SIGNALSYNC SDVR-PRO1004 Manual de usuario
4CH Digital Video Recorder
User’s Manual
SDVR-PRO1004
November, ‘2004
SAFETY PRECAUTIONS
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This label may appear on the rear of the unit due to space limitations.
The lightning flash with arrow point symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of importance operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
Warning
To reduce the risk of fire or electric shock, Do not expose this product to rain or moisture.
Do not insert any metallic object through ventilation grills.
Power disconnect : Units with or without ON-OFF switches have power
supplied to the unit whenever the power cord is inserted into the main source;
However, the unit is operational only when the ON-OFF switch is in the ON
position. To disconnect it from the main source, you have to disconnect the
Power cord.
FCC COMPLIANCE STATEMENT
A CLASS A computing device subject to certification by the Commission shall be identified pursuant to
Par 2.925 et Seq of the chapter. In addition, the label shall include the following statement:
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received,
including interference that may cause undesired operation.
Where a device is constructed in two or more sections connected by wires and marked together, the
statement specified in this Section is required to be affixed only to the main control unit.
The users manual or instruction manual for the EUT shall contain the following statement or equivalent.
Caution : Changes or Modifications not expressly approved by the party responsible for compliance could
void the users authority to operate the equipment.
If the EUT requires accessories such as special shield cables and/or connectors to enable compliance
with emission limits, the instruction manual for the EUT shall include appropriate instruction on the first
page of the text concerned with the installation of the device that these special accessories must be used
with the device. It is the responsibility of the user to use the needed special accessories supplied with the
equipment.
For a CLASS A digital device or peripheral, the instruction furnished the user shall include the following or
Similar statement placed in a prominent location in the text of the manual.
Note : This equipment has been tested and found to comply with the limits for a CLASS a digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment, This equipment
Generates, uses and can radiate radio frequency energy and, if not in stalled and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of the
this equipment in a residential area is likely to cause harmful interference in which cause the user will
be required to correct the interference at his own expense.
Before Starting Your DVR Operation
This document is a basic manual for the SIGNALSYNC DVR users.
This manual describes the appearance and name of products, how to configure the
system program, and how to use the system.
Before using SIGNALSYNC DVR, a user should read the contents of user manual, and
then deal with the product considering the precautions defined in the manual.
To open the system case and touch the inner parts for corrective maintenance, a user
should contact the place where he/she purchased the products to get the help from
expert.
In addition, if there is any question for use or any damage on the product, please contact
call the place where he/she purchased the products.
Precautions for safety (User should observe)
1. Precautions for installation
zInstall the product on a flat floor not closed and retain the distance of more than 15
cm from the rear panel to the wall.
zInstall the product on a well-ventilated place.
zKeep it away from strong magnetism or electromagnetic wave.
zInstalling it near radio equipment such as TV and radio may cause a fault.
zDo not install it on a place that is exposed directly to the sun or contains lots of heat
such as near a heating apparatus.
zDo not install it on a cold place.
zPlace the equipment or tools in the site remote from a busy road so that people are
not hurt.
zDo not install it on a place where there is severe vibration, much humidity or soot.
zShould use the product in the rated voltage (The equipment is used as both 110V
and 220V, but it is set to 220V for delivery. It is possible to adjust it with the
changeover switch on the rear panel.)
zConnect it to the outlet with the ground terminal.
zDiscard the plastic bag well. (It is dangerous to put it on the head.)
2. Precautions for use
zFor the repair, contact the company or the place where you purchased the product.
zRead the user manual before using the product.
zDo not open the cover at your discretion because there are parts sensitive to the
environment within the equipment.
zArrange the power cord safely and do not touch it with wet hands.
zDo not use a loose outlet or a damaged power cable.
zDo not use benzene, thinner and alcohol for cleaning. They may deform the product.
zDo not touch the exposed terminal.
zFor the power-off of system, normally turn off the power of the program and then,
power off the peripherals. (Do not power it off with the power button on the front panel
of body.)
zBe careful to prevent a conductive object from falling into a hole that was punched for
ventilation.
zDo not dissemble and remodel the product.
zDo not place a heavy thing on the body.
zDo not give a shock during the movement of equipment.
zIf you use the product in the state of smoke or smell emitted, it may cause a fire or an
electric shock. For this case, immediately block the power switch and contact the
company or the place where you purchased the product to consult it with a special
technician.
Table of Contents
I. Introduction
1. Package Contents
2. Features
3. Front Panel and Rear Panel Connection
II. Installation
1. Front Panel
2. Rear Panel
3. Menu Tree
III. Main MENU Programming
1. Overview Main Menu
2. SYSTEM SETUP
3. DISPLAY SETUP
4. RECORDING SETUP
5. ALARM SETUP
6. MOTION SETUP
7. WEEKLY SETUP
8. NETWORK SETUP
9. ARCHIVING
10. HDD INFORMATION
11. SEARCH LIST
12. DISPLAY Mode
13. RECORDING Mode
14. PLAYBACK Mode
IV. Viewing USB archiving image
V. Remote NetViewer Program Installation
APPENDIX 1. Specification
2. Pin Description of connectors
I. Introduction
1. Package Content
When purchasing SIGNALSYNC product, unpack it at first and unload it on a flat
floor or a place where it is to be located. Then, verify that the following contents are
contained.
z4CH DVR
zPower code
zRack Mount Bracket
zUser’s manual
zInstall CD
4CH DVR
Power Code Rack Mount Bracket Install CD
User’s Manual
2. Features
This DVR provides recording capabilities for four camera inputs. It provides playback
or live display and network function while in recording mode. And also it offers the
following features:
4 Composite Input Connectors/ 4 Loop-Through Video Connectors
-Compatible with Color (NTSC or PAL) and B&W (CCIR and EIA-170) Video
Display and Record Video Resolution
- NTSC (720x480), PAL (720x576)
- Single, QUAD, Sequential Image Display
- 4CH multiplexing video recording with 720x480 resolution (NTSC)
Compression: M-JPEG
-Standard image, high quality; 16KB / field
Multiple Search Engines (Date/Time, Event)
Records up to 60 NTSC IPS (50 PAL Images per Second)
Continuous Recording in Disk Overwrite Mode
Simultaneously Record, Playback and Network
Archiving using USB Memory Drive
- USB 1.1 Storage Class support
User-friendly Graphical User Interface (GUI)
Manual/ Schedule and alarm/ motion recording Modes (Time and Event)
Alarm input Connections, relay output connection
Network Function
-Dynamic IP (DHCP, Floating IP) support
- Live or Recorded Video Access via Ethernet
Audio Recording and Playback
- 1ch audio support
3. Front Panel and Rear Panel Connection
Power
Code
Sensor
Input
Monitor
Audio
Out
Audio
Input
Alarm
Output
LAN
(Ethernet)
Cameras RS485
(RTZ Camera)
USB Memory
Drive
RS232C
II. INSTALLATION
Front Panel
1 2 3 4 5 6 7 8 9 10 11 12
1. USB port
A USB port is provided to connect external USB memory drive for archiving video.
2. Archiving button
Whenever ARCHIVE button is pressed, archiving will be started.
3. REC/ STOP button
Press REC (Red circle) to begin record. Press REC to stop recording again. This is
toggle button.
4. PLAY/ STOP button (▶)
If PLAY/ STOP is pressed, search lists will be displayed to begin playback. After
selecting one recorded file, playback will be started by PLAY/ STOP button.
5. FF (▶▶)
Press FF to perform high speed forward playback.
6. REW (◀◀)
Press REW to perform high speed backward playback.
7. PAUSE
Press PAUSE to pause playback.
NOTE: Still image will be displayed. For single image forward in PAUSE, PAUSE
button can be pressed.
8. MENU/ ESC
Press MENU/ESC button to enter menu system. Also MENU/ESC is used to escape
upper menu and to save set-up parameter at the same time .
9. QUAD/ SEQ
This button is used for QUAD, sequential display. It is rotated as QUADÆSequential
ÆQUAD.
Tabla de contenidos
