SI Zen 2 Pocket Manual de usuario
Zen 2 Pocket
Installation Instructions
INSTALLERS: PLEASE LEAVE THIS MANUAL WITH THE OWNER.
Zipper Tracks and Cable Guides
Doc. # 400163 |v. 1.2 |15 June 2022
Screen Innovations warrants its products, to the original purchaser only, to be free from defects in
materials and workmanship for a period of one (1) year from the date of purchase by the original
purchaser provided they are properly operated according to Screen Innovations' instructions and are not
damaged due to improper handling or treatment after shipment from the factory.
This warranty does not apply to equipment showing evidence of misuse, abuse, or accidental damage,
or which has been tampered with or repaired by a person other than authorized Screen Innovations
personnel.
Screen Innovations’ sole obligation under this warranty shall be to repair or to replace (at Screen
Innovations’ option) the defective part of the merchandise. Returns for service should be made to
your Screen Innovations' dealer. If it is necessary for the dealer to return the screen or part to Screen
Innovations, transportation expenses to and from Screen Innovations are payable by the purchaser and
Screen Innovations is not responsible for damage in shipment. To protect yourself against damage or
loss in transit, insure the product and prepay all transportation expenses.
This warranty is in lieu of all other warranties, express or implied, including warranties as to tness
for use and merchant ability. Any implied warranties of tness for use, or merchantability, that may be
mandated by statute or rule of law are limited to the one (1) year warranty period. This warranty gives
you specic legal rights, and you may also have other rights, which vary from state-to-state. No liability
is assumed for expenses or damages resulting from interruption in operation of equipment, or for
incidental, direct, or consequential damages of any nature.
In the event that there is a defect in materials or workmanship of a Screen Innovations product, you may
contact our Sales Partners at 9715-B Burnet Road Suite 400, Austin, TX 78758, (512) 832-6939.
Important: this warranty shall not be valid and screen innovations shall not be bound by this warranty if
the product is not operated in accordance with screen innovations' written instructions.
Keep your sales receipt to prove the date of purchase and your original ownership.
Limited 1 year warranty
on Screen Innovations products
Technical Support: 512.832.6939 screeninnovations.com
Please use this QR Code
to access the updated
installation instructions
and related documents.
Operating and Care of Your Shade� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 1
Before Proceeding � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �2
Parts in the Box � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �3
Installation – Mount the Brackets� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4
Installation – Mount the Cassette � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �5
Installation – Material Roll � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6 – 7
Installation – Zipper Tracks � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8 – 11
Installation – Cable Guides� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �13 – 14
Line Voltage (110v AC/ 60 Hz) wiring � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 15
Line Voltage (AC - 485 Control) wiring � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �16
Controls Guide Reference � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �17
TABLE OF CONTENTS
1
OPERATING AND CARE OF YOUR SHADE
Operation of the shade systems should only be performed by responsible parties.
Always check the path of the Zen 2 Shade before operating to ensure that the path is clear of furniture or
obstacles that could prevent full operation. Monitor the Zen 2 Shade for smooth operation through its entire
range. Operating a Zen 2 Shade unattended may lead to damage from obstructions or other causes.
DO NOT lower Zen 2 Shades during high wind conditions (depends on fabric and site, but general rule is 20
system is currently in the down position, it is usually okay to operate the shade and retract it. However, avoid
operation at any time high wind conditions are present for proper operation.
For Zen 2 Zipper Guide– Side Track maintenance is important to ensure proper operation and trouble-free
performance of the Zipper track system. An annual or bi-annual cleaning of the side tracks is recommended,
clearing any debris and/or dirt/dust that has built up in the track housing and zipper inserts. Light power
Fabric maintenance and cleaning– Zen 2 Shade fabric is subject to weather, bugs, and debris under normal
use or in storage, requiring occasional maintenance and cleaning. While fading and wear over time are
normal, debris and pests could accelerate this wear. Shade fabrics can be rinsed with a hose to clean off
debris. A pressure washer with a low pressure nozzle and light, fabric-safe soap may also be used. Scrubbing
with a bristle brush or pad is not recommended.
Fabric maintenance– Cable and No-guide– Cable guide and No-guide shades require occasional
maintenance to the cut ends of the fabric. The frequency depends on the fabric, environment, and use.
Simply trim the edges with a blade or scissors and cauterize the frays with a lighter or heat gun. Be careful
not to leave the heat source on the material too long, or it may damage the material.
Power Cable — The power cable for motor is shipped disconnected inside of the box for ease of material
inside of box on the ground before mounting the shade to ensure no obstacles impede access when shade is
installed.
2
Preparing for installation– It is crucial that all installations are planned out carefully before
specifying a shade order.
channels.
Make sure that the tracks and the shade boxes can be installed securely, level, and plumb. Add appropriate
blocking or carpentry work before installing tracks and shades.
poor operation.
Electrical work should be performed following appropriate electrical codes and regulations by a licensed
electrical professional.
Use fasteners appropriate for the structure the Zen 2 shade will be mounted to.
Do not use any sharp blades when opening the packaging.
We recommend a pocket size of 7” W x 10” H.
Read the instructions in their entirety before proceeding. Actions contrary to the instructions invalidate
the warranty and may result in serious damage and/or injury.
BEFORE PROCEEDING
3
(2) Pocket
Brackets
(6) Spacer Blocks
Longer Screws
Case Assembly Left and Right Zipper
Track Assemblies
Needs to be the same as for the bOx
Mounting Bracket Options Cable Guides Only
Motor Slider
PARTS IN THE BOX – ZEN 2 POCKET
Shades Zipper Tracks
Only
(2) Cables
(2) L Brackets
(6) Mounting
Screws
Accessories Options Required
Hardware
Programming
Remote (RTS
shades)
RJ 45 Coupler
(485 shades)
4
INSTALLATION – MOUNT THE BRACKETS
Ceiling MountJam Mount
1Use appropriate fasteners to mount to the ceiling or wall 1.5” less than the ordered shade width.
BEFORE INSTALL– check upper corners of the pocket as necessary to ensure no interference issues
with brackets.
NOTE: Ensure the fasteners used are adequate for the weight of the Zen 2 Shade and the structure.
5
Avoiding sharp tools, remove the roll from its packaging on a soft, clean surface. Discard any foam
or excess packaging.
Installation requires two or more people and/or hoisting equipment.
Please use safe lifting and rigging techniques.
2+
2
INSTALLATION – MOUNT THE CASSETTE
6
After pocket brackets are mounted, slide in the material roll along with the mounting plates on
each end.
3
4
INSTALLATION – THE MATERIAL ROLL
7
INSTALLATION – THE MATERIAL ROLL
Use the thumb screws to secure both ends.
Fasten the thumb screws on the mounting plates to secure the material roll.
5
Tabla de contenidos
