SIGLENT SDS1000 Series Manual de usuario

SDS1000 Series

SDS-RCM 1

Remote Control

Manual SDS1000

Series

Oscilloscopes

SIGLENT TECHNOLOGIES CO., LTD

RC01011-E02B

SDS1000 Series

2 SDS-RCM

catalogue

Using Status Registers ..................................................................................................... 3

About these Commands & Queries ................................................................................. 3

How they are listed? .................................................................................................... 3

How they are described?.............................................................................................. 3

When can they be used? .............................................................................................. 4

Command Notation .......................................................................................................... 4

Table of Commands & Queries....................................................................................... 5

Commands & Queries.................................................................................................... 11

Index.............................................................................................................................. 130

SDS1000 Series

SDS-RCM 3

Using Status Registers

A wide range of status registers allows the oscilloscope’s internal processing status to be

determined quickly at any time. These registers and the instrument’s status reporting system are

designed to comply with IEEE 488.2 recommendations. Following an overview, starting this

page, each of the registers and their roles are described.

Related functions are grouped together in common status registers. Some, such as the Status

Byte Register (STB) or the Standard Event Status Register (ESR), are required by the IEEE

488.2 Standard. Other registers are device-specific, and include the Command Error Register

(CMR) and Execution Error Register (EXR). Those commands associated with IEEE 488.2

mandatory status registers are preceded by an asterisk <*>.

About these Commands & Queries

This section lists and describes the remote control commands and queries recognized by the

instrument. All commands and queries can be executed in either local or remote state.

The description for each command or query, with syntax and other information, begins on a new

page. The name (header) is given in both long and short form at the top of the page, and the

subject is indicated as a command or query or both. Queries perform actions such as obtaining

information, and are recognized by the question mark (?) following the header.

How they are listed?

The descriptions are listed in alphabetical order according to their long form. Thus the

description of ATTENUATION, whose short form is ATTN, is listed before that of AUTO

SETUP, whose short form is ASET.

How they are described?

In the descriptions themselves, a brief explanation of the function performed is given. This is

followed by a presentation of the formal syntax, with the header given in Upper-and-Lower-

SDS1000 Series

4 SDS-RCM

Case characters and the short form derived from it in ALL UPPER-CASE characters. Where

applicable, the syntax of the query is given with the format of its response.

When can they be used?

The commands and queries listed here can be used with SDS1000 Series digital instruments.

Command Notation

The following notation is used in the commands:

< > Angular brackets enclose words that are used as placeholders, of

which there are two types: the header path and the data parameter

of a command.

: = A colon followed by an equals sign separates a placeholder from

the description of the type and range of values that may be used in

a command instead of the placeholder.

{} Braces enclose a list of choices, one of which one must be made.

[ ] Square brackets enclose optional items.

… An ellipsis indicates that the items both to its left and right may be

repeated a number of times.

As an example, consider the syntax notation for the command to set the vertical input sensitivity:

<channel> : = {C1, C2, C3, C4}

<v_gain>: = 2 mV to 5 V

The first line shows the formal appearance of the command, with <channel> denoting the

placeholder for the header path and <v_gain> the placeholder for the data parameter specifying

the desired vertical gain value. The second line indicates that one of four channels must be

chosen for the header path. And the third explains that the actual vertical gain can be set to any

value between 2 mV and 5 V.

SDS1000 Series

SDS-RCM 5

Table of Commands & Queries

Short Form

Long Form Subsystem What the Command or

Query Does

ALST? ALL_STATUS? STATUS

Reads and clears

the contents of all

status registers.

ARM ARM_ACQUISITION ACQUISITION

Changes acquisition state

from “stopped” to

“single”.

ATTN ATTENUATION ACQUISITION

Selects the vertical

attenuation factor of the

probe

ACAL AUTO_CALIBRATE MISCELLANEOUS Enables or disables

automatic calibration.

ASET AUTO_SETUP ACQUISITION Adjusts vertical, time base

and trigger parameters.

AUTTS AUTO_TYPESET ACQUISITION Selects the display type of

automatic setup.

AVGA AVERAGE_ACQUIRE

ACQUISITION Selects the average times

of average acquisition.

BWL BANDWIDTH_LIMIT ACQUISITION

Enables/disables the

bandwidth-limiting low-

pass filter.

BUZZ BUZZER MISCELLANEOUS Controls the built-in

piezo-electric buzzer.

*CAL? *CAL? MISCELLANEOUS

Performs complete

internal calibration of the

instrument.

CHDR COMM_HEADER COMMUNICATION Controls formatting of

query responses.

*CLS *CLS STATUS Clears all status data

registers.

CMR? CMR? STATUS

Reads and clears the

Command error Register

(CMR).

CONET COMM_NET COMMUNICATION

Specifies network

addresses of scope and

printers.

CPL COUPLING ACQUISITION Selects the specified input

channel’s coupling mode.

SDS1000 Series

6 SDS-RCM

CRMS CURSOR_MEASURE CURSOR

Specifies the type of

cursor/parameter

measurement.

CRST? CURSOR_SET? CURSOR Allows positioning of any

one of eight cursors.

CRVA? CURSOR_VALUE? CURSOR

Returns trace values

measured by specified

cursors.

CRAU CURSOR_AUTO CURSOR Changes the cursor mode

to auto mode.

CSVS CSV_SAVE SAVE/RECALL

Saves specified waveform

data of CSV format to

USB device.

COUN COUNTER FUNCTION

Enables or disables the

cymometer to display on

the screen.

CYMT CYMOMETER FUNCTION

Returns the current

cymometer value which

displaying on the screen.

DATE DATE MISCELLANEOUS

Changes the date/time of

the internal real-time

clock.

DDR? DDR? STATUS

Clears the Device

Dependent Register

(DDR).

DEF DEFINE? FUNCTION Specifies math expression

for function evaluation.

DELF DELETE_FILE MASS STORAGE Deletes files from mass

storage.

DIR DIRECTORY MASS STORAGE Creates and deletes file

directories.

DTJN DOT_JOIN DISPLAY Controls the interpolation

lines between data points.

*ESE *ESE STATUS

Sets the Standard Event

Status Enable register

(ESE).

*ESR? *ESR? STATUS Reads, clears the Event

Status Register (ESR).

EXR? EXR? STATUS

Reads, clears the

Execution error Register

(EXR).

FLNM FILENAME MASS STORAGE Changes default

filenames.

FRTR FORCE_TRIGGER ACQUISITION Forces the instrument to

make one acquisition.

SDS1000 Series

SDS-RCM 7

FVDISK FORMAT_VDISK MASS STORAGE Reads the capability of the

USB device.

FILT FILTER FUNCTION Enables or disables the

filter of specified source.

FILTS FILT_SET FUNCTION

Selects the type of filter,

and sets the limit value of

filter.

FFTW FFT_WINDOW FUNCTION Selects the window of

FFT.

FFTZ FFT_ZOOM FUNCTION Selects the zoom in/out

times of FFT trace.

FFTS FFT_SCALE FUNCTION Selects the vertical scale

of FFT trace.

FFTF FFT_FULLSCREEN FUNCTION

Enables or disables to

display the FFT trace full

screen.

GRDS GRID_DISPLAY DISPLAY Selects the type of grid

GCSV GET_CSV WAVEFORMTRANS Specifies waveform data

of format to controller.

HMAG HOR_MAGNIFY DISPLAY Horizontally expands the

selected expansion trace.

HPOS HOR_POSITION DISPLAY Horizontally positions

intensified zone’s center.

HCSU HARDCOPY_SETUP HARD COPY Configures the hard-copy

driver.

*IDN? *IDN? MISCELLANEOUS For identification

purposes.

INTS INTENSITY DISPLAY Sets the grid or trace/text

intensity level.

ILVD INTERLEAVED ACQUISITION

Enables/disables random

interleaved sampling

(RIS).

INR? INR? STATUS

Reads, clears INternal

state change Register

(INR).

INVS INVERT_SET DISPLAY

Invert the trace or the

math waveform of

specified source.

LOCK LOCK MISCELLANEOUS Lock keyboard

MENU MENU DISPLAY Enables or disables to

display the current menu.

MTVP MATH_VERT_POS ACQUISITION

Controls the vertical

position of math

waveform of specified

source.

SDS1000 Series

8 SDS-RCM

MTVD MATH_VERT_DIV ACQUISITION

Controls the vertical

sensitivity of math

waveform of specified

source.

MEAD MEASURE_DELY FUNCTION Selects the type of delay

measure.

OFST OFFSET ACQUISITION Allows output channel

vertical offset adjustment.

*OPC *OPC STATUS

Sets the OPC bit in the

Event Status Register

(ESR).

*OPT? *OPT? MISCELLANEOUS Identifies oscilloscope

options.

PACL PARAMETER_CLR CURSOR

Clears all current

parameters in Custom,

Pass/Fail.

PACU PARAMETER_CUSTO

M CURSOR Controls parameters with

customizable qualifiers.

PAVA? PARAMETER_VALU

E? CURSOR Returns current parameter,

mask test values.

PDET PEAK_DETECT ACQUISITION Switches the peak detector

ON and OFF.

PERS PERSIST DISPLAY Enables or disables the

persistence display mode.

PESU PERSIST_SETUP DISPLAY Selects display persistence

duration.

PNSU PANEL_SETUP SAVE/RECALL Complements the

*SAV/*RST commands.

PFDS PF_DISPLAY FUNCTION

Enables or disables to

display the test and the

message options of

pass/fail.

PFST PF_SET FUNCTION Sets the X mask and the Y

mask.

PFSL PF_SAVELOAD SAVE/RECALL Saves or recalls the

created mask setting.

PFCT PF_CONTROL FUNCTION

Selects the “operate”,

“output” and the “stop on

output” which are the

options of pass/fail.

PFCM PF_CREATEM FUNCTION Creates the mask of the

pass/fail.

PFDD PF_DATEDIS FUNCTION

Return the number of the

pass/fail monitor which

can be displayed on the

screen.

SDS1000 Series

SDS-RCM 9

*RCL *RCL SAVE/RECALL Recalls one of five non-

volatile panel setups.

REC RECALL WAVEFORMTRANS

Recalls a file from mass

storage to internal

memory.

RCPN RECALL_PANEL SAVE/RECALL Recalls a front-panel setup

from mass storage.

*RST *RST SAVE/RECALL The *RST command

initiates a device reset.

REFS REF_SET FUNCTION Sets the reference

waveform and its options.

*SAV *SAV SAVE/RECALL Stores current state in non-

volatile internal memory.

SCDP SCREEN_DUMP HARD COPY Causes a screen dump to

controller.

SCSV SCREEN_SAVE DISPLAY Controls the automatic

screen saver.

*SRE *SRE STATUS Sets the Service Request

Enable register (SRE).

*STB? *STB? STATUS Reads the contents of

IEEE 488.

STOP STOP ACQUISITION Immediately stops signal

acquisition.

STO STORE WAVEFORMTRANS Stores a trace in internal

memory or mass storage.

STPN STORE_PANEL SAVE/RECALL Stores front-panel setup to

mass storage.

STST STORE_SETUP WAVEFORMTRANS Controls the way in which

traces are stored.

SAST SAMPLE_STATUS ACQUISITION Return the acquisition

status of the scope

SARA SAMPLE_RATE ACQUISITION Return the sample rate of

the scope

SANU SAMPLE_NUM ACQUISITION

Return the number of

sampled points available

from last acquisition and

the trigger position

SKEW SKEW ACQUISITION Sets the skew of specified

trace.

SET50 SETTO%50 FUNCTION

Sets the trigger level of the

trigger source to the centre

of the signal amplitude.

SXSA SINXX_SAMPLE ACQUISITION Sets the type of the

interpolation.

TDIV TIME_DIV ACQUISITION Modifies the time base

setting.

SDS1000 Series

10 SDS-RCM

TMPL TEMPLATE WAVEFORM

TRANSFER

Produces a complete

waveform template copy.

TRA TRACE DISPLAY Enables or disables the

display of a trace.

*TRG *TRG ACQUISITION Executes an ARM

command.

TRCP TRIG_COUPLING ACQUISITION

Sets the coupling mode of

the specified trigger

source.

TRDL TRIG_DELAY ACQUISITION Sets the time at which the

trigger is to occur.

TRLV TRIG_LEVEL ACQUISITION

Adjusts the trigger level of

the specified trigger

source.

TRMD TRIG_MODE ACQUISITION the trigger mode.

TRSE TRIG_SELECT ACQUISITION Selects the condition that

will trigger acquisition.

TRSL TRIG_SLOPE ACQUISITION

Sets the trigger slope of

the specified trigger

source.

UNIT UNIT ACQUISITION Sets the unit of specified

trace.

VPOS VERT_POSITION DISPLAY Adjusts the vertical

position of the FFT trace.

VDIV VOLT_DIV ACQUISITION Sets the vertical

sensitivity.

VTCL VERTICAL ACQUISITION

Controls the vertical

position of the slope

trigger line.

WF WAVEFORM WAVEFORMTRANS Gets the waveform from

the instrument.

WFSU WAVEFORM_SETUP WAVEFORMTRANS

Specifies amount of

waveform data to go to

controller.

WAIT WAIT ACQUISITION

Prevents new analysis

until current has been

completed.

XYDS XY_DISPLAY DISPLAY Enables or disables to

display the XY format

Tabla de contenidos

Otros manuales de Equipo de prueba de SIGLENT

SIGLENT

SIGLENT SDL1000X Manual de usuario

SIGLENT

SIGLENT SDS1204X HD Manual de usuario

SIGLENT

SIGLENT SDS-2000X-LA Manual de usuario

SIGLENT

SIGLENT SDL1000X Manual de usuario

SIGLENT

SIGLENT SDS2104X Manual de usuario

SIGLENT

SIGLENT SDS1000X-E Series Manual de usuario

SIGLENT

SIGLENT SDS1000X-E Series Manual de usuario

SIGLENT

SIGLENT SDS2000X Plus Series Manual de usuario

SIGLENT

SIGLENT SDS2000X-E Series Manual de usuario

SIGLENT

SIGLENT SDS1000X Series Manual de usuario

SIGLENT

SIGLENT SDS1000CFL Series Manual de usuario

SIGLENT

SIGLENT SDL1000X Manual de usuario

SIGLENT

SIGLENT SDS1000CFL Series Manual de usuario

SIGLENT

SIGLENT SDS6000L Series Manual de usuario

SIGLENT

SIGLENT SDS1000CML+ Manual de usuario

SIGLENT

SIGLENT SDS1004X-E Series Manual de usuario

SIGLENT

SIGLENT SDS5000X Series Manual de usuario

SIGLENT

SIGLENT SDS5000X Series Manual de usuario

SIGLENT

SIGLENT SDS7000A Series Manual de usuario

SIGLENT

SIGLENT SDS1000CML series Manual de usuario

SIGLENT

SIGLENT SDS2000X Series Manual de usuario

SIGLENT

SIGLENT SAP5000D Manual de usuario

SIGLENT

SIGLENT SDS2000X Plus Series Manual de usuario

SIGLENT

SIGLENT SDS2000X Series Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario