Shure MXA901-R Manual de usuario

MXA901-R

Ceiling Array Microphone

Online user guide for MXA901-R.

Version: 0.1 (2024-A)

Shure Incorporated
2/42
Table of Contents
MXA901-R   Ceiling Array Microphone 4
General Description 4
Features 4
Getting Started 4
Videoconferencing Room Equipment 4
MXA901 Designer Setup Example 6
MXA901 Web Application Setup Example 8
MXA901-R Parts 11
Power Over Ethernet (PoE) 12
Model Variations 12
Optional Accessories 12
What's in the Box 12
Reset Button 13
Reset Modes 13
MXA901 Control Software 13
Control Devices with Shure Designer Software 14
MXA901 Coverage 14
How Much Space Does the MXA901 Cover? 15
Using Autofocus™ to Improve Coverage 15
Use Case: 2 MXA901s in a Room 15
Use Designer's Auto Route 16
Adjust Microphone Levels 17
Mute the MXA901 17
How to Install the MXA901 18
Install the MXA901-R on a Ceiling 19
VESA Standardized Mounting 22
Dante Channels 22
IntelliMix DSP 22
DSP Best Practices 23
Acoustic Echo Cancellation 23
Noise Reduction 24
Automatic Gain Control (AGC) 24
Delay 24
Compressor 25
Parametric Equalizer 25
Mute Sync 27
Encryption 28
Set Up the 802.1X Protocol for a Device 29
Turn Off or Clear 802.1X Settings 30
Change 802.1X Settings 30
Troubleshooting 802.1X Setup Issues 30
Networking Best Practices 30
Switch and Cable Recommendations for Dante Network
ing 31
Device IP Configuration 31
Setting Latency 31
QoS (Quality of Service) Settings 32
IP Ports and Protocols 32
Digital Audio Networking 33
Compatibility with Dante Domain Manager 33
Dante Flows for Shure Devices 33
AES67 34
Sending Audio from a Shure Device 35
Receiving Audio from a Device Using a Different Audio 
Network Protocol 35
Using Command Strings 35

Shure Incorporated

3/42

Troubleshooting 35

Additional Resources 36

Specifications 37

MXA901-R Frequency Response 38

Dimensions 39

Important Safety Instructions 39

Important Product Information 40

Introduction to EMC 40

Environmental Regulatory Information 42

Shure Incorporated

4/42

•

MXA901-R

Ceiling Array Microphone

General Description

Our sleekest ceiling array microphone yet, the MXA901 provides superb AV conferencing audio in a discreet and stylish 13.5-

inch round form factor that complements any interior design. Single-Zone Automatic Coverage technology captures talkers

clearly with no setup. Use one MXA901 in smaller rooms or multiple units in larger spaces. Onboard IntelliMix®DSP delivers

echo- and noise-free audio, while next-generation array architecture ensures natural speech and enhanced directional pickup.

Features

Single-Zone Automatic Coverage technology captures audio from a 20 by 20-foot (6 by 6 meter) area out of the box

Onboard IntelliMix DSP with acoustic echo cancellation, noise reduction, automatic mixing, automatic gain control, and EQ

for echo- and noise-free audio

Round 13.5-in. diameter (34 cm) form factor with white, black, or aluminum finish

Onceiling mounting bracket included; versatile options for onceiling, inceiling, pole, rod, or suspension mounting avail

able

Shure Designer System Configuration software for easy setup and configuration

Embedded web application for setup flexibility

LED status bar with configurable colors and brightness

Dante and AES67 audio networking protocols

Getting Started

Videoconferencing Room Equipment

Your Microflex®microphone is one part of a complete room system for videoconferencing. It's helpful to think about all the parts

of your room system as you get started setting up the microphone.

™

Shure Incorporated

5/42

•

◦

•

Medium room equipment example

A standard room includes some or all of this equipment:

Microphone(s)

DSP or other processor

Loudspeakers (networked or analog)

Computer with videoconferencing software

Network switch

Camera

Other accessories such as table mute buttons, tablets to control meetings, and other peripherals

The Microflex Ecosystem offers a complete portfolio of networked audio solutions that can be precisely tailored to your needs.

What Software Do I Need to Set Up This Microphone?

Install this software on a computer that connects to the same network as the microphone:

Control software to adjust microphone settings. This microphone has 2 options:

Option 1: Shure Designer

Use for managing lots of Shure devices in 1 place

Control Shure devices and route audio between them

Create rooms to manage devices and design coverage

Option 2: Web application (open using Shure Web Device Discovery)

Use to manage each Shure device separately

Control each device individually with its web application

Route audio using Dante Controller

Dante Controller to send audio signals to other Dante devices. Not necessary if you're only routing audio to Shure de

vices in Designer.

Shure Incorporated

6/42

•

Shure Web Device Discovery to easily find device web applications. Not necessary if you're only using Designer.

Shure Update Utility to update firmware on Shure devices (download at shure.com/suu)

MXA901 Designer Setup Example

This example uses Shure Designer 6.0 software to set up an MXA901, an ANIUSB-MATRIX, and 2 MXN5-C loudspeakers. You

might use Designer if:

You're managing many Shure devices in different spaces

You're routing audio between many Shure devices

You can use other combinations of devices with the MXA901, but the setup process in Designer is similar.

After completing this basic setup process, you should be able to:

Access the MXA901 in Designer

Route audio and adjust DSP settings

Understand the basic workflow for working with devices in Designer

This example uses:

Cat5e (or better) Ethernet cable

Network switch that provides Power over Ethernet (PoE)

Computer with Designer 6.0 or newer (download at shure.com/designer)

Computer with videoconferencing software

ANIUSB-MATRIX

2 MXN5-C loudspeakers

Step 1: Install and Connect

The MXA901 has a 20 x 20-foot (6.1 x 6.1 m) coverage area. The maximum recommended mounting height is 12 feet (3.7 m).

The microphone intelligently adjusts coverage for all talkers in the coverage area. IntelliMix DSP ensures a clear signal for the

far end with AEC, noise reduction, and more.

Install the MXA901 and other devices. Connect all devices to PoE ports on the network switch using Ethernet cable.

Connect the computer running Designer to the same network.

Open Designer. Check that you’re connected to the correct network in File > Designer preferences.

Open a new design and drag the devices into the design.

Shure Incorporated

7/42

◦

Step 2: Route Audio and Apply DSP

The easiest way to route audio and apply DSP is with Designer's auto route feature. This feature routes audio signals, applies

DSP settings, turns on mute synchronization, and enables LED control for connected devices.

Select Auto route. Designer makes the following routes:

MXA901 to ANIUSB-MATRIX

ANIUSB-MATRIX USB output to computer with videoconferencing software

ANIUSB-MATRIX Dante output to MXA901 AEC reference and MXN5-C loudspeakers

You can also route audio manually in Designer or use Dante Controller.

Check the audio routes, matrix mixer routes, and other settings to make sure they fit your needs.

Select Deploy and connect to send the settings to the installed devices. Designer walks you through associating the de

sign devices with the online devices.

Step 3: Listen and Adjust

Connect the computer with videoconferencing software (such as Zoom or Microsoft Teams) to the ANIUSB-MATRIX's

USB port.

Open the videoconferencing software on the computer connected to the ANIUSB-MATRIX. In the settings, choose the

ANIUSB-MATRIX as the speaker and microphone.

Place a test call with the whole system and have the far-end caller tell you how your microphone signal sounds. Make

gain, EQ, or DSP adjustments in the MXA901's IntelliMix tab.

Shure Incorporated

8/42

•

If needed, move the microphone's coverage area in the room's Coverage tab.

You can also listen to the microphone signal directly using a Dante headphone amp to help make adjustments.

MXA901 Web Application Setup Example

This example uses device web applications and Dante Controller to connect an MXA901 and an ANIUSB-MATRIX. You might

use web applications and Dante Controller if:

You don't have many Shure devices to manage

You need to route audio to third-party Dante devices

You can use other combinations of devices with the MXA901, but setup process is similar if you're working with web applica

tions and Dante Controller. After completing this basic setup process, you should be able to:

Open the MXA901's web application

Route audio and adjust DSP settings

Understand the basic workflow for working with device web applications and Dante Controller

This example uses:

Cat5e (or better) Ethernet cable

Network switch that provides Power over Ethernet (PoE)

Computer with Shure Web Device Discovery and Dante Controller software

ANIUSB-MATRIX

Step 1: Install and Connect

The MXA901 has a 20 x 20-foot (6.1 x 6.1 m) coverage area. The maximum recommended mounting height is 12 feet (3.7 m).

Shure Incorporated

9/42

◦

The microphone intelligently adjusts coverage for all talkers in the coverage area. IntelliMix DSP ensures a clear signal for the

far end with AEC, noise reduction, and more.

Install the MXA901 and other devices. Connect devices to PoE ports on the network switch using Ethernet cable.

Connect a computer with Shure Web Device Discovery and Dante Controller software to the same network.

Open Shure Web Device Discovery. Find the MXA901 in the list of devices and double-click to open the microphone's

web application.

Step 2: Route Audio

Use Dante Controller to route audio to and from other Dante devices. We'll route the MXA901's microphone signal to an

ANIUSB-MATRIX for this example.

Open Dante Controller and find both devices in the list of transmitters and receivers.

Make these routes:

MXA901 automix output to ANIUSB-MATRIX input

ANIUSB-MATRIX output to MXA901 AEC reference input. The AEC reference signal is usually the same one that

feeds the room's loudspeakers.

Send audio from the ANIUSB-MATRIX to other sources using the ANIUSB-MATRIX's matrix mixer. Open the ANIUSB-

MATRIX web application with Shure Web Device Discovery. A common destination is a computer connected by USB

with videoconferencing software (such as Zoom or Microsoft Teams).

Shure Incorporated

10/42

In your videoconferencing software, select the correct microphone and loudspeaker sources.

Step 3: Listen and Adjust

Place a test call with the whole system and have the far-end caller tell you how your microphone signal sounds. Make

gain, EQ, or DSP adjustments in the MXA901's IntelliMix tab.

If needed, move the microphone's coverage area in the Coverage tab.

You can also listen to the microphone signal directly using a Dante headphone amp to help make adjustments.

Tabla de contenidos

Otros manuales de Micrófono de Shure

Shure

Shure Microflex MX391 Series Manual de usuario

Shure

Shure Unisphere I PE566 Manual de usuario

Shure

Shure BETA 181 Manual de usuario

Shure

Shure PGA 48 Manual de usuario

Shure

Shure SM90 Manual de instrucciones

Shure

Shure PGA31 Manual de usuario

Shure

Shure Beta 58 Manual de usuario

Shure

Shure KSM42 Manual de usuario

Shure

Shure Microflex MX391 Series Manual de usuario

Shure

Shure KSM32 Manual de usuario

Shure

Shure Microflex MX300 series Manual de usuario

Shure

Shure 588SDX Manual de usuario

Shure

Shure WH20 Manual de usuario

Shure

Shure KSM44A Manual de usuario

Shure

Shure KSM141 Manual de usuario

Shure

Shure Microflex MX400SMP Manual de usuario

Shure

Shure M68P Manual de usuario

Shure

Shure MX1BP Manual de usuario

Shure

Shure KSM32 Manual de usuario

Shure

Shure WCM16 ISOMAX Manual de usuario

Shure

Shure PGA 56 Manual de usuario

Shure

Shure 526T Series II Super Punch Manual de usuario

Shure

Shure Microflex MX395 Manual de usuario

Shure

Shure SM89 Manual de usuario

Manuales populares de Micrófono de otras marcas

IK Multimedia

IK Multimedia iRig Stream MIC PRO Manual de usuario

DAPAudio

DAPAudio RM-101 Manual de usuario

AKG

AKG CHM 21 Manual de usuario

Sennheiser

Sennheiser evolution wireless series EM 100 Manual de usuario

Sony

Sony C-48 Manual de usuario

GIGAMEDIA

GIGAMEDIA GGM PAMICUHFG Manual de usuario

auna PRO

auna PRO MIC-900 Manual de usuario

AKG

AKG D 3800 Manual de usuario

MAIIN SOUND

MAIIN SOUND IIN style Manual de usuario

Earthworks

Earthworks TC25 Manual de usuario

Sennheiser

Sennheiser evolution D1 Manual de usuario

Alesis

Alesis MicLink Wireless Manual de usuario

DSPPA

DSPPA D6234 Manual de usuario

Monacor

Monacor IMG STAGELINE ECM-300B Manual de usuario

Ansr Audio

Ansr Audio Scan16 Manual de usuario

JLab

JLab GO TALK Manual de usuario

Renkforce

Renkforce TY-109 Manual de usuario

Trust

Trust 31008 Manual de usuario