Siemens SIMATIC S7-1500R/H Documento técnico
EQUIPMENT MANUAL
CPU 1518HF-4 PN
Edition
S7-1500R/H
support.industry.siemens.com
6ES7518-4JP00-0AB0
11/2022
SIMATIC
Siemens AG
Digital Industries
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E49868646-AB
Ⓟ 10/2022 Subject to change
Copyright © SiemensAG 2021 - 2022.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of SiemensAG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
4
1 Introduction........................................................................................................................................ 5
1.1 S7-1500R/H Documentation Guide.................................................................................... 6
1.1.1 Information classes S7-1500R/H........................................................................................ 6
1.1.2 SIMATIC Technical Documentation.................................................................................... 7
2 Safety instructions.............................................................................................................................. 9
2.1 Security information......................................................................................................... 9
3 Product overview................................................................................................................................ 10
3.1 New functions.................................................................................................................. 10
3.2 Configuration and operating principle............................................................................... 11
3.3 Hardware properties......................................................................................................... 13
3.4 Firmware functions........................................................................................................... 16
3.5 Operator controls and display elements............................................................................. 18
3.5.1 Front view of the CPU with closed front flap...................................................................... 18
3.5.2 Front view of the CPU without front flaps.......................................................................... 20
3.5.3 Rear view of the CPU......................................................................................................... 21
3.5.4 Bottom view..................................................................................................................... 22
3.6 Mode selector................................................................................................................... 22
4 Connecting......................................................................................................................................... 24
4.1 Terminal assignment........................................................................................................ 24
5 Alarm, error and system messages.................................................................................................... 29
5.1 Status and error display of the CPU.................................................................................... 29
6 Technical specifications...................................................................................................................... 34
A Dimension drawing............................................................................................................................ 44
CPU 1518HF-4 PN (6ES7518-4JP00-0AB0)
Equipment Manual, 11/2022, A5E49868646-AB
Table of contents
Introduction 1
Purpose of the documentation
This manual supplements the system manual of the S7-1500R/H redundant system and the
function manuals. This manual contains a description of the module-specific information. The
system-related functions are described in the system manual. All system-spanning functions
are described in the function manuals.
The information provided in this manual and the system manual enables you to commission
the CPU1518HF-4PN.
NOTE
When using CPU 1518HF-4 PN in Safety mode, note the description of the fail-safe system
SIMATIC Safety SIMATIC Safety - Configuring and Programming
(https://support.industry.siemens.com/cs/ww/en/view/54110126) programming and
operating manual.
Conventions
STEP7: In this documentation, "STEP7" is used as a synonym for all versions of the
configuration and programming software "STEP7 (TIA Portal)".
Please also observe notes marked as follows:
NOTE
A note contains important information on the product described in the documentation, on
the handling of the product or on the section of the documentation to which particular
attention should be paid.
Recycling and disposal
For environmentally friendly recycling and disposal of your old equipment, contact a certified
electronic waste disposal company and dispose of the equipment according to the applicable
regulations in your country.
Industry Mall
The Industry Mall is the catalog and order system of Siemens AG for automation and drive
solutions on the basis of Totally Integrated Automation (TIA) and Totally Integrated Power
(TIP).
You can find catalogs for all automation and drive products on theInternet
(https://mall.industry.siemens.com).
5
CPU 1518HF-4 PN (6ES7518-4JP00-0AB0)
Equipment Manual, 11/2022, A5E49868646-AB
1.1 S7-1500R/H Documentation Guide
1.1.1 Information classes S7-1500R/H
The documentation for the redundant S7-1500R/H system is arranged into three areas.
This arrangement enables you to access the specific content you require.
You can download the documentation free of charge from the Internet
(https://support.industry.siemens.com/cs/ww/en/view/109742691).
Basic information
The System Manual and Getting Started describe in detail the configuration, installation,
wiring and commissioning of the redundant S7-1500R/H system.
The STEP7 online help supports you in the configuration and programming.
Examples:
•Getting Started S7-1500R/H
•System manual S7-1500R/H
•Online help TIA Portal
Device information
Equipment manuals contain a compact description of the module-specific information, such
as properties, wiring diagrams, characteristics and technical specifications.
Examples:
•Equipment Manuals CPUs
•Equipment Manuals Power Supply Modules
General information
The function manuals contain detailed descriptions on general topics relating to the
redundant S7-1500R/H system.
Examples:
•Function Manual Diagnostics
•Function Manual Communication
•Function manual Structure and Use of the CPU Memory
•Function Manual Cycle and Response Times
•PROFINET Function Manual
Product Information
Changes and supplements to the manuals are documented in a Product Information. The
Product Information takes precedence over the device and system manuals.
You can find the latest Product Information on the redundant S7-1500R/H system on the
Internet. (https://support.industry.siemens.com/cs/ww/en/view/109742691)
6CPU 1518HF-4 PN (6ES7518-4JP00-0AB0)
Equipment Manual, 11/2022, A5E49868646-AB
Introduction
1.1 S7-1500R/H Documentation Guide
Manual Collection S7-1500/ET200MP
The Manual Collection S7-1500/ET200MP contains the complete documentation on the
redundant S7-1500R/H system gathered together in one file.
You can find the Manual Collection on the Internet.
(https://support.industry.siemens.com/cs/ww/en/view/86140384)
SIMATICS7-1500 comparison list for programming languages
The comparison list contains an overview of which instructions and functions you can use for
which controller families.
You can find the comparison list on the Internet.
(https://support.industry.siemens.com/cs/ww/en/view/86630375)
1.1.2 SIMATIC Technical Documentation
Additional SIMATIC documents will complete your information. You can find these
documents and their use at the following links and QR codes.
The Industry Online Support gives you the option to get information on all topics. Application
examples support you in solving your automation tasks.
Overview of the SIMATIC Technical Documentation
Here you will find an overview of the SIMATIC documentation available in Siemens Industry
Online Support:
Industry Online Support International
(https://support.industry.siemens.com/cs/ww/en/view/109742705)
Watch this short video to find out where you can find the overview directly in Siemens
Industry Online Support and how to use Siemens Industry Online Support on your mobile
device:
Quick introduction to the technical documentation of automation products per
video (https://support.industry.siemens.com/cs/us/en/view/109780491)
YouTube video: Siemens Automation Products - Technical Documentation at a
Glance (https://youtu.be/TwLSxxRQQsA)
mySupport
With "mySupport" you can get the most out of your Industry Online Support.
Registration You must register once to use the full functionality of "mySupport". After registra
tion, you can create filters, favorites and tabs in your personal workspace.
7
Introduction
1.1 S7-1500R/H Documentation Guide
CPU 1518HF-4 PN (6ES7518-4JP00-0AB0)
Equipment Manual, 11/2022, A5E49868646-AB
Support requests Your data is already filled out in support requests, and you can get an overview of
your current requests at any time.
Documentation In the Documentation area you can build your personal library.
Favorites You can use the "Add to mySupport favorites" to flag especially interesting or fre
quently needed content. Under "Favorites", you will find a list of your flagged
entries.
Recently viewed
articles
The most recently viewed pages in mySupport are available under "Recently viewed
articles".
CAx data The CAx data area gives you access to the latest product data for your CAx or CAe
system. You configure your own download package with a few clicks:
• Product images, 2D dimension drawings, 3D models, internal circuit diagrams,
EPLAN macro files
• Manuals, characteristics, operating manuals, certificates
• Product master data
You can find "mySupport" on the Internet. (https://support.industry.siemens.com/My/ww/en)
Application examples
The application examples support you with various tools and examples for solving your
automation tasks. Solutions are shown in interplay with multiple components in the system -
separated from the focus on individual products.
You can find the application examples on the Internet.
(https://support.industry.siemens.com/cs/ww/en/ps/ae)
8CPU 1518HF-4 PN (6ES7518-4JP00-0AB0)
Equipment Manual, 11/2022, A5E49868646-AB
Introduction
1.1 S7-1500R/H Documentation Guide
Safety instructions 2
2.1 Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. Such systems, machines and components should only be connected
to an enterprise network or the internet if and to the extent such a connection is necessary
and only when appropriate security measures (e.g. firewalls and/or network segmentation)
are in place.
For additional information on industrial security measures that may be implemented, please
visit (https://www.siemens.com/industrialsecurity).
Siemens' products and solutions undergo continuous development to make them more
secure. Siemens strongly recommends that product updates are applied as soon as they are
available and that the latest product versions are used. Use of product versions that are no
longer supported, and failure to apply the latest updates may increase customers' exposure to
cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed visit (https://www.siemens.com/cert).
9
CPU 1518HF-4 PN (6ES7518-4JP00-0AB0)
Equipment Manual, 11/2022, A5E49868646-AB
CPU 1518HF-4 PN (6ES7518-4JP00-0AB0)
Equipment Manual, 11/2022, A5E49868646-AB
10
Product overview 3
3.1 New functions
This section contains an overview of the most important new firmware functions of the CPU
since the last edition of the manual.
New functions of the CPU in firmware version V3.0
New functions Customer benefits Where can I find information?
Support
PROFINET system redundancy R1
As of FW version V3.0, the S7-1500H redundant
system supports PROFINET system redundancy
R1:
• ET 200SP IM 155-6 PN R1
(6ES7155-6AU00-0HM0)
• ET 200SP HA IM 155-6 PN HA
(6DL1155-6AU00-0PM0)
• ET 200iSP IM 152-1 PN
(6ES7152-1BA00-0AB0)
R1 devices are equipped with two interface mod
ules compared to S2 devices. If one interface
module fails, the R1 device can still be reached
by the H-CPUs via the second interface module.
Thus, R1 devices have a higher availability than
S2 devices.
• S7-1500R/H System Manual
(https://support.industry.
siemens.
com/cs/ww/en/view/109754
833)
• PROFINET Function Manual
(http://support.automation.
siemens.
com/WW/view/en/49948856)
New configuration variants for S7-1500H As of FW version V3.0, the S7-1500H redundant
system supports additional configuration vari
ants:
• Configuration of PROFINET rings with R1
devices
• Configuration of a line topology with S2
devices, switched S1 devices
• Configuration of a line topology with R1
devices
• Configuration of a combined topology with
R1 devices, S2 devices
• Configuration without additional devices
This allows you to connect the S7-1500H
redundant system to almost any network topo
logy and solve complex automation tasks.
S7-1500R/H System Manual
(https://support.industry.
siemens.
com/cs/ww/en/view/109754833)
OB 70 As of FW version V3.0, OB 70 (I/O redundancy
error) is available for the diagnostics of R1 and
S2 devices in S7-1500H systems.
S7-1500R/H System Manual
(https://support.industry.
siemens.
com/cs/ww/en/view/109754833)
Otros manuales para SIMATIC S7-1500R/H
5
Tabla de contenidos
Otros manuales de Equipos industriales de Siemens
Siemens
Siemens 8GK9930 - 0KK03 Manual de usuario
Siemens
Siemens SIRIUS 3RT105/145 A/N Series Manual de usuario
Siemens
Siemens SIPLUS HCS4200 PROFINET Guía del administrador
Siemens
Siemens 3VA9978-0BF2 Series Manual de usuario
Siemens
Siemens RUGGEDCOM WIN7249 Manual de usuario
Siemens
Siemens SIMATIC CloudConnect CC7 Series Manual de usuario
Siemens
Siemens SIRIUS 3RH24 Series Manual de usuario
Siemens
Siemens Simatic PROFIsafe Manual de usuario
Siemens
Siemens 3VA9137-0CK12 Manual de usuario
Siemens
Siemens SIPROCESS GA700 Manual de usuario
Siemens
Siemens SIMATIC MV550 S Manual de usuario
Siemens
Siemens 8WD43 Manual de usuario
Siemens
Siemens SIMATIC NET RUGGEDCOM RX1512 Documento técnico
Siemens
Siemens SIRIUS 3UG4513 Manual de usuario
Siemens
Siemens SIMATIC RTLS PCB OEM PULSE Manual de usuario
Siemens
Siemens SIMATIC RTLS4084T Manual de usuario
Siemens
Siemens SIMATIC RTLS4030G Manual de usuario
Siemens
Siemens 8US1903-3AB00 Manual de usuario
Siemens
Siemens SIRIUS 3RW30 Manual de usuario
Siemens
Siemens BD2-AK 2M2 Series Manual de usuario
