Shuttle HOT-597 Manual de usuario

- 45 -

HOT-597

Pentium™processor

Based AGP MAIN BOARD

User's Manual

- 1 -

NOTICE

Manual Ver 1.0

All information, documentation, and specifications contained in this manual are subject to change without prior

notification by the manufacturer.

The author assumes no responsibility for any errors or omissions which may appear in this document nor does it make a

commitment to update the information contained herein.

TRADEMARKS

All the brands and product names referred to in this manual are trademarks or registered trademarks of their respective

holders.

FCC Notice:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy. If not installed and used properly, in strict accordance

with the manufacturer's instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interfer-

ence by one or more of the following measures :

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/television technician for help and for additional suggestions.

The user may find the following booklet prepared by the Federal Communications Commission helpful "How to Identify and

Resolve Radio-TV Interference Problems." This booklet is available from the U.S. Government Printing Office. Washington,

DC 20402, Stock 004-000-00345-4

FCC Warning

The user is cautioned that changes or modifications not expressly approved by the manufacturer could void the users authority

to operate this equipment.

Note : In order for an installation of this product to maintain compliance with the limits for a Class B device, shielded cables

and power cord must be used.

CE Notice:

Following standards were applied to this product, in order to achieve compliance with the electromagnetic compatibility :

- Immunity in accordance with EN 50082-1: 1992

- Emissions in accordance with EN 55022: 1987 Class B.

- 2 -

TABLE OF CONTENTS

PREFACE ....................................................................................................................3

CHAPTER 1 FEATURES..................................................................................................4

Accessories of HOT-597 ......................................................................................................................6

CHAPTER 2 HARDWARE INSTALLATION............................................................................. 7

Jumper Setting......................................................................................................................................7

CPU Configurations Table....................................................................................................................8

CPU Configurations - SW1, JA26 & J19.............................................................................................8

System Clock and CPU Multiplier Manual Setting - SW1 & JA26...................................................14

SDRAM Frequency Setting - JP9.......................................................................................................15

CPU Voltage Manual Setting - J19.....................................................................................................16

Flash EEPROM Vpp - JP5.................................................................................................................17

Clear CMOS - JP2..............................................................................................................................17

Connectors..........................................................................................................................................18

CHAPTER 3 MEMORY CONFIGURATION ........................................................................... 21

CHAPTER 4 FLASH UTILITY..........................................................................................22

CHAPTER 5 VIA VXD AGP DRIVER INSTALLATION ......................................................... 24

CHAPTER 6 BIOS SETUP ...........................................................................................25

Main Menu .........................................................................................................................................26

Standard CMOS Setup........................................................................................................................28

BIOS Features Setup...........................................................................................................................30

Chipset Features Setup........................................................................................................................32

Power Management Setup..................................................................................................................35

PNP / PCI Configuration Setup..........................................................................................................38

Integrated Peripherals.........................................................................................................................41

Password Setting.................................................................................................................................44

- 3 -

HOT-597 is a high performace, cost effective, and energy efficient mainboard for the imple-

mentation of AGP, PCI, and ISA in desktop personal computer systems from 66MHz to

100MHz based on 64-bit Socket-7 super-scalar processors.

HOT-597 mainboard is a highly integrated IBM PC/ATX compatible ATX form-factor

system board designed to meet the industry's most demanding desktop applications. Based

on the VIA's MVP3 chipset.

HOT-597 accept AMD K6-2, K6, K5, Intel Pentium P54C, Pentium MMX, IDT-C6 and

Cyrix/IBM 6x86, 6x86L, 6x86MX processors and also features high-performance pipelined

burst secondary cache memory support with size of 1024KB. The memory subsystem is

designed supports standard Fast Page Mode (FPM), EDO, SDRAM, and 100MHz SDRAM.

HOT-597 complies with the Accelerated Graphics Port Specification 1.0 and features

support for 66/68/75/83/95/100MHz CPU bus frequencies and the 66MHz AGP bus fre-

quency.

HOT-597 provides a new level of I/O integration. VIA MVP3 chipset provides increased

integration and improved performance over other chipset designs.

The VIA's MVP3 chipset provides an integrated Bus Mastering IDE controller with two high

performance Ultra 33 DMA IDE interfaces for up to four IDE devices.

The onboard I/O controller provides the standard PC I/O functions: floppy interface, two

FIFO serial ports, an IrDA device port and a SPP/EPP/ECP capable parallel port.

Up to four PCI local bus slots provide a high bandwidth data path for data-movement

intensive functions such as graphics, and up to three ISA slots complete the I/O function.

HOT-597 provides the foundation for cost effective, high performance, highly expandable

platforms, which deliver the latest in Pentium processor and I/O standard.

PREFACE

- 4 -

FEATURES

HOT-597 Mainboard is carefully designed for the demanding PC user who wants high perfor-

mance and many intelligent features in a compact package:

Chipset

Features VIA's 82C598MVP Chipset with I/O subsystems

Main Processor

AMD K6-2 266~450 MHz, AMD K6 166~300 MHz, K5 PR133~PR166,

Intel Pentium (P54C) 100~200 MHz, Pentium MMX (P55C) 166~233 MHz,

Cyrix/IBM 6x86 P166+~P200+, 6x86L P166+~P200+, 6x86MX PR200~PR333,

IDT-C6 200~225MHz

Secondary Cache

Onboard 512KB or 1024KB Pipelined Burst Cache.

Versatile Memory Supports

Equipped with three DIMM sockets for (8, 16, 32, 64 or 128MB) 168-pin 66MHz or

100MHz PC SDRAM memory modules up to 384 MB.

Expansion Slots

Provides four 32-bit PCI slots, three 16-bit ISA slots and one AGP slot.

AGP (Accelerated Graphics Port)

AGP Specification 1.0

HOT-597 main board equipped with an AGP slot for an AGP VGA card that supports

133MHz 2X mode for texture mapping z-buffering and alpha blending. AGP allows 3D

applications to run faster and smoothly.

Onboard I/O Chip

One Floppy port

One PS/2 mouse and Keyboard connector

Two high-speed UART compatible serial port

Serial Port 2 can also be directed from COM2 to the Infrared Module for wireless connec-

tions One parallel port with ECP and EPP capabilities

Onboard PCI Bus Master IDE Controller

Two Ultra DMA/33 Bus Master IDE Ports supports four IDE devices up to 33 MB/sec

IDE transfers and supports Enhanced PIO Modes 3 and 4 and Bus Master IDE DMA

Mode 2 devices

Onboard 20-pin ATX Power Supply

ATX power supply unit can connect to the 20-pin ATX power connector onboard, sup-

porting Suspend and soft-on/off by dual-function power button.

- 5 -

AdvancedPower Management

Features three power savings modes:Doze, Standby, and Suspend.

SupportsACPI (Advanced Configuration and Power Interface) function.

ACPI provides more efficient Energy Saving Features controlled by your operating

system theat supports OS Direct Power Management (OSPM) functionality.

System BIOS

Provides licensed Award BIOS V4.51PG on 2MB Flash EEPROM.

Supports Green PC, Desktop Management Interface (DMI), PnP, ACPI, NCR SCSI

BIOS and Virus Protection.

Board Size:

ATX form factor size 305mm x 190mm.

- 6 -

ACCESSORIES OF HOT-597

Figure 1

- 7 -

HARDWARE INSTALLATION

Figure 2-1

board.

The following examples show the conventions used in this chapter.

Finger 3 set to ON,

the others set to OFF

Finger 4, 6 set to ON,

the others set to OFF

Insert a jumper pack on J19

Row 2-3 to set CPU voltage

auto-detecting

Remove jumper pack from J19

and insert mini on pin A, C, D on

Row 1-2 to set voltage on 3.3V Table 2-1

This chapter is designed for explaining how to configure the HOT-597 hardware. After you install the

main board, you can set jumpers, install memory on the main board, and make case connectors. Refer to

this chapter whenever you upgrades or reconfigure your system.

JumperSetting

This section describe the necessary procedures and proper jumper settings to configure the HOT-597

main board.

Jumper pin headers show on right side are used to

configure system clock, CPU multiplier voltages and

SDRAM clock speed.

System Clock and CPU Clock Multiplier - SW1

DIP siwtch finger 1 to finger 3 are used to adjust

System Clock from 66 to 100 MHz, finger 4 to finger 6

used to adjust CPU Clock Multiplier from 1.5x to 5.5x.

CPU Voltages - J19

Jumper group J19 are used to adjust onboard voltages

output from Switching regulators to CPU.

Futher more, HOT-597 Mainboard provide intelligent

CPU Voltages detecting and auto-adjusting function.

Enable this function by inserting a mini jumper pack on J19 row 2/3 (factory default), none of other mini

jumpers are required on jumper group J19. HOT-597 Mainboard will assign proper voltages to CPU

automatically.

SDRAM Clock Speed - Jumper JP9

HOT-597 support 100MHz external clock speed AMD 266MHz and 400MHz K6-2, and which allows

the user to use 66MHz normal SDRAM DIMM or 100MHz PC/100 SDRAM DIMM. Jumpers JP9 are

used to set SDRAM DIMM clock speed synchronous with System Clock (CPU External Clock) or

synchronous with AGP Clock.

Those hardware settings are made through the use of jumper caps to connect jumper pins on the main

- 8 -

ProcessorSpeedSystem

Clock MultiplierProcessorSpeedSystem

Clock Multiplier

Intel

Pentium

P55CMMX

233 MHz66 MHz3.5x

AMDK6-2

450 MHz100 MHz4.5x

Cyrix/IBM

6x86MX

PR333 100 MHz2.5x

200 MHz66 MHz3x400 MHz100 MHz4xPR333 83 MHz3x

166 MHz66 MHz2.5x380 MHz95 MHz4xPR300 75 MHz3x

Intel

Pentium

P54C

200 MHz66 MHz3x366 MHz66 MHz5.5xPR300 66 MHz3.5x

166 MHz66 MHz2.5x350 MHz100 MHz3.5xPR266 83 MHz2.5X

133 MHz66 MHz2x333 MHz95 MHz3.5xPR266 66 MHz3.5X

100 MHz66 MHz1.5x333 MHz66 MHz5xPR233 75 MHz2.5x

IDT-C6225MHz75 MHz3x300 MHz100 MHz3xPR233 66 MHz3x

200MHz66 MHz3x300 MHz66 MHz4.5xPR200 75 MHz2x

AMDK6

300 MHz66 MHz4.5x266 MHz66 MHz4xPR200 66 MHz2.5x

266 MHz66 MHz4x

AMDK5

PR166 66 MHz2.5x

Cyrix/IBM

6x86 (L)

P200+75 MHz2x

233 MHz66 MHz3.5xPR133 66 MHz1.5xP166+66 MHz2x

200 MHz66 MHz3x

166 MHz66 MHz2.5x

CPU Configuration Table

CPU Configuration - SW1, JA26 & J19

SW1 and J19 are the Jumpers that you need to set your CPU on HOT-597. Make sure that you know

the type of CPU that you are installing and refer to the proper settings which are listed below.

Normally, CPU voltage is auto-detected on HOT-597 and is set to Auto-detected when HOT-597 is

delivered. If you have a higher frequency CPU or you want to set CPU frequency and voltage

manually, please refer to next two sections.

AMD-K5 Series CPUs Settings

ProcessorSpeedFrequency Setting

SW1,JA26

JumperBlock J19

Vcore/Vio

Auto-detect

AMD-K5

PR166

66MHzx2.5

3.52V/3.52V

PR133

66MHzx1.5

Table 2-3

Table 2-2

- 9 -

ProcessorSpeedFrequency Setting

SW1,JA26

JumperBlock J19

Vcore/Vio

Auto-detect

AMD K6

300 MHz

66MHzx4.5

2.2V/3.3V

266 MHz

66MHzx4

233 MHz

66MHzx3.5

233 MHz

66MHzx3.5 3.2V/3.3V

200 MHz

66MHzx3

2.9V/3.3V

166 MHz

66MHzx2.5

Table 2-4

AMD-K6 Series CPUs Settings

Note :The voltage of AMD-K6 233MHz may vary from market and CPU core.

Please ask your CPU provider for detail.

Tabla de contenidos

Otros manuales de Placa madre de Shuttle

Shuttle

Shuttle FB52 Manual de usuario

Shuttle

Shuttle Spacewalker FE22 Manual de usuario

Shuttle

Shuttle MV43P Manual de usuario

Shuttle

Shuttle FN85 Manual de usuario

Shuttle

Shuttle Spacewalker AV30 Manual de usuario

Shuttle

Shuttle Spacewalker HOT-687 Manual de usuario

Shuttle

Shuttle AV18 Manual de usuario

Shuttle

Shuttle Spacewalker AV40 Manual de usuario

Shuttle

Shuttle AK37GT Manual de usuario

Shuttle

Shuttle HOT-679 Manual de usuario

Shuttle

Shuttle Spacewalker HOT-685Z Manual de usuario

Shuttle

Shuttle MV43VN Manual de usuario

Shuttle

Shuttle MV21 Manual de usuario

Shuttle

Shuttle ME21 Manual de usuario

Shuttle

Shuttle FB86 Manual de usuario

Shuttle

Shuttle FB61 Manual de usuario

Shuttle

Shuttle HOT-603 Manual de usuario

Shuttle

Shuttle HOT-565 Manual de usuario

Shuttle

Shuttle FN41V3 Manual de usuario

Shuttle

Shuttle FN45U Manual de usuario

Shuttle

Shuttle AV64 Manual de usuario

Shuttle

Shuttle AB60P Manual de usuario

Shuttle

Shuttle FT62 Manual de usuario

Shuttle

Shuttle FB54 Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario