Shure Microflex MX415DUAL Manual de usuario
MX415DUAL
Dual-Capsule Gooseneck Microphone
User guide for MX415DUAL.
Version: 0.1 (2021-G)
Shure Incorporated
3/10
•
•
•
•
•
•
MX415DUAL
Dual-Capsule Gooseneck Microphone
General Description
The Shure Microflex MX415DUAL dual-capsule gooseneck microphone features two electret condenser cartridges mounted
in a single low-profile housing and two preamp-equipped outputs providing redundant audio for critical, multi-feed live sound
andprofessionalbroadcastapplications.Witha15”overalllength,theMX415DUALincludesaflexibletopgoosenecksection
foroptimalplacement,andincludesallthemountingaccessoriesrequiredforinstallationintoalecternortabletopconfigura
tion.
Features
Wide dynamic range and frequency response for accurate sound reproduction
Dual 1 cm cardioid Microflex interchangeable cartridges
Dual 5-foot cables exiting out bottom of mic, terminating in two TQG Connectors
Two external in-line preamps
Shock mount provides over 20 dB of isolation from surface vibration noise
RF filtering with CommShield technology
®
®
®
Shure Incorporated
4/10
•
•
•
Interchangeable Cartridges
Microflex microphones use interchangeable cartridges that allow you to choose the polar pattern for different installations.
Windscreen
Snap into place when fully seated.
To remove, grip under the wider sides of the foam and gently pull.
Provides "pop" protection of 30 dB for mesh and 40 dB for foam windscreens.
Shure Incorporated
5/10
Installation
Mount the microphone using a flange or shock mount.
Shure Incorporated
6/10
1.
2.
3.
1.
2.
3.
4.
5.
1.
2.
3.
4.
Important: ThedotonthemicrophoneandTQGconnectorindicateswhichcartridgeisconnectedtowhichconnector.Thein
cluded RK100PK phantom-powered preamps converts the TQG connector to an XLR output.
A13HDB Flange:
Mark and drill 3 starter holes for the screws using the flange as a template.
Secure the flange to the mounting surface with screws.
Thread the microphone clip to the flange, then mount the microphone to the clip.
Note: Use the extension tube with the microphone clip and flange if desired.
RPM640 Flange:
Drill a 22 mm (7/8 in.) diameter hole in the mounting surface.
Mark and drill 3 starter holes for the screws using the flange as a template.
Insert the TQG connectors through the mounting flange.
Slide the retaining ring over the bottom of the gooseneck base until is flush to the bottom of the flange, then press the
ring firmly into place.
Secure the flange to the mounting surface with screws.
A400SM Shock Mount:
Drill a 44 mm (1-3/4 in.) diameter hole in the mounting surface.
Mark and drill 3 starter holes for the screws using the shock mount as a template.
Secure the shock mount to the mounting surface with screws.
Insert the TQG connectors through the hole, then insert the microphone base.
Shure Incorporated
7/10
Dimensions
Accessories
Mic Swivel Adapter A57F
Extension Tube A26X
Cast Mounting Flange A13HDB
Locking Mounting Flange RPM640
Shock Mount A400SM
Inline Preamps (2) RK100PK
Preamp Mounting Plates (2) RPM40PREMNT
Retained Foam Windscreen RK415DWS
Veraflex Windscreen A415DGWS
Storage Pouch 95E2313
Shure Incorporated
8/10
Specifications
Cartridge Type
Electret Condenser
Frequency Response
50–17000Hz
Polar Pattern
Cardioid
Output Impedance
180Ω
Output Configuration
Active Balanced
Sensitivity
@ 1 kHz, open circuit voltage
–35dBV/Pa(18mV)
Maximum SPL
1 kHz at 1% THD, 1 kΩ load
124 dB
Self Noise
A-weighted
28 dB SPL
Signal-to-Noise Ratio
Ref. 94 dB SPL at 1 kHz
66 dB
Dynamic Range
1 kΩ load, @ 1 kHz
96 dB
Common Mode Rejection
10 Hz to 100 kHz
45 dB, minimum
Clipping Level
at 1% THD
-6 dBV
Polarity
Positive sound pressure on diaphragm produces positive voltage on pin 2 relative to pin 3 of output XLR
connector
Shure Incorporated
9/10
Weight
205 g (7.23 oz)
Environmental Conditions
Operating Temperature 18–57°C(0–135°F)
Storage Temperature 29–74°C(20–165°F)
Relative Humidity 0–95%
Power Requirements
11–52VDC,2.0mA
Shure Incorporated
10/10
Certifications
Meets essential requirements of all applicable European Directives.
Eligible for CE marking.
The CE Declaration of Conformity can be obtained from Shure Incorporated or any of its European representatives. For contact
information please visit www.shure.com
The CE Declaration of Conformity can be obtained from: www.shure.com/europe/compliance
Authorized European representative:
Shure Europe GmbH
Global Compliance
Jakob-Dieffenbacher-Str. 12
75031 Eppingen, Germany
Phone: +49-7262-92 49 0
www.shure.com
Tabla de contenidos
Otros manuales de Micrófono de Shure
Shure
Shure MV88+ Manual de usuario
Shure
Shure SM137 Manual de usuario
Shure
Shure VP83F Manual de usuario
Shure
Shure UNISPHERE 565SD Manual de usuario
Shure
Shure Controlled Magnetic 444D Manual de usuario
Shure
Shure PGA 98D Manual de usuario
Shure
Shure KSM9 Manual de usuario
Shure
Shure 275SK Manual de usuario
Shure
Shure 515SBGX Manual de usuario
Shure
Shure ROSWELLITE KSM313 Manual de usuario
Shure
Shure SM35 Manual de usuario
Shure
Shure C Series Manual de usuario
Shure
Shure BETA 98/S Manual de usuario
Shure
Shure WM98 Manual de usuario
Shure
Shure BG 1.0 Manual de usuario
Shure
Shure SM86 Manual de usuario
Shure
Shure MV5 Manual de usuario
Shure
Shure CVB Manual de usuario
Shure
Shure KSM32 Manual de usuario
Shure
Shure Microflex MX418D Manual de usuario
