Siemens FP2011-U1 Manual de usuario
Installation Instructions
Model FP2011-U1
6.5 Amp Power Supply Module
P/N 315-050222-2
Siemens Industry, Inc.
Building Technologies Division
Florham Park, NJ
Siemens Canada, Ltd.
1577 North Service Road East
Oakville, Ontario
L6H 0H6 Canada
INTRODUCTION
The Model FP2011-U1 is a modular power supply that
provides primary regulated 26VDC power for normal
operation. The FP2011-U1 is rated at 6.5A and is filtered
and regulated. Regulation is +/- 0.25V under all load/
line cases.
The module incorporates a 4.0A non-resettable slow-
blow fuse on the primary input and includes a built-in
AC line filter for surge and noise suppression. The
FP2011-U1 mounts in a standard enclosure.
There are no serviceable parts to be maintained.
INSTALLATION
Remove all system power before installa-
tion, first battery then AC. (To power up,
connect the AC first, then the battery.)
The installation kit for the FP2011-U1 includes the
following:
One FP2011-U1 module
Four #10 lock nuts
One 4-wire cable
For 240VAC installation, reference the
Jumper Removal section on page 2
before installing the FP2011-U1 module.
Mounting
Mount the enclosure to the wall before mounting the
FP2011-U1 power supply to the enclosure.
1. Make sure that the dedicated circuit breaker for
the FP2011-U1 is turned off at the mains.
2. Place the FP2011-U1 housing over the four studs
provided in the enclosure indicated in the system
installation manual. (Refer to Figure 1 for a typical
example.)
3. Using the lock nuts provided, secure the FP2011-
U1 to the mounting studs of the enclosure.
FP2011-U1
Typical Enclosure
FP2011-U1 Mounting
Studs (4 places)
Figure 1
FP2011-U1 Mounting in Typical Enclosure
Wiring
The FP2011-U1 is designed to operate from a 120 or
240 VAC, 50/60 Hz power source. Use a separate or
dedicated circuit breaker. Wire in accordance with the
authority having jurisdiction and Article 760 of the NEC
NFPA 70 latest edition.
Run the earth ground from a suitable source to the
FP2011-U1. Check local requirements. Conduit is not
an acceptable earth ground conductor.
1. Connect the AC mains to the 3-position terminal
block on the FP2011-U1 as shown in Figure 2.
Black (L - Live)
White (N - Neutral)
Green (G - Earth Ground)
2
2. Connect the 4-wire cable included in the installation
kit to the 4-position header on the FP2011-U1. The
cable is keyed and will connect in only one way.
Connect the other end of the cable to the terminal
block (TB) indicated in the system installation
manual. This cable is also keyed and will connect
in only one way. (Refer to Figure 3.)
FP2011-U1
Black (L)
White (N)
Green (G)
LNG
AVANT ENTRETIEN
DESACTIVEZ L'UNITE
REMOVING
TERMINAL
BLOCK PROTECTION
DISCONNECT POWER
PRIOR TO
WARNING
AC
Mains
SUPERVISED
NON-POWER
LIMITED
18 AWG MIN.
4-POSITION
HEADER
Figure 2
Wiring the FP2011-U1
MATES WITH
FP2011-U1
POWER SUPLY
MATES WITH CONNECTOR
ON PCB BOARD
Blue
Black
Black
Red
FERRITE
CORE
Figure 3
FP2011-U1 Power Supply Cable
ELECTRICAL RATINGS
Primary Power:
Input: 120VAC or 240VAC,
50/60Hz @ 2.0A Max.
Output: 26VDC @ 6.5A Max.
Max Current: 6.5A (2 Hours Max.)
Filtered and Regulated
JUMPER REMOVAL FOR 240VAC ONLY
Remove all system power before installa-
tion, first battery then AC. (To power up,
connect the AC first, then the battery.)
If the AC input is 240VAC, you will need to remove
the cover of the FP2011-U1 housing and remove the
jumper on J1. Follow the steps listed below.
1. On the side of the housing with 5 screws, remove
all 5 screws and place them to one side.
2. On the side of the housing with 8 screws, remove
the 5 screws indicated in Figure 4 and place them to
one side.
DO NOT REMOVE THE REMAINING 3 SCREWS.
Figure 4
Removing 5 Screws from the Side of the
FP2011-U1 that has 8 Screws
3. Take off the top cover.
4. Locate jumper J1. Refer to Figure 5 to find the
location.
FP2011-U1 PCB
For 240VAC, Remove Jumper
Figure 5
Location of Jumper J1 for 120VAC on the FP2011-U1
Power Supply (For 240VAC, Remove Jumper)
5. Remove J1 by hand or by using a tool.
6. Replace the top cover on the FP2011-U1 and
secure in place by installing the 10 screws that
were removed.
P/N 315-050222-2
3
P/N 315-050222-2
Cyber security disclaimer
Siemens products and solutions provide security functions to ensure the secure operation of building
comfort, fire safety, security management and physical security systems. The security functions on
these products and solutions are important components of a comprehensive security concept.
It is, however, necessary to implement and maintain a comprehensive, state-of-the-art security concept
that is customized to individual security needs. Such a security concept may result in additional site-
specific preventive action to ensure that the building comfort, fire safety, security management or
physical security system for your site are operated in a secure manner. These measures may include,
but are not limited to, separating networks, physically protecting system components, user awareness
programs, defense in depth, etc.
For additional information on building technology security and our offerings, contact your Siemens
sales or project department. We strongly recommend customers to follow our security advisories,
which provide information on the latest security threats, patches and other mitigation measures.
http://www.siemens.com/cert/en/cert-security-advisories.htm
P/N 315-050222-2 Document ID A6V10333499
THIS PAGE HAS BEEN LEFT INTENTIONALLY BLANK.
Tabla de contenidos
Otros manuales de Fuente de alimentación de Siemens
Siemens
Siemens COMPS Manual de usuario
Siemens
Siemens SINAMICS S120 Manual de usuario
Siemens
Siemens SITOP PSU8600 Manual de usuario
Siemens
Siemens SITOP UPS1600 Documento técnico
Siemens
Siemens SITOP Power 4 6EP1332-2BA00 Manual de usuario
Siemens
Siemens SITOP power 20 Manual de usuario
Siemens
Siemens SIMATIC NET PS598-1 Guía del administrador
Siemens
Siemens SITOP series Manual de usuario
Siemens
Siemens PSC-12 Manual de usuario
Siemens
Siemens SIMATIC PS307 Manual de usuario
Siemens
Siemens SITOP Power 20 6EP1 536-2AA00 Manual de usuario
Siemens
Siemens SIDOOR ATD400S Manual de usuario
Siemens
Siemens SITOP power flexi Manual de usuario
Siemens
Siemens PSR-1 Manual de usuario
Siemens
Siemens 7XV5810-0.A00 Manual de usuario
Siemens
Siemens SITOP PSU100S Manual de usuario
Siemens
Siemens SITOP series Manual de usuario
Siemens
Siemens SINAMICS G120P PM330 Instrucciones de funcionamiento y mantenimiento
Siemens
Siemens SITOP C98130-A1251-A1-02-19 Manual de usuario
Siemens
Siemens 7XV5810-0BA00 Manual de usuario
