Siemens SC9000 Manual de usuario

DU-DR-0016-SC9000 Rev A 6/4/02 GCX Corp. Page 1 of 4

GCX Mounting Assembly Operation/Installation Manual

Dräger Model Cato ® with Siemens SC9000 Patient Monitor

Patient Monitor – Left Side on Pivot Arm / Power Supply on Right Side

The purpose of these instructions is to:

1. Describe attachment of GCX mounting hardware to the Cato anesthesia machine.

2. Describe attachment of the Siemens monitor to the GCX mounting hardware.

WARNING: USE OF MOUNTING HARDWARE AND MONITORING COMPONENTS OTHER THAN THOSE

DESCRIBED IN THIS DOCUMENT MAY RESULT IN SERIOUS INJURY DUE TO TIPPING OF THE

ANESTHESIA MACHINE.

THIS CATO MOUNTING CONFIGURATION REQUIRES THE 40KG COUNTERWEIGHT WITH

EXTENDED WHEEL ADAPTER UPGRADE SET FROM DRÄGER (PART NUMBER: 86 018 68)

Installer: When installation is completed, provide these instructions to the end user for future reference.

INSTALLATION

Tools Required: Philips head screw driver, Hex key (incl.).

Mounting the Channel to Cato Edition

Parts Required: 4" Channel, M6 x 16 mm FHMS screws (2).

Brass Plate with inserts from Dräger (M29110)

1. To attach the Channel to the Cato left side accessory track,

locate the brass plate in the accessory track, align the

mounting holes in the Channel with the threaded holes on

the brass plate then run the M5 flat head screws (2) partly

in. (Note: Fixed Stop is at the bottom of the Channel)

2. Set the height of the Channel in the accessory track and

tighten the M6 screws to hold in place.

Prepare M Series Arm

1) Install the Tilt Limiting Stop screw.

M6 x 16 mm (2) FHMS

Accessor

Track

Fixed Sto

5/16-18 x ½” SHCS (1)

DU-DR-0016-SC9000 Rev A 6/4/02 GCX Corp. Page 2 of 4

Install M Series Arm

1. The Slide has (2) ¼-20 x ¾” SHSS set screws that, when tightened, secure the Arm at the desired location

within the Channel.

2. While supporting the bottom of the Arm with one hand, guide the Slide (at the rear of the arm) into the top

of the Channel.

3. Once the Arm is at the desired height, tighten both set screws using the supplied 1/8” (3 mm) hex key.

Slide Pick & Go Base into Mounting Plate

1) Align the mounting adapter located at the bottom of the Pick & Go base with the edge of Mounting Plate. Slide the

Pick & Go base into the plate until it stops at the Spring Plunger (located below the Mounting Plate).

Pull the Spring Plunger and continue to slide the base until the mounting adapter engages the Spring Plunger. Tighten

the (4) nylon thumb screws on the back of the Mounting Plate.

Install 4” Cato Channel on Right Side

As described on Page 1 of this document.

Install Power Supply Mounting Adapter to Siemens Power Supply Mount (Siemens P/N: 4720129)

1) Install according to the instructions included with the adapter.

Slide Power Supply Mount into Channel & Insert Power Supply

1) Align the Slide of the mount with edge of the Channel insert into channel.

DU-DR-0016-SC9000 Rev A 6/4/02 GCX Corp. Page 3 of 4

INSTRUCTIONS FOR USE – M Series Pivot Arm

Pivot

1. To pivot the Arm (near the wall), simply push on the side of the Arm or mounted device.

2. To adjust the pivot tension at the Slide, use a ½” (or 13mm) socket driver to tighten or loosen the Pivot

Tension Bolt to obtain the desired tension.

Swivel

1) To rotate the device simply push or pull the corners of the device.

2) To adjust the swivel tension, use a ½” (or 13mm) socket driver to tighten or loosen the Swivel Tension Adjustment Bolt

located under the front end of the Arm.

Tilt

1. Grasp the top and bottom of the device and tilt it to the desired angle.

2. To adjust the overall tilt tension, evenly tighten or loosen the (2) #10-32 x 5/8” SHCS Tilt Tension Adjustment Screws

using the supplied 5/32 (4 mm) hex key.

Cable Management

1. An open cavity beneath the arm with flexible cable covers manage cables going to and from the front and rear of the

arm.

Flexible Cable Covers

Pivot Tension Bolt

Swivel Tension Bolt

Pivot Arm

DU-DR-0016-SC9000 Rev A 6/4/02 GCX Corp. Page 4 of 4

Cleaning

1. The mounting assembly may be cleaned with most mild, non-abrasive solutions commonly used in the hospital

environment (e.g. diluted bleach, ammonia, or alcohol solutions).

2. The surface finish will be permanently damaged by strong chemicals and solvents such as acetone and

trichloroethylene.

3. Steel wool or other abrasive material should never be used.

4. Damage caused by the use of unapproved substances or processes will not be warranted. To verify compatibility,

It is recommended that any cleaning solution be tested on a small area of the arm that is not visible.

5. Never submerge the mounting arm. Wipe any cleaning agents off of the arm immediately, using a water-dampened

cloth. Dry the arm thoroughly after cleaning.

CAUTION: GCX makes no claims regarding the efficacy of the listed chemicals or processes as a means for controlling

infection. Consult your hospital’s infection control officer or epidemiologist. To clean or sterilize mounted devices or

accessory equipment, refer to the specific instructions supplied with those products.

PARTS LIST

GCX P/N Dräger P/N DESCRIPTION

WMM-0002-02

DR-0017-82

MM15278

MM15719

M29110

12” M Series Pivot Arm

4” Cato Channel (2)

Accessory Track Brass Plate (Dräger)

Power Supply Right Side (CPS)

GCX P/N Siemens P/N Dräger P/N DESCRIPTION

-- 4720129 -- Siemens Power Supply Holster

SI-0041-06 -- MM15754 Siemens Power Supply Flush Mount for

Siemens P/N 4720129

DR-0017-82 -- MM15719 4" Channel /w T-Nuts

-- -- M29110 Accessory Track Brass Plate (Dräger)

Otros manuales de Monitor de Siemens

Siemens

Siemens SCD 1515-E Manual de usuario

Siemens

Siemens CMTC1913 Manual de usuario

Siemens

Siemens 43B1-M Manual de usuario

Siemens

Siemens SCD 1997-E Manual de usuario

Siemens

Siemens SCD 1297 Series Manual de usuario

Siemens

Siemens MCM-21T2 Manual de usuario

Siemens

Siemens CMCC1020 Manual de usuario

Siemens

Siemens SITRANS RD200 Manual de usuario

Siemens

Siemens SIREMOBIL Compact L Manual de usuario

Siemens

Siemens SIMATIC IPC477E 1900 PRO HD LR Ext. Manual de usuario

Siemens

Siemens MCM 17P1 Manual de usuario

Siemens

Siemens 30 64 581 B5310 Instrucciones de funcionamiento y mantenimiento

Siemens

Siemens 19T2 Manual de usuario

Siemens

Siemens SCD 1898-I Manual de usuario

Siemens

Siemens SITRANS RD100 Manual de usuario

Siemens

Siemens AZL66 Series Manual de usuario

Siemens

Siemens FUJITSU S383FA-V151 Manual de usuario

Siemens

Siemens SIMATIC S7 Manual de usuario

Siemens

Siemens SIMOMED HM Instrucciones de funcionamiento

Siemens

Siemens 3TK2810-1 Manual de usuario

Siemens

Siemens AEP Manual de usuario

Siemens

Siemens UP587/1 Series Manual de servicio

Siemens

Siemens MCM 1902 Manual de usuario

Siemens

Siemens 175V Manual de usuario

Manuales populares de Monitor de otras marcas

Linear Acoustic

Linear Acoustic LQ-1000 Manual de usuario

AOC

AOC I2579V Manual de usuario

Gateway

Gateway FPD1520 Manual de usuario

Furuno

Furuno Mu 120c Manual de usuario

Asus

Asus VB171D - 17" LCD Monitor Manual de usuario

Dell

Dell S2230MX Instrucciones de uso

Philips

Philips 107C64 Manual de usuario

Dell

Dell S2409WFP Manual de usuario

EverFocus

EverFocus EN-7517E Manual de usuario

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manual de usuario

Dell

Dell Precision 7680 Manual de instrucciones

LG 50PM1M - - 50" Plasma Panel Manual de usuario

Bosch

Bosch DDU 9 Manual de usuario

Acer

Acer A231HL Manual de usuario

Philips

Philips 86BDL4152T Manual de usuario

NEC

NEC AccuSync LCD5V Manual de usuario

Emay

Emay SleepO2 Manual de usuario

IBM

IBM 6360 Instrucciones de instalación