Sigma Designs ZIRC Manual de usuario

USER MANUAL

ZIRC

All information are correct at the time of release. Sigma Designs owns the proprietary rights to the information contained herein this document. It may not e

edited, copied or circulated without prior written agreement y Sigma Designs.

ZIRC

Z-Wave/Infra-Red Audio Video Remote Control

User Manual

Version 1.1

USER MANUAL

ZIRC

All information are correct at the time of release. Sigma Designs owns the proprietary rights to the information contained herein this document. It may not e

edited, copied or circulated without prior written agreement y Sigma Designs.

CONTENTS

QUICK START GUIDE 3

Using ZIRC in Z-Wave Mode with STB.......................................................................................................3

Using ZIRC in Infra-Red Mode with STB ....................................................................................................3

INTRODUCTION 4

SYMBOLS 5

RESET TO FACTORY DEFAULT 6

LEARN INTO A NETWORK 7

UPDATE ASSOCIATION 8

SWITCHING BETWEEN Z-WAVE AND INFRA-RED MODES 9

Switching ZIRC from Z-Wave Mode to IR Mode .......................................................................................9

Switching ZIRC from IR Mode to Z-Wave Mode .......................................................................................9

STATUS INDICATORS 10

TEST MODES 11

Carrier Frequency ...................................................................................................................................11

Modulated Signal ....................................................................................................................................12

FCC NOTICE TO USERS 13

USER MANUAL

ZIRC

All information are correct at the time of release. Sigma Designs owns the proprietary rights to the information contained herein this document. It may not e

edited, copied or circulated without prior written agreement y Sigma Designs.

QUICK START GUIDE

Using ZIRC in Z-Wave Mode with STB

Step 1. Ena le STB Z-Wave Add-Node (refer to STB User Manual)

Step 2. Insert 2 x AAA atteries into ZIRC.

ZIRC in Factory Default state will e Z-Wave Learn Mode once attery is

inserted.

Step 3. Wait for indication.

GREEN Light flashes 3 times indicating Successful operation.

X 3

Flashes 3 times for Successful operation

RED Light flashes 3 times indicating Fail operation.

X 3

Flashes 3 times for Fail operation

If operation fail, RESET ZIRC to Factory Default (refer to section “RESET

TO FACTORY DEFAULT”), and repeat Step 1 to 3 in this section.

Using ZIRC in Infra-Red Mode with STB

Step 1. Insert 2 x AAA atteries into ZIRC.

Step 2. Press-and-Hold SETUP and RED for 5 sec

Step 3. Wait for indication.

GREEN Light flashes 1 times indicating Successful operation.

X 1

Flashes 1 time for Successful operation

Step 4. YELLOW Light flashes 1 times with any key pressed on ZIRC indicating

ZIRC is in Infra-Red Mode.

X 1

Flashes 1 time for any key pressed

indicating ZIRC is in Infra-Red Mode

USER MANUAL

ZIRC

All information are correct at the time of release. Sigma Designs owns the proprietary rights to the information contained herein this document. It may not e

edited, copied or circulated without prior written agreement y Sigma Designs.

INTRODUCTION

ZIRC is a Z-Wave

ena led Remote Control. ZIRC is mainly to e used as the AV (Audio Video)

remote control for a Sigma Designs Media SetTop Box which is also supporting Z-Wave

;

allowing user to remotely control the SetTop Box using RF instead of the conventional infra red

technology. Having said that, ZIRC also supports Infra-red remote feature; demonstrating the

uild-in IR ready feature of Z-Wave 400 series chip set.

Besides controlling Sigma Designs Media SetTop Box, ZIRC is also compati le with any Z-Wave

ena led network and devices (supporting AV Command Class) from a range of manufacturers.

Z-Wave is an interopera le two way RF mesh networking technology.

Figure 1 ZIRC Z-Wave / Infra-Red Rem te C ntr l

ZIRC is adopting an old casing of a Sigma Designs Infra-Red (IR) Remote Control to demonstrate

the possi ility of converting an existing IR remote control to a Z-Wave

ena led Remote

Control. ZIRC also retain the infra-red capa ility, in which it can e used to remote control

older series of Sigma Design Set Top oxes supporting only the conventional infra-red remote

control.

Figure 2 Sigma Design C nventi nal IR Rem te C ntr l & ZIRC (Z-Wave / IR Rem te C ntr l)

USER MANUAL

ZIRC

All information are correct at the time of release. Sigma Designs owns the proprietary rights to the information contained herein this document. It may not e

edited, copied or circulated without prior written agreement y Sigma Designs.

SYMBOLS

The following sym ols are used in this document:

Flashing Green Light

Flashing Red Light

Flashing Yellow Light

Press-and-Hold Button 1 for 5 sec

Press-and-Hold

Button 1 & Button 2 for 5 sec

Press-and-Hold Button 1, Button 2,

Button 3 & Button 4 for 10 sec

USER MANUAL

ZIRC

All information are correct at the time of release. Sigma Designs owns the proprietary rights to the information contained herein this document. It may not e

edited, copied or circulated without prior written agreement y Sigma Designs.

RESET TO FACTORY DEFAULT

When set to Factory Default state, ZIRC is not in any network and is in Z-Wave mode. This

feature is generally used to remove ZIRC from its existing network.

Step 1. Press-and-Hold SETUP and INFO for 10 sec

Step 2. Wait for indication.

GREEN Light flashes 3 times indicating Successful operation. ZIRC is now

set to Factory Default.

Flashes 1 time for Successful operation

Step 3. ZIRC is now ready to Learn into a new network. It will transmit up to 17

Frames of Node Info Frame continuously and then stop transmitting.

ZIRC will again transmit up to 17 Frames of Node Info with any key

pressed.

Note:

If ZIRC is not in a network OR in factory default, re-inserting attery OR any key pressed with

activate or deactivate Learn Mode where Node Info will e transmitted continuously. ZIRC will

stop transmitting Node Info if:

-it successfully learned into a successfully, or

-any key is pressed to stop Inclusion Mode, or

-up to 17 frames of Node Info has een transmitted.

USER MANUAL

ZIRC

All information are correct at the time of release. Sigma Designs owns the proprietary rights to the information contained herein this document. It may not e

edited, copied or circulated without prior written agreement y Sigma Designs.

LEARN INTO A NETWORK

Before ZIRC can e used to control a STB, it needs to e added into the STB Z-Wave network.

Step 1. Reset ZIRC to Factory Default (Refer to “RESET TO FACTORY DEFAULT”).

Remove Battery (removing attery is optional).

Step 2. Ena le STB Z-Wave Add-Node (refer to STB User Manual)

(a) Insert 2 x AAA atteries into ZIRC.

ZIRC in Factory Default state will e Z-Wave Learn Mode once attery is

inserted.

( ) Press any key to activate / de-activate Z-Wave Learn Mode

Step 3. Wait for indication.

GREEN Light flashes 3 times indicating Successful operation.

X 3

Flashes 3 times for Successful operation

RED Light flashes 3 times indicating Fail operation.

X 3

Flashes 3 times for Fail operation

If operation fail, RESET ZIRC to Factory Default (refer to section RESET TO

FACTORY DEFAULT), and repeat Step 1 to 3 in this section.

USER MANUAL

ZIRC

All information are correct at the time of release. Sigma Designs owns the proprietary rights to the information contained herein this document. It may not e

edited, copied or circulated without prior written agreement y Sigma Designs.

UPDATE ASSOCIATION

STB may create associations with other STBs using Z-Wave network features to allow

simultaneous control from a single ZIRC.

To support this feature, ZIRC will o tain this information (if any) from its current STB.

Step 1. Press-and-Hold SETUP and YELLOW for 5 sec.

Flashes 3 times for Successful operation

Step 4. Wait for indication.

GREEN Light flashes 3 times indicating Successful operation.

X 3

Flashes 3 times for Successful operation

RED Light flashes 3 times indicating Fail operation.

X 3

Flashes 3 times for Fail operation

If operation fails, repeat from Step 1 to 4 in this section.

USER MANUAL

ZIRC

All information are correct at the time of release. Sigma Designs owns the proprietary rights to the information contained herein this document. It may not e

edited, copied or circulated without prior written agreement y Sigma Designs.

SWITCHING BETWEEN Z-WAVE AND INFRA-RED MODES

The Infra- Red standard supported y ZIRC is NEC format with address of 0xCB04.

Switching ZIRC from Z-Wave Mode to IR Mode

Step 1. Press-and-Hold SETUP and RED for 5 sec

Step 2. Wait for indication.

GREEN Light flashes 1 times indicating Successful operation.

X 1

Flashes 1 time for Successful operation

Step 3. YELLOW Light flashes 1 times with any key pressed on ZIRC indicating

ZIRC is in Infra-Red Mode.

X 1

Flashes 1 time for any key pressed

indicating ZIRC is in Infra-Red Mode

Switching ZIRC from IR Mode to Z-Wave Mode

Step 1. Press-and-Hold SETUP and RED for 5 sec

Step 2. Wait for indication.

GREEN Light flashes 1 times indicating Successful operation.

X 1

Flashes 1 time for Successful operation

Step 3. GREEN OR RED Light flashes 1 times with any key pressed on ZIRC

indicating ZIRC is in Z-Wave Mode

X 1

GREEN Flashes 1 time for any key pressed

indicating success in Z-Wave communication

RED Flashes 1 time for any key pressed

indicating failure in Z-Wave communication

USER MANUAL

ZIRC

All information are correct at the time of release. Sigma Designs owns the proprietary rights to the information contained herein this document. It may not e

edited, copied or circulated without prior written agreement y Sigma Designs.

STATUS INDICATORS

The light indicator on ZIRC provides the following information

Event Light Indicator Description

IR Mode ZIRC is in IR Mode

Test Mode … Test Mode is in progress

Z-Wave network operation is successful

Z-Wave network

management activities:

(a) Learn into network

( ) Update Association Z-Wave network operation is successful

ZIRC successfully control STB through Z-