SI Nano Box Manual de usuario
INSTALLERS: Please leave this manual with the owner.
24v DC - Zigbee / RTS
Nano Box
Installation Instructions
Doc. # 400024
PARTS LIST
Parts list - Nano Box - 24v DC - RTS 1
Shades
Leveling Shims
(4 per shade)
Installation Remotes
(1 per RTS shade)
Wall Brackets
Spacer Blocks (optional - 4 per shade)
Terminal Block
Brackets
275 Box
375 Box
475 Box
Terminal Blocks
Screws Included
(3 per Bracket)
Longer Screws Included
Included remotes form factor may
vary, however RF functionality and
performance is consistent.”
OR
Please note all the Serial No.s on your Shade motors.
See the last page on these instructions.
2
Spacer Blocks - used to clear an obstruction in the fabric path.
Leveling Shims - used if the window frame is out of level.
Connect to shade brackets before installation
Note: do not use more than 2 leveling shims per bracket.
Note: Do not use more than 4 spacer blocks per bracket.
Connect spacer blocks to shade brackets before installation.
SPACER BLOCKS AND LEVELING SHIMS (OPTIONAL)
Spacer blocks and Leveling Shims
3. Make sure the wall bracket lever is down (may already be down).
INSTALLATION
1. Terminate pre-wire with the supplied terminal block.
Not
Used
Data For 24vDC Only
Header
Jamb
24
24
+
Installation - Nano Box - 24v DC - RTS 3
Proper position for
installing Box
2. Box bracket position is recommended 2”-4” from end caps.
2” - 4” 2” - 4”
4. Install terminal block bracket between jamb and wall bracket on the motor side using the
supplied screws
Jamb
Jamb
Header
Terminal block bracket must be on motor side.
4” - 6” 4” - 6”
INSTALLATION
Installation - Nano Box - 24v DC - RTS 4
5. Connect the shade and pre-wire connectors, then snap into the terminal block bracket
INSTALLATION
6. Hang shade onto wall brackets and center in opening
Installation - Nano Box - 24v DC - RTS 5
7. Use thumb to lock shade in place
Wiring - Nano Box - 24v DC - RTS
WIRING
24v DC
For guaranteed motor performance the supplied voltage for 24v motors must be 24v DC. See
the table below for maximum wire lengths.
If the motors are powered using a Kartos connect the motors to the “+v” and “-v” ports on the
terminal blocks.
Wire Gauge (AWG)
14
16
18
Maximum Supported Wire Length (FT.)
250
150
100
V+ Positive 24vDC
V- Negative 24vDC
6
2 Conductor Cable for each
Zigbee/RTS LV motor
V+
V-
V+
V-
V+
V-
V+
V-
Programming - Zigbee
The lower limit of every shade is preprogrammed to 1/2” from the bottom of the window. After
installing each shade, follow these steps to adjust the lower limit:
STEP 2 - Assign shades to groups :
All grouping of devices is completed within the TaHoma application:
1. Open the TaHoma application and navigate to the conguration tab.
2. Press the + symbol in the upper right corner.
3. Choose the Zigbee device type.
4. Select “Add Zigbee Group”.
5. Label the group.
6. Select the devices you would like to be included in this group.
STEP 3 - Pair devices or groups with a remote:
All pairing of devices and groups to remotes is completed within the TaHoma application. In
order to pair more than one shade to a channel, a group must be created rst.
1. Open the TaHoma application and navigate to the conguration tab.
2. Press the chain/link button next to the remote being congured.
3. Select the shade or group to pair from the list and deselect any other devices.
4. Quick press the programming button on the back of the remote and click OK in the application
to conrm.
NOTE: Each Zigbee Situo remote channel will be capable of pairing to a group containing up to 20 motors.
PROGRAMMING STEPS
(TaHoma/LinkPro Z must be plugged in and on the network)
Step 1: Fine tune lower limit.
Step 2: Assign shades to groups and remotes.
Step 3: Pair devices and groups with remotes.
STEP 1 - Fine tuning lower limit :
1. Click on the 3 dots in the lower right hand corner of the TaHoma app.
Note: You may see a pop-up warning window which could damage the shade.
2. In settings click on advanced settings.
3. Select the shade you want to set the limits to.
4. You only want to select and adjust the lower limit.
Note: Do not set upper limit or change rotation.
5. Press the down button in the app to move the shade to the Factory set lower limit.
6. Click Next.
7. Now make up or down adjustments to shade using the Up / Down increments. Each (button
press) adjustment can take a couple seconds, to execute. Once you are satised with the new
lower limit, press save Limit.
PROGRAMMING
Tech Support: 512.832.6939
For Zigbee
Problem Possible Cause Action to Take
TaHoma LED is Red. No internet
connectivity.
Check network connection to the internet, and ensure
the TaHoma is properly connected via ethernet or
Wi.
Shade won’t operate. Low-voltage power
supply
Verify wiring, terminations and AC power connections
to your power supply.
TROUBLESHOOTING
TROUBLESHOOTING WITH SUPPORT
With our Support team guidance, you may be instructed to
press the motor programming button using a thin tool (e.g. a
paperclip). If instructed, pressing this button for 2 seconds, can
take the motor out of delivery mode and will result in 1 jog.
Note: Under no circumstances, should you hold this
programming button for more than 2 jogs.
Technical Support: 512.832.6939 screeninnovations.com
Please use this QR Code
to access the updated
installation instructions
thin
tool
Otros manuales para Nano Box
5
Otros manuales de Persiana de ventana de SI
Manuales populares de Persiana de ventana de otras marcas
Domondo
Domondo PureNight Manual de instrucciones de instalación
rollease acmeda
rollease acmeda Easy Spring Air Guía de configuración
IKEA
IKEA KADRILJ Manual de usuario
Hallis Hudson
Hallis Hudson Rolls Super glide Manual de usuario
Benthin
Benthin P1614 Manual de usuario
MV LINE
MV LINE CLARA 015 Manual de instrucciones
