ShoreStation SSV40108HS Manual de usuario

Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorestation.com 0004205

Page 1 of 22 Rev 2.7 3/13/2018

Assembly Instructions

Hydraulic Boat Lift

SSV40108HS & HSDW, SSV40120HS & HSDW, SSV50120HS,

SSPV50132LHS, SSPV60120LHS, & SSV60120HS & HSDW,

SSV60132HS, SSV80132HSDW, SSV100132HSDW &

SSPV100144HSDW, SSV100144HSDW, & SSV150144HSDW

Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorestation.com 0004205

Page 2 of 22 Rev 2.7 3/13/2018

Step #1 –Sort Hardware

Open the hardware box and bag and sort the hardware and other contents by size. Locate the

fastener finder sheet in the hardware box to help identify the fasteners used in the assembly of

these lifts.

Step #2 –Assemble Base Pads

Collect enough of the fasteners and items shown below to assemble four base pads. Align the

channel clamp with the holes in the base pad as shown, insert bolts from the bottom up and

secure with lock nuts. Tighten and repeat for all four base pads.

Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorestation.com 0004205

Page 3 of 22 Rev 2.7 3/13/2018

Step #3 –Assemble Base Pads to Legs

Locate the leg bundle or bundles and cut the bands to open it up. Locate bolts and nuts in the

pre-packaged bag and slide the bolt thru the channel clamp and the adjustable leg tube as

shown and secure with a brass locknut with nylon insert.

Note that the bolts (1/2-13 X 4 1/2” HC Stainless and Brass lock nut with nylon insert) should

be inserted in the same direction as that of the u-bolt. Repeat this process on the remaining

legs.

Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorestation.com 0004205

Page 4 of 22 Rev 2.7 3/13/2018

Step #4 –Assembly of Lower Side Frame

Using the chart at the bottom of the page find the model that you are assembling, locate the

necessary components that are included in the lower frame bundle. Your assembly will start by

laying two legs down with the corner blocks as shown and using the chart slide a sideframe

tube over the corner block and insert the short bolt (see chart) with a 3/8” flat washer into the

hole closest to the post assembly. Secure with flat washer and brass locknut. DO NOT

TIGHTEN.

Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorestation.com 0004205

Page 5 of 22 Rev 2.7 3/13/2018

LOWER FRAME SSPV60120LHS

Front & Rear

Crossmembers

Side frames Short Bolts

Long Bolts

SSV40108HS &

HSDW

5" X 2" X 107" 5" X 2" X 131" 3/8-16 X 6" 3/8-16 X 6 1/2"

SSV40120HS &

HSDW, SSV50120HS

5" X 2" X 119" 5" X 2" X 131" 3/8-16 X 6" 3/8-16 X 6 1/2"

SSPV50132LHS 5" X 2" X 131" 5" X 2" X 167" 3/8-16 X 6" 3/8-16 X 6 1/2"

SSPV60120LHS 6" X 2" X 119" 6" X 2" X 167" 3/8-16 X 7" 3/8-16 X 7 1/2"

SSV60120HS &

HSDW

6" X 2" X 119" 6" X 2" X 143" 3/8-16 X 7" 3/8-16 X 7 1/2"

SSV60132HS 6" X 2" X 131" 6" X 2" X 143" 3/8-16 X7" 3/8-16 X 7 1/2"

SSV80132HSDW 6" X 2" X 131" 6" X 2" X 155" 3/8-16 X 7" 3/8-16 X 7 1/2"

SSV10132HSDW 6" X 2" X 131" 6" X 2" X 155" 3/8-16 X 7" 3/8-16 X 7 1/2"

SSPV100144HSDW 8" X 2" X 143" 8" X 2" X 155" 3/8-16 X 8 1/2" 3/8-16 X 9"

SSV150144HSDW 8" X 2" X 143" 8" X 2" X 185" 3/8-16 X 8 1/2" 3/8-16 X 9"

Lower Frame Components

Bolts to Assemble

Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorestation.com 0004205

Page 6 of 22 Rev 2.7 3/13/2018

Step #5 –Attach Front & Rear Frame Crossmembers

Using the chart, locate the correct length tubes for crossmembers. With the unit still laying on

it’s side, slide the crossmembers over the other corner block leg and insert the short bolt with a

washer into the hole closest to the post and secure on the bottom with a flat washer and brass

lock nut. DO NOT TIGHTEN.

Step #6 –Complete Frame Corner Assembly

Flip the entire assembly upright onto the base pads.

Locate the long bolts and the bottom corner cable bracket. Insert the long bolt with a flat

washer thru the second hole from the post, thru the frame tubes and then thru the corner cable

bracket on the bottom as shown. Secure with a flat washer and brass lock nut. Do not tighten.

Note: The leg bundle for the

SSV150144HSDW has stops welded to

the leg tubes and should be used at this

time.

Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorestation.com 0004205

Page 7 of 22 Rev 2.7 3/13/2018

Step #7 –Complete Bottom Frame & Post Assembly

Insert the corner blocks of the two remaining leg assemblies into the crossmembers as shown

below, insert short bolts with washers in the holes closest to the posts to keep them in place.

Pull the legs apart slightly and slide the other side frame over the corner blocks and secure

these also with short bolts, washers, and brass lock nuts. Square the frame and tighten all

hardware installed.

Properly Securing a Lift’s Lower Frame

Tighten all fasteners with an air or battery powered high torque impact wrench. It’s important

to tighten the fasteners so the platform tube pulls tight to the corner block. The fastener needs

to slightly crease the tube wall until there is no gap between the tube and the corner block. In

some instances the impact wrench may not have enough torque and it may be necessary to

hand tighten in order to achieve contact with the corner block.

Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorestation.com 0004205

Page 8 of 22 Rev 2.7 3/13/2018

Step #8A –Assemble the Lift Platform for 4000#, 5000#, and 6000#

Lay the V-Shaped cradle tubes across the lower frame as shown (4000, 5000, and 6000lb).

Place the end with the lift cable threaded out the bottom on the same side as the corner cable

brackets.

For the 4000, 5000, and 6000 lb. models insert a carriage bolt into the corner guide as shown

and slide the head into the top slot in the cradle tube. Secure corner guide with a flat washer

and lock nut. Do the same on the other three corners. Slide two carriage bolts into the top slot

Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorestation.com 0004205

Page 9 of 22 Rev 2.7 3/13/2018

and 2 into the bottom slot on the inside of the cradle tube. Using those bolts, mount a pair of

side rail brackets on each end of the cradle tube as shown above. Position the outer edge of

the brackets at least 3 inches from the end of the cradle tube. It is important to keep this

distance equal on all four corners to keep it square. Do not tighten at this time.

Insert the platform rails into the space between the mounting brackets and between the v-

frames and secure with bolts, washers and nuts as shown.

Step #8B –Assemble the Lift Platform for 8000# - 15000#

The cradle tubes on all the lifts above 8000# have galvanized steel cradle tubes with different

attaching system. They also use the plastic (plastic and aluminum) ring style corner guides.

Lay the galvanized cradle tubes on the bottom frame with the end with the cables coming out

the bottom on the same side as the corner cable brackets. Slide the corner guides over the

post and attach as shown.

Place the platform side rails between the welded brackets on the cradle tube and attach as

illustrated above (use the same fasteners as used for the aluminum cradle tube on the 4000# -

6000# lifts illustrated above).

Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorestation.com 0004205

Page 10 of 22 Rev 2.7 3/13/2018

The following picture shows the position of the level cable as it comes over the pulley in the

cradle tube and out the bottom to go to the cable mounting bar attached to the corner of the

lower frame. Note the other two holes on the end of the cradle tube. These will be used later to

attach the cables coming from the bottom of the lift tube.

Step #9 –Attach the Level Cable

Attach the level cable as shown inserting the cable into the hole closest to the sideframe and

securing with a flat washer and 2 brass hex nuts (see chart on page 12 for hardware sizes).

The first nut will be run to the bottom of the threads and the second run down and secured

tightly against the first. Repeat on other level cable.

Este manual sirve para los siguientes modelos

Otros manuales de Sistema de elevación de ShoreStation

ShoreStation

ShoreStation SSV60108MS Manual de usuario

ShoreStation

ShoreStation SSV30120EAS Manual de usuario

ShoreStation

ShoreStation FlexPower SSV40108EDS Manual de usuario

ShoreStation

ShoreStation SSV30120EAC Manual de usuario

ShoreStation

ShoreStation SS1053DE Manual de usuario

ShoreStation

ShoreStation FlexPower SSV30108EDS Manual de usuario

ShoreStation

ShoreStation Manual SSV50108MS Manual de usuario

ShoreStation

ShoreStation SSV40108HAC Manual de usuario

ShoreStation

ShoreStation SSV20100EDC Manual de usuario

ShoreStation

ShoreStation SSV30108EAC Manual de usuario

ShoreStation

ShoreStation FlexPower SSV40120EDS Manual de usuario

ShoreStation

ShoreStation FlexPower SSV30120EDS Manual de usuario

ShoreStation

ShoreStation Manual SSV20100MS Manual de usuario

ShoreStation

ShoreStation SSV15100EDC Manual de usuario

ShoreStation

ShoreStation SS1053 Manual de usuario

ShoreStation

ShoreStation SSV40120EAC Manual de usuario

ShoreStation

ShoreStation WATERFRONT SYSTEMS Manual de usuario

ShoreStation

ShoreStation SSV20100EAC Manual de usuario

ShoreStation

ShoreStation SSV60120EDC Manual de usuario

ShoreStation

ShoreStation SSV60108EAC Manual de usuario

ShoreStation

ShoreStation SS1564M Manual de usuario

ShoreStation

ShoreStation SSV30108 Manual de usuario

ShoreStation

ShoreStation Manual SSV50108MS Manual de usuario

ShoreStation

ShoreStation SSV40108EDC Manual de usuario

Manuales populares de Sistema de elevación de otras marcas

morse

morse 82H-124 Manual de usuario

Braun

Braun NL955 Series Manual de usuario

haacon

haacon 1889.10 Manual de usuario

Protekt

Protekt AT 252 Manual de usuario

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manual de usuario

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manual de usuario

Genie

Genie Z-60/34 Manual de usuario

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manual de usuario

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manual de usuario

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manual de programación

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manual de programación

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manual de programación

BERG

BERG BeNomic EasyLeaf Manual de usuario

Powermate

Powermate LiftGate LG-3 Manual de usuario

Snorkel

Snorkel TM12 Series Manual de usuario

Terberg

Terberg OMNIDEKA Manual de usuario

Harmar Mobility

Harmar Mobility AL625 Instrucciones de funcionamiento

Rotary

Rotary SPO16 Manual de usuario