Sicunet Neptune Series Manual de usuario

Neptune Series Access Control Systems

Installation Instructions

for 1 Door Systems and 2 & 4 Door Systems

with Integrated Power Supplies

Document Number: 100100 REV A

Installation Instructions for 1 Door and 2 & 4 Door Systems with Integrated Power Supply Page 1

Table of Contents

Notifications...................................................................................................................................................4

Copyright...................................................................................................................................................4

Approvals...................................................................................................................................................4

Notice.........................................................................................................................................................4

Introduction....................................................................................................................................................5

Access Control Overview..........................................................................................................................5

System Overview.......................................................................................................................................5

2 4 Door Systems Specifications................................................................................................................6

Installation of 2 4 Door Systems................................................................................................................7

Installation Check List...............................................................................................................................7

Locating the Controller for Installation.....................................................................................................7

Mounting the Metal Enclosure – 2 4 Door Systems..................................................................................8

Tamper Detection......................................................................................................................................9

System Power............................................................................................................................................9

Power Fault Detection...............................................................................................................................9

Door Lock Power.......................................................................................................................................9

Fire Release Input....................................................................................................................................10

Battery Connection..................................................................................................................................10

Battery Warnings.....................................................................................................................................10

Input Power Connector............................................................................................................................11

Controller Power, Power Fault and Fire Cutout Connector.....................................................................11

Output Power Connectors........................................................................................................................12

Power Connection....................................................................................................................................13

Calculating Estimated Standby Time......................................................................................................13

Controller Features – 2 4 Door Systems..................................................................................................14

Controller Hardware Identification.........................................................................................................14

Controller Inputs......................................................................................................................................14

Controller Connectors..............................................................................................................................15

Input Wiring.............................................................................................................................................15

Request to Exit and Door Position Connectors.......................................................................................16

Power, Power Fault and Tamper Connector............................................................................................17

Controller Outputs...................................................................................................................................20

Output Wiring Requirements...................................................................................................................21

Door and Auxiliary Output Connectors...................................................................................................21

Adding 2 Door Expansion.......................................................................................................................23

1 Door System Specifications......................................................................................................................24

Installation of 1 Door Systems.....................................................................................................................25

Installation Check List.............................................................................................................................25

Locating the Controller for Installation...................................................................................................25

Mounting the 1 Door System.......................................................................................................................26

Controller Features 1 Door Systems............................................................................................................27

Controller Hardware Identification.........................................................................................................27

Controller Inputs......................................................................................................................................27

Controller Wiring Harnesses...................................................................................................................28

Input Wiring.............................................................................................................................................28

Controller Outputs Power Input..........................................................................................................32

Installation Instructions for 1 Door and 2 & 4 Door Systems with Integrated Power Supply Page 2

Output Wiring Requirements...................................................................................................................33

Powering On and Connecting to a Network.................................................................................................35

Preparing for the Network.......................................................................................................................35

Connecting to the Local Network............................................................................................................36

Adding Clients to Systems......................................................................................................................37

IP Installer................................................................................................................................................38

System Configuration and Programming................................................................................................39

Trouble Shooting..........................................................................................................................................40

Testing, Maintenance and Service................................................................................................................42

Parts List.......................................................................................................................................................42

Contact Warranty Information..................................................................................................................43

Installation Instructions for 1 Door and 2 & 4 Door Systems with Integrated Power Supply Page 3

Notifications

adapted or transmitted in any form without written permission from Sicunet, Inc.

Approvals

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates and can radiate radio frequency energy and if not

installed and used in accordance with the manual, may cause harmful interference. Operation of

this equipment in a residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at their own expense.

This Access Control System is compliant with Level I UL 294 listed devices and must be

installed in a controlled location.

Notice

This manual contains information regarding the basic installation and configuration of the

browser-based Access Control System. It must be read and completely understood before

installation or operation.

It is intended that this unit will be installed by persons trained and qualified to install access

control systems and has the skills and knowledge working with electrical circuits and safety

codes. Important safeguards and instructions in this manual cannot cover all possible situations

and conditions that occur during installation and use and it must be understood that common

sense and caution must be exercised by the person(s) installing, maintaining and operating the

equipment.

Installations must conform to all national and local building and electrical codes.

This manual is for installing 1 Door Systems and 2 & 4 Door Systems ith

integrated po er. Please refer to the appropriate sections for specific

installation instructions for your system.

Installation Instructions for 1 Door and 2 & 4 Door Systems with Integrated Power Supply Page 4

Introduction

Access Control Overvie

Access Control is the selective restriction to a place or resource such as a property, building or

room to authorized persons and is a matter of who, where, and when. An access control system

is used to automate access control using credentials, credential readers, electric door locks and

other devices. Administrators configure the system to determine who is allowed to enter or exit,

where they are allowed to exit or enter, and when they are allowed to enter or exit. When access

is granted, the door is unlocked for a predetermined time and transaction is recorded. When

access is denied, the door remains locked and the attempted access is recorded. Administrators

can then run reports on the recorded transactions to review activity for selected dates and times.

System Overvie

Controller models are available in variety of configurations starting from 1 Door models that

require a separate power supply to 2 & 4 Door models that include an integrated power supply

for the controller and door lock power. Most models can be ungraded after installation with

enhanced features, such as enhanced reporting or more users, using software license keys. All

controllers include tamper and power fault inputs, in and out readers, request to exit and door

position inputs for each door and auxiliary inputs and outputs. All controllers are designed to be

connected to a network using an Ethernet RJ45 connector and configured using the integrated

web server.

Controllers can be configured as either a server or a client. All systems require a server

controller. Some systems have the ability to add additional client controllers to increase the

number of doors, inputs or outputs or control elevators. The software license key is used by the

controller to determine if it is a server or a client. After logging in, the license information about a

can be determined by clicking on the license icon at the bottom of the web page.

Certain models offer a mobile APP that can be used to setup and configure, view logs, lock and

unlock doors and activate threat levels. In addition, some systems also offers a cloud service

that provides a portal where a users or dealer can log into and manage one or many systems

securely.

Client controllers communicate with the server controller via the local area network and are

configured through the server using a web browser on PC connected to the network. Once the

server or client controller is configured, they will function without a network connection or the

PC. The network and PC is only required for setup, configuration and reporting.

Installation Instructions for 1 Door and 2 & 4 Door Systems with Integrated Power Supply Page 5

2 & 4 Door Systems Specifications

General Specifications

Processor Quad Core Cortex, 1.5 GHz

Memory 1GB DDR3 & 8 GB eMMc

Operating System Embedded Linux

Transactions > 45 per Second

System Power Requirements 115VAC @ 1.5A

Operating Temperature 5 ºF to 95ºF (1 ºC to 35ºC)

Enclosure Size (W x H x D) 14.25 x 14.25 x 3.75 in ( 362 x 362 x 95 mm)

Model

2 Door Systems 4 Door Systems

2DM 2DMPL 4DM 4DMPL

Internal Power Supply Controller &

Readers Only

Controller,

Readers & 12V

and 24V DC for

Door Locks

Controller &

Readers Only

Controller,

Readers & 12V

and 24V DC for

Door Locks

Battery Backup Controller &

Readers Only

Controller,

Readers & Door

Lock

Controller &

Readers Only

Controller,

Readers & Door

Lock

Recommended Battery Type

(battery is not included) 12V, 7AH, Sealed Lead Acid

Readers (Wiegand) 4 Total, One In & One Out Reader

for Each Door

8 Total, One In & One Out Reader

for Each Door

Request to Exit (REX) Inputs 2 Total, One for Each Door 4 Total, One for Each Door

Door Position (status) Inputs 2 Total, One for Each Door 4 Total, One for Each Door

Auxiliary Inputs 2 Total, General Purpose 4 Total, General Purpose

Tamper Digital Input Yes, Prewired on Units with Integrated Power

Power Fault Digital Input Yes, Prewired on Units with Integrated Power

Door Lock Outputs 2 Form C Relay, 24V @ 2. A 4 Form C Relay, 24V @ 2. A

Auxiliary Outputs 2 Form C Relay, 24V @ 2. A 4 Form C Relay, 24V @ 2. A

Installation Instructions for 1 Door and 2 & 4 Door Systems with Integrated Power Supply Page 6

Installation of 2 & 4 Door Systems

Installation Check List

The list below provides a logical sequence for installing a system. This list cannot cover all

possible situations and conditions that occur during installation and use and it must be

understood that common sense and caution must be exercised by the person(s) installing,

maintaining and operating the equipment.

✔Calculate the systems power requirement by adding up the power required

for each device connected to the system to make sure the required power

can be provided by the system.

✔Mount the controller in a secure, controlled location

✔Connect the inputs and outputs

✔Connect the readers

✔Connect the door locks and auxiliary outputs

✔Connect power to the controller using a dedicated unswitched, grounded

outlet rated for 115 VAC @ 5 Amps

✔Obtain an IP address, Subnet Mask, DNS and other information from the

network administrator

✔Configure the controller's network settings

✔Connect the controller to the local area network

✔Add optional license keys to upgrade features

Locating the Controller for Installation

Choose a centrally located, secure, clean and dry area near an AC power source. Avoid

mounting the controller within 6 feet of any equipment that may generate electrical interference.

CA TION: The power supply used for the controller must only

be connected to an unswitched, rounded, 115 VAC outlet. If

an unswitched outlet is not available or within 6 feet of the

controller mountin location, have a licensed electrician install

an outlet per local codes. All wirin must be in accordance with

the National Electrical Code, NPFA 70 and all local codes. For

UL installations, the maximum Ethernet cable len th is 98.5

feet (30 meters).

NOTE: This device complies with Part 15 of the FCC Rules.

Operation is subject to the followin two conditions: (1) this

device may not cause harmful interference and (2) this device

must accept any interference received, includin interference

that may cause undesired operation.

Installation Instructions for 1 Door and 2 & 4 Door Systems with Integrated Power Supply Page 7

Mounting the Metal Enclosure – 2 & 4 Door Systems

The metal enclosure should be mounted vertically on a wall in a secure location. The

temperature in the mounting location must be within the system's specified limits. A minimum of

8 inches of space around all sides of the enclosure is recommended. Knockouts are provided

along the sides and top of the enclosure for routing wires. When running wires through the

knockouts, install bushings or conduit connectors as needed to protect wires from damage.

1. Run all wires to the enclosure location and label the wires according to their use.

2. Remove the enclosure's door by first unlocking the door and removing the door's ground

wire. The door may be lifted out of the hinge slots, which will provide room for mounting

and connecting wires to terminals.

3. Locate the enclosure on the wall and level. Mark the mounting holes on the wall and

remove the enclosure and install anchors appropriate for the type of wall and mounting

conditions.

4. DO NOT DRILL the mounting holes while the enclosure is in place on the wall. Dust and

debris from drilling will contaminate and damage the electronics.

5. Partially insert mounting screws into the top two mounting holes and hang the enclosure

on the screws. Check for level, insert the lower screws and tighten all four mounting

screws.

6. Run the wires through the knockout holes and connect to the appropriate terminals (see

following sections of the manual for wiring details). Note: Tie down loops are located in

the enclosure and are used to provide strain relief for field wiring connections to the

controller.

7. Reinstall the door and reconnect the door's ground wire.

CA TION: This equipment includes electronic components

that are sensitive to static electricity. Make sure to dischar e by

touchin an earth round before handlin this equipment.

NOTE: When locatin the controller, choose a centrally located,

secure, clean and dry area. Avoid mountin the controller within

6 fee (2 meters) of any equipment that enerates electrical

interference.

Installation Instructions for 1 Door and 2 & 4 Door Systems with Integrated Power Supply Page 8

2 & 4 Door System Features and Mountin Locations

(*There are two types of power modules, one with lock power and one without)

Tamper Detection

A tamper switch is mounted in the enclosure and is prewired to the controller. If the enclosure's

door is opened, the tamper switch will activate and signal the controller. The controller can be

configured using Event Actions to perform a system backup, activate an auxiliary output or send

an email notification when a tamper input is detected.

System Po er

The enclosure includes a 12 VDC 6.5 Amp (75W) power supply and Power Module. The power

module provides power to charge a 12V sealed lead acid battery (SLA, not included) that is

used for battery backup operation, power for door locks and power for the main controller and

accessories such as readers and keypads.

Po er Fault Detection

When the power power module detects an AC power loss, it will automatically change operation

over to battery backup and signals the controller that a power fault has occurred. The

controller's fault input can be configured using Event Actions to perform a system backup,

activate an auxiliary output or send an email notification. This is prewired at the factory.

Door Lock Po er

On models that include po er for the door locks, the power module has the ability to supply

either 12 or 24 VDC power to the door locks. This can be set individually for each of the four

outputs. LED's indicate if the output power is set to 12 VDC (GREEN LED), 24 VDC (AMBER

LED) or if the output is overloaded (RED LED). NOTE: The maximum output current for each

of the four outputs is 375 mA @ 24V or 700 mA @ 12V.

Installation Instructions for 1 Door and 2 & 4 Door Systems with Integrated Power Supply Page 9

TAMPER

SWITCH

MOUNTING

HOLE

MOUNTING

HOLE

MOUNTING

HOLE

MOUNTING

HOLE

POWER CORD

CONNECTOR

*POWER

MODULE

12V BATTERY

(NOT INCLUDED)

2 or 4 DOOR

CONTROLLER

GROUNDING POST

FOR READER

SHIELDS

Fire Release Input

On models that include po er for the door locks, the power module is prewired with a

normally closed Fire Release input. If the input is opened, power will be disconnected from the

connected door locks. This can be used to unlock fail safe door locks. Note: The power

module and/or access control system is not listed as and can not be used as a fire

warning system.

Battery Connection

The enclosure provides space and charging for one 12V sealed lead acid battery. The power

module monitors the battery to prevent over charging and excessive discharging. When primary

AC power is lost, the battery will provide standby power until the battery voltage reaches

approximately 11 VDC at which point the system will shutdown until main power is restored.

The amount of time standby power is supplied depends on the initial battery voltage and the

current draw of the devices connected to the system.

Battery Warnings

Use caution when installing the battery. Incorrect use can damage the battery, power

module or can cause shock or fire.

Connect main AC power before installing the battery. Depending on the condition of the

battery, the system may power up when connecting the battery without an AC power

connection.

Only connect one battery to the power module. Do not connect multiple batteries in

parallel or in series. This will damage the system and void the warranty.

The battery charger provides a maximum charge rate of approximately 9 mA and will

maintain the charge on a fully charged battery. Ensure that this does not exceed the

battery manufacture's rating.

Replace the backup battery every 2 to 3 years.

Properly dispose of old batteries.

The illustrations below show the features of the power module.

Installation Instructions for 1 Door and 2 & 4 Door Systems with Integrated Power Supply Page 1

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Controladores de acceso IP de Sicunet

Sicunet

Sicunet NEPTUNE Manual de usuario

Manuales populares de Controladores de acceso IP de otras marcas

ZKTeco

ZKTeco SpeedFace-V5L Manual de usuario

Jantar

Jantar REX A-1-9 Manual de usuario

2N Access Unit Hoja de instrucciones

Kedacom

Kedacom KSCA120 Series Manual de usuario

H3C

H3C WX2880X Manual de usuario

G4S

G4S S870-EX Guía

PRASTEL

PRASTEL M2000PE Manual de usuario

Allegion

Allegion interflex IF-281 Cylinder Manual de usuario

TECOM

TECOM TS1067E Manual de usuario

Fermax

Fermax Memokey 100C Guía del usuario

Fermax

Fermax CITYLINE MEMOKEY Manual de instrucciones

Software House

Software House iSTAR Pro 2U RM Manual de instrucciones

AKCP

AKCP SP+ Manual de usuario

Bpt

Bpt HNA/102 Manual de usuario

Civintec

Civintec CV9601T-T-1F Manual de usuario

BioMax

BioMax N-X90W Manual de usuario

ZKTeco

ZKTeco OP-200 Manual de usuario

FingerTec

FingerTec s-Kadex Manual de usuario