Shure BLX188CVLM17 Manual de usuario

BLX

Wireless System

Online user guide for Shure BLX wireless system.

Version: 5.1 (2022-A)

Shure Incorporated
2/24
Table of Contents
BLX   Wireless System 3
System Components 3
Quick Start Guide 3
Features 5
Front Panel 5
Back Panel 6
BLX1 6
BLX2 7
Single System Set Up 8
Setting Transmitter Group and Channel 9
Group (letter) 9
Channel (number) 9
Multiple System Setup 10
Manually Setting Receiver Group and Channel 10
Group (letter) 10
Channel (number) 10
Locking and Unlocking Controls 10
Transmitter (lock/unlock) 11
Receiver (lock/unlock) 11
Tips to Improve Wireless System Performance 11
Getting Good Sound 11
Correct Microphone Placement 12
Wearing the Headworn Microphone 12
Adjusting Gain 12
BLX1 13
BLX2 13
Batteries 13
Wearing the Bodypack Transmitter 14
Power Off 14
Removing and Installing Identification Caps 15
Troubleshooting 15
Frequency Range and Transmitter Output Level 16
Specifications 17
IMPORTANT SAFETY INSTRUCTIONS 20
Certifications 21
Important Product Information 22
LICENSING INFORMATION 22
Information to the user 23
Australia Warning for Wireless 24

Shure Incorporated

3/24

•

1. 1.

BLX 

Wireless System

System Components

Note: Your system comes with a combination of the following components.

BLX1 Bodypack Transmitter

BLX2 Handheld Transmitter (choice of SM58, BETA58A, or PG58)

BLX4 Wireless Receiver

BLX88 Dual Wireless Receiver

PS24 Power Supply

Lavalier microphone (choice of PG185, WL185 or WL93)

Headworn microphone (choice of PG30, SM31FH or SM35)

MX153 Earset microphone

Instrument microphone (BETA98H/C)

Guitar cable (WA302)

Quick Start Guide

Connect receiver to power source.

Connect receiver to mixer or amplifier. Hold power button to turn on.

Press group button on receiver to perform a group scan.

Shure Incorporated

4/24

3. 1.

Install batteries and turn on transmitter.

Onthetransmitter,setthegroupandchanneltomatchthereceiver.TheaudioLEDonthereceivershouldillu

minate.

Ifsettingupadditionalsystems,leavethefirsttransmitterandreceiveron.Foreachadditionalreceiver,manual

lysetthegrouptomatchthefirstreceiver.Note:Thereceiverwillautomaticallyperformachannelscantofind

an available frequency after the group has been selected. Set the transmitter frequency to match the receiver.

If sound is too faint or distorted, adjust the gain accordingly.

Shure Incorporated

5/24

Features

Front Panel

BLX4

BLX88

①audio LED

Indicates strength of incoming audio signal: green for normal and red for overload.

②ready LED

Green light indicates system is ready for use and receiving transmitter signal.

③LED Display

Shure Incorporated

6/24

Displays group and channel setting.

④group and channel Buttons

Scan: Push and release group button to scan for an open group and channel.

Manual: Push and hold group button to select a group. Push channel button to select a channel in the current group.

⑤power Button

Push and hold to turn power on or off.

Back Panel

BLX4

BLX88

①DC Power Jack

②Adapter Cord Tie-Off

③XLR microphone output jack (MIC out)

④6.35 mm (1/4") instrument level output jack (instrument out)

BLX1

①LED Indicator

Displays power and battery status (see Transmitter LED Indicators).

②power Switch

Toggles power on or off.

③4-Pin Microphone Input Jack (TA4 connector)

④Antenna

Shure Incorporated

7/24

⑤group Button

Changes group setting.

⑥LED Display

Displays group and channel setting.

⑦channel Button

Changes channel setting.

⑧Battery Compartment

⑨Audio Gain Adjustment

Rotate to increase or decrease transmitter gain.

BLX2

①LED Indicator

Displays power and battery status (see Transmitter LED Indicators).

②power Button

Push to turn power on or off.

③group Button

Changes group setting.

④channel Button

Changes channel and gain setting.

⑤LED Display

Displays group and channel setting.

Shure Incorporated

8/24

⑥Identification Cap

⑦Battery Compartment

Transmitter LED Indicators

LED Indicator Status

Green Ready

Rapidly Flashing Red Controls locked

Solid Red Battery power low (less than 1 hour remaining*)

Flashing Red and shuts off Batteries dead (change batteries to power on transmitter)

*For alkaline batteries only. For rechargeable batteries, solid red means the batteries are dead.

Single System Set Up

Shure Incorporated

9/24

•

Before you begin, turn off all transmitters and turn on any equipment (other microphones or personal monitoring systems) that

could cause interference during the performance.

Press and release the group button on the receiver.

The receiver scans for the clearest group and channel.

Note: If you want to stop the scan, push the group button again.

Turn on transmitter and change the group and channel to match the receiver (See SettingTransmitterGroupandChan

nel).

Once the system is set up, perform an audio check and adjust the gain if necessary.

Setting Transmitter Group and Channel

Transmitter group and channel must be manually set to match the receiver.

Group (letter)

Press and release the group button on the transmitter to activate the display. Press the groupbuttonagainandthedis

play flashes.

While the display is flashing, press the group button again to advance to the desired group setting.

Channel (number)

If channel needs to be changed, follow the same procedure using the channel button instead of the group button.

Note:

When the group and channel correctly match the receiver, the ready LED on receiver illuminates.

After manual setup, the transmitter alternately displays the group and channel setting for about two seconds.

Shure Incorporated

10/24

Multiple System Setup

Up to 12 systems can operate simultaneously (band and RF environment dependent).

Important: Set up each system one-at-a-time. Once a receiver and transmitter are tuned to the same group and channel, leave the transmitter powered on.

Otherwise, scans from the other receivers will not detect that channel as occupied. For the BLX88, be sure to setup both transmitters before progressing to the

next receiver.

Turn on any other equipment that could cause interference during the performance so it will be detected during the group and channel scans in the following

steps.

Before you begin system set up, turn all receivers ON and all transmitters OFF.

For the first receiver:

Perform a group scan.

This finds the group with the most clear channels.

Note: For the BLX88, the group scan sets up both receivers at the same time.

Turn on the first transmitter and change the group and channel to match receiver.

Leave the transmitter on and continue with the additional systems.

Note: If the selected group does not contain enough open channels, manually select group "d" when setting up larger systems.

For each additional receiver:

Use manual setup to change the receiver to match the group setting of the first receiver. Recall that each time the

group setting is changed, a channel scan is automatically done.

Turn on the transmitter and change the group and channel to match the receiver.

Leave the transmitter on and continue to the next system.

Once all receivers are set up, perform an audio check on all microphones.

Manually Setting Receiver Group and Channel

The receiver group may need to be changed as part of a multiple system setup.

Group (letter)

Hold the group button on the receiver until the display begins to flash.

While the display is flashing, press the group button again to advance to the next group.

Note: Only the group setting will be displayed during the manual setup.

Once the desired group is reached, release the group button. The receiver automatically performs a channel scan.

Channel (number)

Always use a channel selected by the channel scan. However, if necessary, the channel can be set manually. Follow the same

steps above using the channel button instead of the group button.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de micrófono de Shure

Shure

Shure LX Wireless System Manual de usuario

Shure

Shure UHF Wireless System Manual de usuario

Shure

Shure ULXD-G51 Manual de usuario

Shure

Shure Microflex Manual de usuario

Shure

Shure PA421B Manual de usuario

Shure

Shure AMS4000 Guía del usuario

Shure

Shure SLX Wireless System Manual de usuario

Shure

Shure ULX-D Manual de usuario

Shure

Shure ULX-D Manual de usuario

Shure

Shure ULXD4E K51 Manual de usuario

Shure

Shure BLX Wireless System Manual de usuario

Shure

Shure ULX Wireless Microphone System Manual de usuario

Shure

Shure QLX-D Series Manual de usuario

Shure

Shure SCM800 Manual de usuario

Shure

Shure SM-02 Manual de usuario

Shure

Shure ULXD1-V50 Manual de usuario

Shure

Shure UHF-R Wireless Manual de usuario

Shure

Shure BLX Series Manual de usuario

Shure

Shure MXW Series Manual de usuario

Shure

Shure ULX-D Manual de usuario

Shure

Shure PG Wireless Manual de usuario

Shure

Shure ULXS4 Manual de usuario

Shure

Shure Performance Gear Manual de usuario

Shure

Shure PSM 900 Guía de inicio rápido

Manuales populares de Sistema de micrófono de otras marcas

Paso

Paso R824 Manual de usuario

Naxa

Naxa NAM-982 Manual de usuario

Motorola

Motorola PMNN4461 Manual de usuario

Xvive

Xvive U3 Manual de usuario

Tekon

Tekon DUOS Manual de usuario

Heyuan Intelligence

Heyuan Intelligence IOT-G2S-01 Manual de usuario

Devine

Devine WMD-IE Manual de usuario

LG LF-D7150 Manual de usuario

GE S768DAV Manual de usuario

LD U305 HBH 2 Manual de usuario

Chainway

Chainway URA8 Manual de usuario

ORATOR

ORATOR D860TD Manual de usuario

Sennheiser

Sennheiser Evolution Wireless Digital EW-DX EM 2 Manual de usuario

Alpha Technologies

Alpha Technologies RBMS Manual de usuario

SWIT Electronics Co.,LTD.

SWIT Electronics Co.,LTD. CW-S150 Manual de usuario

Panasonic

Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Manual de usuario

Pyle

Pyle PDWM5000 Manual de usuario

Airspan

Airspan AS4000 Guía