Shure LX Wireless System Manual de usuario

Shure Brothers Incorporated

222 Hartrey Avenue

Evanston IL 60202-3696 U.S.A.

www.shure.com

27B8654(SC)

E1999,ShureBrothersIncorporated

LX Wireless System

User Guide

LX Wireless

THANK YOU...

...for selecting the Shure LX Wireless Microphone System

This guide is intended to help you get the most out of your LX wireless microphone

system. If you have questions about your system that are not answered in this guide,

please contact Shure Customer Service at 847-866-2553, Monday through Friday,

8:00 am - 4:30 pm CST.

In Europe, please call Shure GmbH in Germany at 49-7131-72140. Other interna-

tional users please call Shure Brothers Inc. in the U.S.A. at 847-866-2200.

LX Wireless

READ ME FIRST!

To get your system up and running in just a few minutes, follow the simple in-

structions on this page. For more detailed information, refer to the sections of

this guide that apply to your system.

Receiver Connections

1. Attach the antennas to the receiver antenna connectors.

2. Connect the ac power adapter to the receiver power connector; then plug it into an

ac electrical outlet.

3. Connect the receiver audio output to the sound system, using either a low- or high-

impedance audio cable.

Transmitter Connections

1. Open the transmitter battery compartment and insert a fresh 9-volt alkaline

battery. Observe proper battery polarity ( “+/–”).

2. If you are using a body-pack transmitter, connect the microphone or WA302 instru-

ment cable to the 4-pin connector on the transmitter.

Operating the System

1. Press the receiver POWER switch. The green POWER light on the receiver will

glow.

2. SetthetransmitterPWR/OFFswitchtoPWRandtheON/MUTEswitchtoON.One

of the three lights on the transmitter will glow, indicating both that the transmitter is

on and the amount of battery life remaining. Two sets of five RF level lights on the

receiverwillalsoglowtoindicatethestrengthofthereceivedsignal.Themorelights

that glow, the stronger the signal.

3. Have someone talk or sing into the microphone, or play the musical instrument con-

nected to the transmitter. The audio level will be indicated as follows:

-Green lights (3) glowing indicates normal operation.

-Amber light glowing indicates approaching audio overload (should only occur

during loud signals).

-Red light glowing steadily indicates audio overload. If this happens, reduce the

transmittergainuntilitflickersonlyduringtheloudestsignals.RefertotheTrans-

mitter Audio Gain Adjustment section of this guide.

4. Adjust the receiver LEVEL control until the output level is compatible with the mixer

or amplifier input. In most cases, this control should be set fully clockwise.

YOU ARE NOW READY TO PERFORM!

IMPORTANT:

Every wireless microphone installation is a unique situation, and can

present a variety of problems. Never attempt a live performance without first conduct-

ing a “walkthrough” test of the system in the performing area. If major changes (addi-

tional wireless systems or intercoms, relocation of scenery, etc.) have been made

sincethe last walk–throughtest, check thewireless system again—asclose to perfor-

mance time as possible.

LX Wireless

TABLE OF CONTENTS

SYSTEM COMPONENTS 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SYSTEM FEATURES 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

LX1 BODY-PACK TRANSMITTER FEATURES, CONTROLS & INDICATORS 7. . .

LX2 HAND-HELD TRANSMITTER FEATURES, CONTROLS & INDICATORS 8. . .

LX3 RECEIVER FEATURES, CONTROLS & INDICATORS 9. . . . . . . . . . . . . . . . . . .

LX4 DIVERSITY RECEIVER FEATURES, CONTROLS & INDICATORS 10. . . . . . .

RECEIVER MOUNTING 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Single Rack Mounted Receiver 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Double Rack Mounted Receivers 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

RECEIVER CONNECTIONS 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TRANSMITTER SETUP 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

LX1 Body–Pack Transmitter Battery Installation 13. . . . . . . . . . . . . . . . . . . . . . . . .

LX2 Hand–Held Microphone–Transmitter Battery Installation 13. . . . . . . . . . . . .

Checking the Transmitter Battery 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Connecting a Lavalier Microphone or Instrument Cable to the LX1 14. . . . . . . .

Attaching the LX1 to a Belt or Guitar Strap 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installing the WA555 Grip/Switch Cover Accessory on the LX2 15. . . . . . . . . . . .

OPERATING LX1 BODY–PACK SYSTEMS 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

OPERATING THE LX2 HAND–HELD SYSTEM 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

GAIN AND SQUELCH ADJUSTMENT 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Adjusting the Transmitter Audio Gain Level 18. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Adjusting the Receiver Squelch Control 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TIPS FOR ACHIEVING OPTIMUM PERFORMANCE 19. . . . . . . . . . . . . . . . . . . . . . .

TROUBLESHOOTING 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SPECIFICATIONS 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

FURNISHED ACCESSORIES 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

OPTIONAL ACCESSORIES 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

REPLACEMENT PARTS 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

LICENSING INFORMATION 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

LX Wireless

SYSTEM COMPONENTS (FIGURE 1)

LX1

LEVEL POWER

LX4

RF A RF B AUDIO SQUELCH DIVERSITY

MARCAD

LX2

RECEIVER

RF AUDIO SQUELCH LEVEL POWER

LX3

WIRELESS

LX WIRELESS MICROPHONE SYSTEM COMPONENTS

FIGURE 1

Your LX Wireless Microphone System features a MARCADfixed frequency diver-

sity receiver operating in the VHF band between 169 and 240 MHz. Up to 12 LX wire-

less systems can be operated simultaneously in a single installation. Each LX system

contains a combination of the following items:

•One of the following transmitters:

LX1 Body-Pack Transmitter, with your choice of instrument cable or microphone,

LX2Hand-HeldMicrophone-Transmitterwithyourchoiceofinterchangeablemicro-

phone heads:

-SM58 cardioid dynamic microphone

-BETA 58supercardioid premium dynamic microphone

-SM87 supercardioid condenser microphone

-BETA 87supercardioid premium condenser microphone

•One of the following half-rack size receivers:

LX3 Receiver

LX4 Diversity Receiver

•Both single and dual rack-mounting hardware

•One antenna (LX3 systems) or two antennas (LX4 systems)

•One of the following ac power adapters: PS40,PS40E, or PS40UK.

LX Wireless

SYSTEM FEATURES

Shure LX Wireless Systems offer a number of exceptional features, including:

•Exclusive Shure MARCADCircuitry (LX4). MARCAD (MAximum Ratio Combin-

ingAudioDiversity)circuitryconstantlymonitorssignalsfrombothreceiversections

andcombinesthemtocreateasingleoutputsignal.Theresultisimprovedreception

and exceptional freedom from dropouts.

•Half-Rack Receiver Size. The LX3 and LX4 receivers interface with the HR (half-

rack) format, and are supplied with both single and dual rack-mount hardware. An

optional WA503 accessory kit lets you front-mount antennas.

•Power/Battery Fuel Gauge. The LX1 and LX2 transmitters include a three-light

gaugethatindicatesboth“poweron”andtheamountofbatteryliferemaining.(Refer

to the

Checking the Transmitter Battery

section.)

•Dual RF Level Meters (LX4). Instead of a conventional single RF meter, the LX4

receiver has two meters, one for each antenna. The dual meters indicate received

signal strength at each antenna, and make it easier to identify and troubleshoot RF

“dead spots.”

•Audio Metering. A five-light audio meter helps to optimize transmitter gain setting

and lets you monitor audio level during operation.

•True Guitar Sound. Guitar players demanding the highest degree of sound quality

and reliability will appreciate the low noise and uncolored sound of the LX Wireless

System.

•Noise Squelch. This circuit analyzes signal

quality

instead of signal

strength

. This

virtually eliminates the possibility of annoying noise bursts coming through your re-

ceiver.

•Body-Pack Transmitter Belt Clip. The belt clip has a wider contact surface for a

better grip, and firmly holds thinner, more slippery materials. It can be removed or

inverted for special positioning.

•Grip/Switch Cover Accessory. The unbreakable WA555 grip/switch cover acces-

sory,supplied with all LX2hand-held microphone-transmitters, prevents accidental

movement of the power and mute switches and provides a “grip” feel.

•Compact Power Adapter. The supplied ac power adapter incorporates small, in-

line transformers that save space on ac power strips. It also has mounting tabs so

it can be secured to any surface, as well as locking dc power connectors to prevent

accidental disconnection from the receiver.

LX Wireless

LX1 BODY-PACK TRANSMITTER

FEATURES, CONTROLS, & INDICATORS (FIGURE 2)

MUTE BAT OFF PWR

678

LX1 BODY-PACK TRANSMITTER FEATURES, CONTROLS & INDICATORS

FIGURE 2

1. Antenna. A flexible wire antenna is permanently attached to the bottom of the LX1

body-pack transmitter.

For best operation, the antenna must hang in the vertical

position, and should not be coiled or bundled.

2. BatteryCompartment.Hingedcoveronbottomsurfaceexposesthebattery.Refer

to the

Body-Pack Transmitter Battery Installation

section.

3. Audio Gain Control. Allows audio level adjustment to accommodate various

sound sources (e.g., singing, speaking, or playing an instrument). A small screw-

driver is supplied to make adjustments (see the

Setting Audio Level

section).

4. Input Jack. This is a Tini Q-Gconnector that provides connection with a variety

of lavalier and headset microphone cables, and the Shure WA302 instrument

adapter cable.

5. Power/BatteryFuelGauge.WhenthePowerswitchisturnedtothePWRposition,

oneortwoofthethreelightsonthetransmitterwillglow,indicatingpowertotheunit.

Thecoloroftheglowinglight(s)indicatestheamountofbatteryliferemaining.Refer

to the

Checking the Transmitter Battery

section.

6. Belt Clip. Allows the transmitter to be easily worn on a belt, waistband or guitar

strap.

7. MicOn/MuteSwitch.“Mutes”thetransmittertopreventunwantedsoundsfrombe-

ing picked up by the receiver

without

turning the transmitter off.

8. Power Switch. Turns transmitter power on and off.

LX Wireless

LX2 HANDHELD MICROPHONE-TRANSMITTER

FEATURES, CONTROLS, & INDICATORS (FIGURE 3)

BAT

MUTE

LX2/BETA 58

LX2 MICROPHONE–TRANSMITTER FEATURES, CONTROLS, & INDICATORS

FIGURE 3

1. Grille. Protects the microphone cartridge and helps reduce breath sounds and wind

noise. The grilles for the various microphone heads differ in appearance.

2. Power Switch. Turns transmitter power on and off.

3. Power/BatteryFuelGauge.WhenthePowerswitchisturnedtothePWRposition,

one or two of the three lights on the transmitter will glow. The color of the glowing

light(s) indicates the amount of battery life remaining. Refer to the

Checking the

Transmitter Battery

section.

4. MicOn/MuteSwitch.“Mutes”thetransmittertopreventunwantedsoundsfrombe-

ing picked up by the receiver

without

turning the transmitter off.

5. Audio Gain Control. Provides audio level adjustment to accommodate different

sound sources. Refer to the

Setting Transmitter Audio Level

section.

6. Battery Cover. Removable cup hides battery and audio gain control.

LX Wireless

LX3 RECEIVER

CONTROLS, FEATURES & INDICATORS (FIGURE 4)

WIRELESS

RECEIVER

RF AUDIOSQUELCH LEVEL POWER

ANT

OUTPUT

HI Z POWER

12.5 – 18.9 VDC

123

456

789

REAR

FRONT

LX3 RECEIVER CONTROLS, FEATURES, & INDICATORS

FIGURE 4

1. RF Presence Indicators. Glows amber when the antenna is receiving usable RF (ra-

dio frequency) signals.

2. Audio Level Indicators. Five lights glow to indicate audio signal strength. Green

lights indicate normal operation. An amber light indicates approaching overload

condition. A red light indicates excessive audio levels.

3. Squelch Control. Sets the point at which the receiver “mutes” when the transmitter

signal becomes noisy, weak or fails. This control is factory-set at the 12 o’clock position

to provide optimal operation in most applications.

4. Audio Output Level Control. Lets you adjust output level to match the input level

requirements of a mixer or amplifier. In most situations, this control should be set

fully clockwise.

5. Power On Indicator. This green light glows to indicate that the Power switch is on

and power is applied to the receiver.

6. Power On/Off Button. Turns the receiver on and off.

7. Output Connector. Quarter-inch phone jack provides unbalanced auxiliary level

(high-impedance) output.

8. Power Jack: Accepts power from the supplied ac adapter, or from any filtered 15

to 18 Vdc (400 mA minimum) supply. It will also accept the dc power cord from a

Shure WA405 Antenna Power/Distribution System.

9. Antenna Connector. UHF-type connector provides connection to the supplied

1/4-wave antenna or to coax cable used with a remote antenna. They also provide

connection to the optional Shure WA421 remote antenna cable kit used with optional

WA380 telescoping and WA490 cable-type 1/2-wave antennas.

LX Wireless

LX4 DIVERSITY RECEIVER

CONTROLS, FEATURES & INDICATORS (FIGURE 5)

12.5 – 18.9 VDC

POWER

MARCAD

DIVERSITY

RF A RF B AUDIO SQUELCH LEVEL

ANTANT OUTPUTS

HI Z BAL

MIC LINE

POWER

LX4 DIVERSITY RECEIVER CONTROLS, FEATURES, & INDICATORS

FIGURE 5

FRONT

REAR

1234567

89109118

1. Diversity Signal Indicators for A and B Antennas. These lights glow amber when

A, B, or both antennas are receiving usable RF (radio frequency) signals.

2. RF Level Indicators. Five lights per antenna glow to indicate RF signal strength.

The more lights that glow, the stronger the received signal. If none of these lights

glows, no signal is being received.

3. Audio Level Indicators. Five lights glow to indicate audio signal strength. Green

lights indicate normal operation. An amber light indicates approaching overload

condition. A red light indicates excessive audio levels.

4. Squelch Control. Sets the point at which the receiver “mutes” when the transmitter

signal becomes noisy, weak or fails. This control is factory-set at the 12 o’clock position

to provide optimal operation in most applications.

5. Audio Output Level Control. Lets you adjust output level to match the input level

requirements of a mixer or amplifier. In most situations, this control should be set

fully clockwise.

6. Power On Indicator. This green light glows to indicate that the Power switch is on

and power is applied to the receiver.

7. Power On/Off Button. Turns the receiver on and off.

8. Antenna Connectors. UHF-type connectors provide connection to the supplied

1/4-wave antennas or to coax cable used with remote antennas. They also provide

connection to the optional Shure WA421 remote antenna cable kit used with optional

WA380 telescoping and WA490 cable–type 1/2-wave antennas.

9. Output Connectors. XLR connector provides balanced low-impedance mic level

or line-level output. Quarter-inch phone jack provides unbalanced auxiliary level

(high-impedance) output.

10.Mic/Line Slide Switch: Controls output of balanced XLR connector. It can be set

for microphone (-20 dBV maximum) or line-level (+0 dBV maximum).

11.Power Jack: Accepts power from the supplied ac adapter, or from any filtered 15

to 18 Vdc (400 mA minimum) supply. It will also accept the dc power cord from a

Shure WA405 Antenna Power/Distribution System.

Otros manuales para LX Wireless System

Tabla de contenidos

Otros manuales de Sistema de micrófono de Shure

Shure

Shure MX690 Manual de usuario

Shure

Shure GLXD6 Manual de usuario

Shure

Shure MXW Manual de usuario

Shure

Shure QLXD4E P51 Manual de usuario

Shure

Shure KCX Hoja de especificaciones

Shure

Shure BLX Series Manual de usuario

Shure

Shure BLX4R Manual de usuario

Shure

Shure PGX Wireless System Manual de usuario

Shure

Shure W10BT Manual de usuario

Shure

Shure QLX-D Manual de usuario

Shure

Shure SLX-D Manual de usuario

Shure

Shure BLX288/B58 Manual técnico

Shure

Shure PSM 900 Manual de usuario

Shure

Shure SLX Wireless System Manual de usuario

Shure

Shure ULX Wireless Microphone System Manual de usuario

Shure

Shure Unf-R Manual de usuario

Shure

Shure ULX-D Manual de programación

Shure

Shure ULX-D Manual de usuario

Shure

Shure SLX Wireless System Manual de usuario

Shure

Shure U Series Manual de usuario

Shure

Shure QLX-D Series Manual de usuario

Shure

Shure BLX Wireless System Manual de usuario

Shure

Shure SLX D Series Manual de usuario

Shure

Shure SM-02 Manual de usuario

Manuales populares de Sistema de micrófono de otras marcas

Paso

Paso R824 Manual de usuario

Naxa

Naxa NAM-982 Manual de usuario

Motorola

Motorola PMNN4461 Manual de usuario

Xvive

Xvive U3 Manual de usuario

Tekon

Tekon DUOS Manual de usuario

Heyuan Intelligence

Heyuan Intelligence IOT-G2S-01 Manual de usuario

Devine

Devine WMD-IE Manual de usuario

LG LF-D7150 Manual de usuario

GE S768DAV Manual de usuario

LD U305 HBH 2 Manual de usuario

Chainway

Chainway URA8 Manual de usuario

ORATOR

ORATOR D860TD Manual de usuario

Sennheiser

Sennheiser Evolution Wireless Digital EW-DX EM 2 Manual de usuario

Alpha Technologies

Alpha Technologies RBMS Manual de usuario

SWIT Electronics Co.,LTD.

SWIT Electronics Co.,LTD. CW-S150 Manual de usuario

Panasonic

Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Manual de usuario

Pyle

Pyle PDWM5000 Manual de usuario

Airspan

Airspan AS4000 Guía