binding table". Be aware that doing this will destroy the DHCP ser er’s

knowledge of the LAN clients it has pro isioned, and may result in client problems when a client

tries to renew its lease.

2.3 Routing Settings

This sub-page allows configuration of the de ice’s core router functionality. The router settings

do not apply if the de ice is operating in bridge only mode.

If you wish for the router to dynamically update its routing tables, specify whether RIP 2

dynamic routing information is to be recei ed or transmitted (or both). Press "Sa e Router

Settings" to sa e and apply the dynamic routing settings. Any new settings will take effect

immediately.

In addition, up to eight static route entries can be assigned. To add a static route, enter the static

route Destination IP Address, Subnet Mask, Gateway IP Address, Metric, and Interface, and press

the "Add" button. Metric is a number from 1 to 15 inclusi e. To remo e a static route, press the

"Remo e" button next to the entry you wish to remo e.

To iew the de ice’s current internal routing table, press the "View Routing Table" button. A

popup window will appear displaying the routing table. Press "Update" to update the route

entries. Press "Close" to close the routing table window.

2.4 Port For arding (NAPT) Settings

This page allows the user to customize the de ices port forwarding feature. The port forwarding

feature does not apply if the de ice is operating in bridge only mode.

Port forwarding pro ides WAN access to the internal LAN, by specifying that traffic o er certain

ports are to be directed at particular LAN hosts. This feature is a ailable only in router mode. Up

to eight port forwarding entries ("Pinholes") can be configured. To add a port forwarding entry,

configure the Port Range to be forwarded, the Protocol to be forward (TCP, UDP or both), and

destination LAN IP Address. Press the "Add" button to add the entry. To remo e an existing

entry, click the "Remo e" button next to that entry you wish to remo e.

Note that certain port numbers may be reser ed by the SP200X for its own internal use. These

ports may not be used for port forwarding to the LAN. Ports which may be reser ed by the

SP200X include those used by VoIP call signaling, RTP packets, HTTP and SNMP. All reser ed

(una ailable) ports will be displayed on this page.

2.5 VLAN Settings

The LAN sub-page allows the user to configure general VLAN settings for all packets

originating from the LAN interface. Howe er, specific VLAN settings for VoIP call signaling

and RTP packets can be separately applied (see sections 3.5), which will o erride the general

alues set on this page. If no special VoIP call signaling or RTP VLAN settings are applied, then

call signaling and RTP packets will also use the general VLAN settings entered on this page.

Press "Sa e VLAN Settings" to sa e and apply the general VLAN settings. Any new settings

will take effect immediately.

*DO NOT CHANGE THIS VLAN SETTINGS UNLESS YOU KNOW EXACTLY WHAT

YOU WANT TO DO

SECTION III.

Ethernet WAN Configuration

This page and its sub-pages are only a ailable on SP200X de ice, which support routing/bridging

and allow iewing and configuration of the WAN interface status/settings.

Please note that any actions/modifications which alter the topology of the Ethernet bridge will

result in the Ethernet bridge spanning tree protocol requiring to relearn. During this relearn period

(may take up to one minute), HTTP access will be una ailable on all bridged interfaces (including

the LAN interface).

3.1 WAN Interface Status

This page displays the current status of the WAN interface, including the IP address and other

network settings the interface is currently using. If the interface is configured for PPPoE, a button

is a ailable to allow the administrator to DISCONNECT an acti e WAN PPPoE session or to

initiate (CONNECT) a PPPoE session (if currently disconnected).

3.2 WAN Interface Settings

This sub-page only applies to the SP200X de ice. It allows the user to configure the Ethernet

WAN interface. First, select whether the de ice is to act as a router or a bridge between the WAN

and LAN interfaces.

Select whether you wish for the WAN interface to be configured dynamically ( ia a DHCP

ser er on the network if Ethernet, or ia PPP if using PPPoE), or statically configured.

you wish to statically assign the WAN interface settings, enter the IP address, subnet mask,

default gateway IP address and DNS ser er IP address. It is also recommended that the network

domain name be pro ided as well, to ensure correct DNS operation.

Press "Sa e WAN Settings" to sa e and apply the new alues. Any new settings will take effect

immediately.

3.3 Ethernet WAN PPPoE Settings

On this sub-page you can specify whether the WAN interface is to use PPPoE, and configure the

PPPoE client. First, select whether PPPoE is enabled or disabled. If enabled, enter the username

and password required for the login (authentication) process.

Setting the idle-timeout will result in the PPP connection being torn down if the client detects

inacti ity on the connection o er the specified timeout period. Lea ing this field blank will result

in the connection being permanently up (i.e. without timeout).

If the PPPoE ser er (ser ice pro ider) requires any special Ser ice Name or AC Name to be set,

you can specify these tags here.

Press "Sa e PPPoE Settings" to sa e and apply the WAN interface PPPoE client settings. Any

new settings will take effect immediately.

Tabla de contenidos

Manuales populares de VoIP de otras marcas

Minitar

Minitar MVA11A Manual de usuario

3Com

3Com VCX V7122 SIP Manual de usuario

Fanvil

Fanvil D800 Manual de usuario

ZyXEL Communications

ZyXEL Communications FMG3024-D10A Series Manual de usuario

WELLTECH

WELLTECH ATA-171 - V2.0 Manual de usuario

WELLTECH

WELLTECH ATA-171 - V1.6 Manual de usuario

Aastra

Aastra AastraLink Pro 160 Manual de servicio

CyberData

CyberData 011149 Series Manual de usuario

SM VVX 350 Manual de usuario

Sipura Technology

Sipura Technology SPA-2002 Manual de usuario

Avaya

Avaya IP Office Phone Manager Manual de usuario

D-Link

D-Link DVX-1000 Manual de usuario

NetComm

NetComm V110 Manual de usuario

XtendLan

XtendLan GONU14RS Manual de usuario

ATCOM

ATCOM MP01 Manual de uso y cuidado

Aastra

Aastra X Series Manual de usuario

Allied Telesis

Allied Telesis AT-VP504E FXS Manual de instrucciones

iPECS

iPECS eMG80 Instrucciones de funcionamiento e instalación