Siemens S6 Manual de usuario
Private Communication Systems
Mobile Phones
Service Manual
S6 Power GSM
( S6 Classic GSM)
V 1.2
V1.2 Page 1 of 18 PN MP ST
D. Schnoor
/98
Private Communication Systems
Mobile Phones
Table of Contents
V1.2 Page 2 of 18 PN MP ST
D. Schnoor
/98
Technical Data S6 (D) Power GSM
Length 159 mm
Width 55 mm
Thickness 16/22 mm
Volume 155 cm3
Weight 180 gm (incl. battery)
Performance: GSM class (2 Watt)
Frequency Range: Tx 890-915 MHz
Rx 935-960 MHz
Powersupply: Metal Hydride battery (3,6V/700mAh)
Standby time: up to 60 hours
Talk time: Up to hours.
Carging Time: Full charge in 75 minutes
Display LCD high-resolution graphic display, 97 x 33 pixels, rows
of 16 characters
SIM Card Type: Small (plug in) 3V or 5V
Private Communication Systems
Mobile Phones
General Infor ation
The S6 Power is a consumer handset technically based on E10. It is also available
as a dualrate version (S6 D Power).
Mechanical Concept
Note: All part numbers refer to mechanical drawing in section 4.1!
The S6 Power consists of two boards, the RF & Control module (1010) and the user
interface (1020).
The connection between those two boards is not made by a normal connector with
plug-in contacts, but by a special interconnector (1090) embedded into a shielding
frame (1060). This interconnector is upholding the connection through the pressure
implied on it by the housing.
Be careful when assembling the interconnector. Avoid any kind of dust or dirt
because it will affect the contacts of the interconnector.
The only removable part on the user interface is the ringer gasket (1080) which is
needed to increase the ringer volume.
Furthermore there is a RF-plug on the user interface which has to be plugged into
the appropriate connector on the RF & control module. This conection is very
essential because it is the RF signal from / to the internal antenna.
The shielding is done by the lower case shell (1050) which is covered with a
conductive material, so no additional shielding screen is necessary.
The antenna (1130) is directly screwed into the lower case shell.
V1.2 Page 3 of 18 PN MP ST
D. Schnoor
/98
Private Communication Systems
Mobile Phones
The keypad (1030), the loudspeaker (1120), the microphone (1110), the dust
protection frame (1075) and the display window (1070) are mounted into the upper
case shell (10 0). Make sure that the microphone contacts are properly bent up
when mounting.
When turning in the screws (11 0, 11 5 and 1150) make sure that the right torque is
used (25 Ncm), because this will have an effect on the contacts of the
interconnector.
V1.2 Page 4 of 18 PN MP ST
D. Schnoor
/98
Private Communication Systems
Mobile Phones
S6 Power mechanical drawing
Note: The nu bers shown above are NO ordering nu bers. Please use the nu bers
supplied by your service anager for ordering!
V1.2 Page 5 of 18 PN MP ST
D. Schnoor
/98
Private Communication Systems
Mobile Phones
Disassembling the S6 Power
1. Remove battery and SIM-Card.
2. Unscrew antenna (1130).
3. Unscrew 2 oval head screws (1160) (Torx 1,8x12).
. Turn out 2 short screws (11 0) (Torx 1,8x8).
5. Remove plastic disks (1170) and turn out the 3 long flat head screws
(1150)
(Torx 1,8x12).
6. Lift off the lower case shell (1050).
7. Lift composite of MMI-board (1020) and RF-and controle module (1010) out
of the upper case shell (10 0).
Only for level-2 repairs:
a) Remove ringer gasket (1080) from the MMI board (1020).
b) Remove RF plug from RF- and control module (1010).
c) Take off the MMI board (1020).
d) Take frame (1060) off the RF- and control module (1010).
e) Remove interconnector (1090) from the frame (1060).
8. If necessary: Take battery connector out of lower case shell (1050).
9. Take dust protection frame (1075) off the display glass frame (1070).
10. Take keypad (1030) out of upper case shell (10 0).
11. Remove earphone capsule (1120) and microphone (1110) from upper case
shell.
V1.2 Page 6 of 18 PN MP ST
D. Schnoor
/98
Private Communication Systems
Mobile Phones
Assembling the S6 Power
1. Put earphone capsule (1120) and microphone (1110) into upper case shell
(10 0).
2. Insert keypad (1030) into upper case shell (10 0).
3. Place dust protection frame (1075) on display glass frame (1070).
Attention: The smooth side has to face the MMI.
. If necessary: Insert battery connector into lower case shell (1050).
5. Insert composite of MMI-board (1020) and RF-and controle module (1010)
into upper case shell (10 0).
BEFORE (only for level 2 repairs):
a) Put interconnector (1090) to the frame (1060).
b) Position frame (1060) on the RF- and control module (1010).
c) Place MMI board (1020) on top of frame (1060).
d) Connect RF plug of MMI board (1020) to RF- and control
module (1010).
e) Mount ringer gasket (1080) on the MMI board (1020).
6. Close device with upper case shell (10 0). Make sure that the 6 hooks of
the upper case shell fit firmly into the respective slots of the lower
case shell (1050).
7. Screw 3 long flat head screws (1150) (Torx 1,8x12 /Torque 25 Ncm) into
lower case shell (1050). Close holes with plastic disks (1170)
afterwards.
8. Screw 2 short flat head screws (11 0) (Torx 1,8x8 /Torque 25 Ncm) into
lower case shell.
9. Screw 2 oval head screws (1160) (Torx 1,8x12 /Torque 25 Ncm) into lower
case shell.
10. Screw in Antenna (1130) (Torque 25 Ncm).
11. Insert SIM-Card and battery.
V1.2 Page 7 of 18 PN MP ST
D. Schnoor
/98
Private Communication Systems
Mobile Phones
Handset Datecodes
Siemens is using the industrial standard DIN EN 60062 to indicate the production /
service dates. The code is printed on the IMEI sticker located under the simcard
reader.
The first character of the datecode indicates the year of production:
F = 1995
H = 1996
J = 1997
K = 1998
The second character indicates the month of production:
1-9 = january to september
O = october
N = november
D = december
Example: K1 means that the set was produced in january of 1998.
V1.2 Page 8 of 18 PN MP ST
D. Schnoor
/98
-> YY = Datecode
Private Communication Systems
Mobile Phones
Hardware Concept
Block Diagram
V1.2 Page 9 of 18 PN MP ST
D. Schnoor
/98
Private Communication Systems
Mobile Phones
V1.2 Page 10 of 18 PN MP ST
D. Schnoor
/98
HiGOLD (PMB 2800)
Otros manuales para S6
1
Tabla de contenidos
Otros manuales de Teléfono móvil de Siemens
Siemens
Siemens CC75 Manual de usuario
Siemens
Siemens Gigaset M56 Manual de usuario
Siemens
Siemens CX75 Manual de usuario
Siemens
Siemens optiPoint WL1 professional Manual de usuario
Siemens
Siemens A75 Manual de usuario
Siemens
Siemens CX75 Manual de usuario
Siemens
Siemens MT50 Manual de usuario
Siemens
Siemens Gigaset 4010 Manual de usuario
Siemens
Siemens A71 Manual de usuario
Siemens
Siemens SL10 Manual de usuario
Siemens
Siemens A62 Manual de usuario
Siemens
Siemens MDACT Manual de usuario
Siemens
Siemens AX75 Manual de usuario
Siemens
Siemens SL45 Manual de usuario
Siemens
Siemens Gigaset S100 Manual de usuario
Siemens
Siemens Be inspired M55 Manual de usuario
Siemens
Siemens PEGASUS-DTC AX72 Manual de usuario
Siemens
Siemens S40 Manual de usuario
Siemens
Siemens C81 Manual de usuario
Siemens
Siemens M35 Manual de usuario
