Siemens SINUMERIK 808D Manual de usuario

No.:2012-12-001

I DT SNC M3S

808D set point cable X51～

～～

～X53 connecting with V60 driver instructions

1. 808D PPU interface X51～X53 is defined as axis pulse interface, the standard configuration is

SINAMCIS V60 drive.

( Taking a milling machine for an example)

2. The detail interface signal for Standard configuration SINAMCIS V60 drive as below:

808D PPU

X51~X53 port

symbol（colour）

The description of signal V60 port /pin

Remark

1 PULSE+ (green）

Positive pulse（NC output signal）

X5 / pin1 5V signal

9 PULSE- (yellow)

Negative pulse（NC output signal）

X5 / pin2 5V signal

2 DIR+ (gray)

DIRECTION +（NC output signal）

X5 / pin3 5V signal

10 DIR- (pink) DIRECTION -（NC output signal）

X5 / pin4 5V signal

3 ENA+ (brown)

Pulse enable+（NC output signal）

X5 / pin5 5V signal

11 ENA- (white) Pulse enable-（NC output signal）

X5 / pin6 5V signal

65 servo enable（NC output signal）

X6 / pin1

+24V=drive

enable

0V=drive disable

6 RST

(white/green) Alarm Reset（NC output signal）X6 / pin2 + 24V high active

7 M24 （red）

Servo enable and ALARM RESET

Ground X6 / pin3

5 ALM1

(red/blue)

Power from the pin 1 of X200,

+24V output X6 / pin4

15 ALM2 (blue) Alarm, from drive side（NC input

signal）X6 / pin5

When alarm is

triggered,ALM1,

ALM2 close

8 RDY1 (black) Power from the pin 1 of X200,

+24V output X6 / pin6

14 RDY2 (purple) Drive ready signal （NC input

signal）X6 / pin7

drive is ready, the

line close.

No.:2012-12-001

I DT SNC M3S

+24V

(white/yellow)

Power from the pin 1 of X200,

+24V output X6 / pin8

4 Z-M (gray/pink) Zero mark signal（NC input signal）

X6 / pin9 H = +24V; L = 0 V

M24

(brown/green)

Zero mark Ground X6 / pin10

Announcements

：

a) The + 24 V and M signals of X200 must be connected; otherwise, the communication

between the PPU and the drives does not function as it should.(reference 808D

electrical installation_201205 manual ,the 20 page and the 30 page)

b) If using Siemens standard cable to connect third party drive or using other cable,

please be sure good insulation for useless signal cable.

4.FAQ：

a) Q：axis disable，SINAMCIS V60 display alarm : “S-3”

Possible cause：

---The + 24 V and M signals of X200 is not be connected

---65 port of V60 not be connected

---please check the axis machine date : MD30130&MD30240&MD34200 set correctly

--- System has read disable effective signal

---65 enable M signal port and M signal port of X200 not connected the same ground

b) Q: 808D X51~X52 port was damaged

Possible cause：

--- Hot-plug the connector

--- Wrong wiring, Short circuits, cable breakage

Otros manuales para SINUMERIK 808D

Otros manuales de Cables y conectores de Siemens

Siemens

Siemens TC3A-107 Manual de instrucciones

Siemens

Siemens 3RK1911-2B 0 Series Manual de usuario

Siemens

Siemens 3VA957-0JB23 Series Manual de usuario

Siemens

Siemens 6FX2003-0DE01 Manual de usuario

Siemens

Siemens 3VT9500-4PL00 Manual de usuario

Siemens

Siemens SIMATIC BusAdapter Manual de usuario

Siemens

Siemens 3VA9373-0JJ24 Manual de usuario

Siemens

Siemens SENTRON VL160X Manual de usuario

Siemens

Siemens 3RT1916-4BB31 Manual de usuario

Siemens

Siemens PROFIBUS Documento técnico

Siemens

Siemens 3VM1340-1AA 2 Series Manual de usuario

Siemens

Siemens 3MT8040 Series Manual de usuario

Siemens

Siemens FastConnect FC SC Manual de usuario

Siemens

Siemens SIVACON 8PS BD01 Manual de usuario

Siemens

Siemens SENTRON 3NJ622 Manual de usuario

Siemens

Siemens SIMATIC NET IE FC RJ45 Plug 4x2 CAT 6A Guía del administrador

Siemens

Siemens SIPLUS CMS4000 IFN VIB-A Manual de usuario

Siemens

Siemens SIMATIC NET FC FO LC GK1900-1RB00-2AB0 Manual de usuario

Siemens

Siemens 7XV5450-0BA00/DD Manual de usuario

Siemens

Siemens 3VA9977-0KP80 Manual de usuario

Siemens

Siemens 3VA91 0J.1 Series Manual de usuario

Siemens

Siemens TSP-XC Manual de usuario

Siemens

Siemens MMI Manual de usuario

Siemens

Siemens 3TA1EG10 Manual de usuario

Manuales populares de Cables y conectores de otras marcas

Philips

Philips SWA6310 Manual de usuario

StarTech.com

StarTech.com CRJ4550PK Manual de usuario

Nohau

Nohau EMUL-IP2K-PC Manual de usuario

Foxun

Foxun SX-SP144E-HD4K2K Manual de usuario

Philips

Philips SWA3305W Manual de usuario

opticis

opticis Stretch DVIM1-1P0x Manual de usuario

Volkswagen

Volkswagen VAS 6558A Manual de usuario

NEXIBO

NEXIBO N-13 Manual de usuario

CYP

CYP PU-1H3HBTL Manual de usuario

Allen-Bradley

Allen-Bradley 1784-u2dhp Manual de usuario

Global Caché

Global Caché Flex Link Blaster Manual de usuario

Hauppauge

Hauppauge USB-Live2 Manual de usuario

Fenix

Fenix MPSV 15 Manual de usuario

BEGA

BEGA 71 085 Manual de usuario

Tesla

Tesla HPWC Manual de usuario

GAMERON

GAMERON LUXURY TV CABLE Manual de usuario

molex

molex Milli-Grid Dual row 87568 Series Manual de usuario

Burndy

Burndy Continental Industries thermOweld CRE-7 Manual de usuario