Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003724
REV D 12/09/2010
SBA017-15 ShoreBridge Assembly Instructions
• Breakthebundlesandsortallitemsbysize.
• LocatetheShoreBridgemountingbracketusedtoattach
thedockladdermountingbrackettothedockframe.
• Mountbracket tothe longuprights inthe side,this will
not mount to the center upright, using 3/8 X 2 & 7/16 X 3
square u-bolts and securing with stainless steel at washers
andbrasslocknutswithnyloninserts.
•Locatethedockladdermountingbracketweldment.
• Orientate the two parts as shown in the drawing. Note
thatthemountingbracketswillpositiontheladdersoitwillsetat
ananglewhenpositonedcorrectly.
• Align the holes in the two weldments as shown.Attach
thetwoweldmentstogetherbyplacingfour(4)3/8”x3/4”car-
riageboltsinthealignedholes.Notetheheadsoftheboltsmust
beplacedasshownsothesquareportionofthecarriagebolt
mateswiththesquareholespunchedinthedockladdermount-
ingbracket.
• Securewithfour(4)3/8”lockwashersandhexnuts.Tight-
en.
Installation Instructions
• Notethattherungsoftheladderarespacedsothatone
rungoftheladderwillslideoverthetopsquaremountingtube
while the rung below will slip over the next square tube. This
allowstheladdertobeadjustedupordownwithrespecttothe
waterlevel.
• Placetheladderrungsontothesquaretubesofthedock
laddermountingbracket.Pressthespringloadedretainerpins
locatedinthetopsquaretubesotheladderwillslidecompletely
overthetubes.Whenfullydownonthesquaretubes,thespring
pinswillsnapintotheholesprovidedintheladderrunglocking
itinthisposition.
• Toadjusttheheightoftheladderortoremovetheladder,
simplypressthespringloadedpinsinandraiseuponthelad-
der.Repositiontonewlocation.
• Assemblyandinstallationarecomplete.
DA0041-15 Floating Dock Assembly Instructions
• Breakthebundlesandsortallitemsbysize.
• Locatetheoatingdockconnectorweldmentandthedocklad-
dermountingbracket.Seepartsdiagram.
• Aligntheholesinthetwoweldmentsasshown.Attachthetwo
weldmentstogetherbyplacingfour(4)3/8”x3/4”carriagebolts
inthealignedholes.Notetheheadsoftheboltsmustbeplaced
asshownsothesquareportionofthecarriageboltmateswith
thesquareholespunchedinthedockladdermountingbracket.
• Securewithfour(4)3/8”lockwashersandhexnuts.Tighten.
Installation Instructions
• Selecttheposition ontheoatingdock thattheladderwill be
mounted.
• Removethe3/8”x2”hexboltassemblyfromthetopsideofthe
oatingdockconnectorweldment.
• Insert the oating dock connector weldment into the selected
notchmoldedinthesideoftheoatingdocksection.Raisethe
unitup.Secureinplaceusingtheboltassemblyjustremovedin
thepreviousstep.Tighten.
• Notethattherungsoftheladderarespacedsothatonerung
oftheladderwillslideoverthetopsquaremountingtubewhile
therungbelowwillslipoverthenextsquaretube.Thisallows
theladdertobeadjustedupordownwithrespecttothewater
level.
• Placetheladderrungsontothesquaretubesofthedockladder
mountingbracket.Pressthespringloadedretainerpinslocated
inthetopsquaretubesotheladderwillslidecompletelyover
thetubes.Whenfullydownonthesquaretubes,thespringpins
willsnapintotheholesprovidedintheladderrunglockingitin
thisposition.
• Toadjusttheheightoftheladderortoremovetheladder,simply
pressthespringloadedpinsinandraiseupontheladder.Re-
positiontonewlocation.
• Assemblyandinstallationarecomplete.
