ShowTex Autoreveal 600 Manual de usuario

SHOWTEX INSTALLATION MANUAL AUTOREVEAL 600

DISCLAIMER&COPYRIGHT

No part of this publication may be duplicated or edited in any form or

by any means, including any type of electronic or mechanical method

withoutpriorwrittenpermissionfromShowTex.

ShowTex NV and its employees are fully aware of their task to provide a reliable edition

of this document. Nevertheless they can accept no liability for (the direct or indirect

consequences of) imperfections that might remain in this edition. The material in this

manualissubjecttochangewithoutnotice.

All products from the ShowTex Rental range are supposed to be returned in the same

state as they were rented. Please treat our products with care, allowing the next user to

enjoy the products as much as you did. The rented products are internally checked

according tothe general rental conditions. Besure to checkourrental guidelines onour

websitebeforeinstallingandusing thisproduct:

http://www.showtexrental.com/showtex-rental-guidelines.

Read and understand this user manual before installing and or

operating the automatic reveal system. Failure to follow the

instructions in this document could result in serious injury!

Asa resultoftheabove warning,anyShowTex productmust beinstalled

and operated by a qualified technician who has knowledge of its

capabilities as well as its limitations.

Following the guidelines of this manual will reduce the risk of damaging the

equipmentorinjuringyourselfandthepeoplearoundyou.Damagetothe system

caused by any other method of installation than the one shown in this manual

can only be repaired or fixed at the customer s expense.

CONTENTS

Disclaimer & copyright.....................................................................................................................................3

Contents...............................................................................................................................................................3

Intro........................................................................................................................................................................4

Warranty...............................................................................................................................................................4

Product description ..........................................................................................................................................4

Safety instructions.............................................................................................................................................4

Technical specifications...................................................................................................................................5

Components...................................................................................................................................................5

Installation...........................................................................................................................................................6

How to install: setup A.................................................................................................................................7

Step 1: Removing the top & bottom covers....................................................................................7

Step 2: Adjusting the height of the roller ........................................................................................7

Step 3: Connecting the cables.............................................................................................................7

Step 4: How to operate..........................................................................................................................7

Step 5: Attaching the curtain to the roller.......................................................................................8

Step 6: Resetting the limit switches...................................................................................................8

Step 7: Setting the maximum unrolling position..........................................................................8

Step 8: Setting the maximum roll-up position...............................................................................8

Step 9: Placing the system....................................................................................................................9

Step 10: Unrolling the curtain .............................................................................................................9

Step 11: Covering the object...............................................................................................................9

Step 12: Testing the system.................................................................................................................9

How to install: setup B..............................................................................................................................10

Step 1: Removing the top cover......................................................................................................10

Step 2: Connecting the cables..........................................................................................................10

Step 3: Operating the remote control............................................................................................10

Step 4: Attaching the curtain to the roller....................................................................................10

Step 5: Resetting the limit switches................................................................................................11

Step 6: Setting the maximum unrolling position....................................................................... 11

Step 7: Setting the maximum roll-up position............................................................................11

Step 8: Replacing the top cover....................................................................................................... 11

Step 9: Placing the reveal systemin the correct position........................................................12

Step 10: Unrolling the curtain ..........................................................................................................12

Step 11: Covering up the object......................................................................................................12

Step 12: Testing the reveal system .................................................................................................12

Trouble shooting .............................................................................................................................................13

Care and maintenance...................................................................................................................................13

Contact & support...........................................................................................................................................13

SHOWTEX INSTALLATION MANUAL AUTOREVEAL 600

INTRO

Thank you for purchasing a ShowTex product.

Please take a moment to read this manual before installing or starting to use your

newrevealingsystem. Itcontainsimportantinformation regardinghealthand safety

regulations and will guide you through the installation process safely and will show

you how to use the system without injuring yourself or the people around you.

WARRANTY

ShowTex warrants that its mechanical/technical products, when delivered in new

condition,in originalpackaging,sold directlyand usedinnormal conditions, arefree

from any defects in manufacturing, materials and workmanship. The warranty shall

only apply if the mandatory preventive maintenance actions as described in the

technical documentation have been executedby skilled people. The warranty starts

onthe invoice date and expires after a period of 24 months.

Please read the entire warranty declaration on our website www.showtex.com

before installing & using this product.

PRODUCTDESCRIPTION

The Reveal 600 is perfect for big product launches, unveiling new vehicles or

premiering just about anything you can cover with an unveiling curtain. This extra-

large automaticrevealing system isoften used in combination with aSatinac curtain

that measures a surface area of 200m². With its dimensions of 17 by 12 meters, this

isthe idealsolutionfor uncovering itemsthesize ofa vanora smalltruck. The reveal

curtain is sold separately and must be attached to the revealing system before use.

Beware! The motorunitis equippedwith athermalsafety switchthat

stops the motor when overheated. Leave at least an interval of 30

minutes between the last rehearsal and the show to ensure proper

functioning.

SAFETYINSTRUCTIONS

The automatic reveal system may only beattached to lightweight fabrics.

The motor has a maximum load capacity of 18 Nm. Overloading the

The reveal curtain must unroll and roll up in the correct direction. The

curtain must follow the path of least resistance.

Guide the curtain while unrolling it to prevent the roller from blocking.

Remove any loose objects from the motor casing before activating the

system.

Make sure the reveal cloth isalways visible to the operator ofthe system.

Do not allow any item the be revealed when in doubt about the safety or

goodworkingorderofthesystem.Mostaccidentsaretheresultoflackof

training, carelessness and overconfidence, do not assume anything.

Topreventelectrocutionandinterferencewithmovingparts,disable

the power supply before carrying out any work on an automated

system.

Thesystemmust beinstalled witha correspondingearthwire ofthe same

section as the power cable.

Beware! The motion system will continue as long as the power is on. If a

problem occurs, anything in its path can cause damage to the moving

curtainuntil thelimitswitchesarereachedorthemotor unitisshutdown.

A sudden unexpected start-up of the system when the power supply to

the motor unit is not disabled, poses a risk to the operator.

The remote unit has a jump switch, do not make any changes to it.

SHOWTEX INSTALLATION MANUAL AUTOREVEAL 600

TECHNICALSPECIFICATIONS

The following components are part of the AutoReveal 600 system.

CAUTION! The components included in your shipment will depend on the specific

situation in which you want to use this system.

For more technical information please refer to the technical datasheet.

COMPONENTS

LEGEND

Weight per meter

Weight per piece

Weight per set

1. FLIGHTCASE WITH BUILT-IN MOTOR UNIT

Art. No.

Colour

Weight

Dimensions

81607400 1057

Black

52 kg/p

150x60x60cm

Power Supply

Output

RPM

Torque

230V / 50Hz / 16 A

0.435 kW

18 Nm

Duty Cycle

S2 : 4 minutes

2. REMOTE CONTROL

Art. No.

Colour

Weight

81600950 0017

Black

1.55 kg/p

3. LINK CABLE

Art. No.

Colour

Weight

Length

81600915 0257

Black

3.42 kg/p

25 m

4. POWER CABLE

Art. No.

Colour

Weight

Length

81500912 0027

Black

0.44 kg/p

2 m

5. REVEAL CURTAIN + TRANSPORTATION BAG

Fabric

Colour

Weight

Maxdimensions

Satinac

Black

110g/m²

17m L x 12m W

6. FLEXIBLE ADJUSTMENT TOOL

Colour

Blue

SHOWTEX INSTALLATION MANUAL AUTOREVEAL 600

INSTALLATION

This chapter provides all required information and steps necessary for installing a Reveal 600 system.

You can choose between 2 setups to install this product. See the pictures below to define your setup.

SETUP A: THE REVEAL SYSTEM IS PLACED UNDER THE OBJECT OR STAGE SETUP B: THE REVEAL SYSTEM IS PLACED BEHIND THE OBJECT

THE DIFFERENCE BETWEEN BOTH SETUPS IS THE ROLLING DIRECTION OF THE MOTOR AS SHOWN BY THE PICTURES BELOW.

SHOWTEX INSTALLATION MANUAL AUTOREVEAL 600

HOW TO INSTALL: SETUP A

STEP 1: REMOVING THE TOP & BOTTOM COVERS

STEP 2: ADJUSTING THE HEIGHT OF THE ROLLER

STEP 3: CONNECTING THE CABLES

STEP 4: HOW TO OPERATE

1: Loosen the butterfly locks on both sides of the flightcase.

2: Remove the top & bottom covers.

Remotecontrol:rearview

Flightcase: frontview

1: Connect the remote control and motor with the link cable.

2: Connect the remote control to a power supply.

1: Loosen the bolts on both sides of the case.

2: Lift (or lower) the roller and secure the bolts on both sides of the case.

2: Turn anticlockwise to roll up and clockwise to unroll.

1: Use the remote control to test & operate your reveal system.

out

Remotecontrol:frontview

Refer to the TDS for detailed info

abouttheminimumclearance.

230v

SHOWTEX INSTALLATION MANUAL AUTOREVEAL 600

1:Usethe switchesonthe left-handsideof themotorto installthelimit switches.

An arrow indicates the rotating direction of the roller. Make sure both switches

are set to 0.

1:Roll up the curtain, whilst keeping it well tensioned and straight.

2: Keep the curtain 0.5m out of the case, set the corresponding limit switch to 1.

STEP 5: ATTACHING THE CURTAIN TO THE ROLLER

STEP 6: RESETTING THE LIMIT SWITCHES

STEP 7: SETTING THE MAXIMUM UNROLLING POSITION

STEP 8: SETTING THE MAXIMUM ROLL-UP POSITION

1: Roll up the curtain 1.5 turn by operating the remote control.

2: Unroll 0.5 turn and set the corresponding limit switch to 1.

1: Turn the roller with hook fastener facing downwards.

2: Attach the reveal curtain to the roller using the hook & loop fastener system.

SHOWTEX INSTALLATION MANUAL AUTOREVEAL 600

1: Unroll the curtain using the remote control.

2: Keep the curtain straight and tightly tensioned during this movement.

1: Position the flightcase under the object or stage.

2: Opening facing sideways, away from the object.

1: Use the remote control to unveil your new product!

2: Make sure you leave enough time between the last rehearsal & the show.

STEP 9: PLACING THE SYSTEM

STEP 10: UNROLLING THE CURTAIN

STEP 11: COVERING THE OBJECT

STEP 12: TESTING THE SYSTEM

1: Place the revealing curtain over the object.

2: Make sure the curtain follows the path of least resistance.

SHOWTEX INSTALLATION MANUAL AUTOREVEAL 600

1: Loosen the butterfly locks on both sides of the flightcase.

2: Remove the top cover.

1: Open the front cover and turn the roller with hook fastener facing upwards.

2: Attach the reveal curtain to the roller using the hook & loop fastener system.

out

Remotecontrol:frontview

1: Connect the remote control and motor with the link cable.

2: Connect the remote control to a power supply.

230v

Remotecontrol:rearview

Flightcase: frontview

HOW TO INSTALL: SETUP B

STEP 1: REMOVING THE TOP COVER

STEP 2: CONNECTING THE CABLES

STEP 3: OPERATING THE REMOTE CONTROL

STEP 4: ATTACHING THE CURTAIN TO THE ROLLER

1: Use the remote control to test & operate your reveal system.

2: Turn clockwise to roll up and anticlockwise to unroll.

Beware!In thissetup,

out becomes

Tabla de contenidos

Otros manuales de Accesorios para proyectores de ShowTex

ShowTex

ShowTex HiSpeed Roll Up Manual de usuario

ShowTex

ShowTex widescreen 600 regular Manual de usuario

Manuales populares de Accesorios para proyectores de otras marcas

Optoma

Optoma BX-AL133B Manual de usuario

PEERLESS

PEERLESS PE 1120 Guía

Osram

Osram SIRIUS HRI Series Manual

Presentation Switchers

Presentation Switchers PS111 Manual de usuario

Kramer

Kramer VIA GO Manual de usuario

Yamaha

Yamaha PJL-112 Manual de lista de piezas

Swedstyle

Swedstyle CL23AA02ZA25E Manual de usuario

Mitsubishi Electric

Mitsubishi Electric 236CB Manual del propietario

Epson

Epson BrightLink 475Wi Manual de usuario

Acer

Acer WP100 Manual de usuario

i3 i3board Manual de usuario

CHIEF

CHIEF HB-43E Manual de usuario

Biamp

Biamp Modena Hub Manual de servicio

NEC

NEC MP10RX Manual de usuario

Panamorph

Panamorph DCR-S3 Manual de usuario

Exact solutions

Exact solutions FRAME-EVO-P10 Manual de usuario

CHIEF

CHIEF VCM103S Manual de usuario

InFocus

InFocus LP70+ Guía

ShowTex autoreveal 600 Manual de usuario

Manuales populares de Accesorios para proyectores de otras marcas