Shop-Vac SSP14 SERIES Manual de usuario

USER MANUAL

Series:

SSP14

SSP16

ATTENTION!

DANGER!

Read all safety rules carefully before attempting to operate. Retain for

future reference.

Never operate this unit when ﬂammable materials or

vapors are present because electrical devices produce

arcs or sparks that can cause a ﬁre or explosion. NEVER

OPERATE UNATTENDED!

For your records, please record the following information

and store this user manual in a safe location.

Catalog No.

Model No.

Purchase Date:

(Located on the carton)

(Located on top portion of the vacuum)

87552-83

Household and Workshop use

WET/DRY VACUUM

TABLE OF CONTENTS

Important Safety Instructions .............................................................................................

Grounding Instructions....................................................................................................

Extension Cords.................................................................................................................

Unpacking .........................................................................................................................

Assembly.......................................................................................................................

Vacuum Set Up and Operation ...........................................................................................

Filter Installation and Maintenance..................................................................................

Pump Set Up and Operations ........................................................................................

Blower Feature ................................................................................................................

Empty Liquid Waste From the Tank ..................................................................................

Automatic Suction Shut Off...............................................................................................

Lubrication .......................................................................................................................

Storage............................................................................................................................

Service ............................................................................................................................

Troubleshooting ...............................................................................................................

Warranty and Contact Information.....................................................................................

3-4

5-6

6-9

9-10

SECTION PAGES

TOOLS NEEDED

PAGE 2

• Safety Glasses • Flathead Screwdriver

IMPORTANT SAFETY INSTRUCTIONS

When using an electric appliance, basic precautions should always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE.

WARNING –TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:

1. Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing.

Connect to a properly grounded outlet only. See Grounding Instructions.

2. Do not expose to rain – store indoors.

3. Do not allow to be used as a toy. Close attention is necessary when used by or near children.

4. Use only as described in this manual. Use only Manufacturer’s recommended attachments.

5. Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped,

damaged, left outdoors or dropped into water, contact Shop-Vac Corporation for assistance.

6. Do Not: pull or carry by cord, use cord as a handle, close a door on cord or pull cord around sharp edges

or corners. Do not run appliance over cord. Keep cord away from heated surfaces.

7. Do not unplug by pulling on cord. To unplug, grasp the plug; not the cord.

8. Do not handle plug or appliance with wet hands.

9. Do not put any object into openings. Do not use with any openings blocked; keep free of dust, lint, hair

and anything that may reduce air ﬂow.

10. Keep hair, loose clothing, ﬁngers and all parts of body away from openings and moving parts.

11. Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes.

12. Do not use without dust bag and/or ﬁlters in place.

13. Turn off all controls before unplugging.

14. Use extra care when cleaning on stairs.

15. Do not use to pick up ﬂammable or combustible liquids such as gasoline or use in areas where they

may be present.

16. Do not use your cleaner as a sprayer of ﬂammable liquids such as oil base paints, lacquers, household

cleaners, etc.

17. Do not vacuum toxic, carcinogenic, combustible or other hazardous materials such as asbestos, arsenic,

barium, beryllium, lead, pesticides or other health endangering materials. Specially designed units are

available for these purposes.

18. Do not pick up soot, cement, plaster or drywall dust without cartridge ﬁlter and collection ﬁlter bag in

place. These are very ﬁne particles that may pass through the foam and affect the performance of the

motor or be exhausted back into the air. Additional collection ﬁlter bags are available.

19. Do not leave the cord lying on the ﬂoor once you have ﬁnished the cleaning job. It can become a tripping

hazard.

20. Use special care when emptying heavily loaded tanks.

21. To avoid spontaneous combustion, empty tank after each use.

22. The operation of a utility vac can result in foreign objects being blown into eyes, which can result in eye

damage. Always wear safety goggles when operating vacuum.

23. STAY ALERT. Watch what you are doing and use common sense. Do not use vacuum cleaner when you

are tired, distracted or under the inﬂuence of drugs, alcohol or medication causing diminished control.

24. WARNING! Do NOT use this vacuum cleaner to vacuum lead paint debris because this may disperse ﬁne

lead particles into the air. This vacuum cleaner is not intended for use under EPA Regulation 40 CFR Part

745 for lead paint material cleanup.

SAVE THESE INSTRUCTIONS

WARNING –DO NOT LEAVE VACUUM UNATTENDED

WHEN IT IS PLUGGED IN AND/OR OPERATING. UNPLUG UNIT WHEN NOT IN

USE.

GROUNDING INSTRUCTIONS

This appliance must be grounded. If it should malfunction or breakdown, grounding provides a path of

least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with

a cord having an equipment-grounding conductor and grounding plug. The plug must be inserted into an

appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

PAGE 3

GROUNDING INSTRUCTIONS (CONT’D.)

WARNING –IMPROPER CONNECTION OF THE EQUIPMENT-GROUNDING

CONDUCTOR CAN RESULT IN A RISK OF ELECTRIC SHOCK. CHECK WITH A QUALIFIED

ELECTRICIAN OR SERVICE PERSON IF YOU ARE IN DOUBT AS TO WHETHER THE OUTLET IS

PROPERLY GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE APPLIANCE – IF

IT WILL NOT FIT THE OUTLET, HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED

ELECTRICIAN.

This appliance is for use on a nominal 120-volt circuit, and has a grounded plug that looks like the plug

illustrated in sketch A. A temporary adaptor that looks like the adaptor illustrated in sketches B and C may

be used to connect this plug to a 2-pole receptacle as shown in sketch B if a properly grounded outlet is

not available. The temporary adaptor should be used only until a properly grounded outlet (sketch A) can

be installed by a qualiﬁed electrician. The green colored rigid ear, lug or the like extending from the adaptor

must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the

adaptor is used, it must be held in place by a metal screw.

IN CANADA, THE USE OF A TEMPORARY ADAPTOR IS NOT PERMITTED BY THE CANADIAN ELECTRICAL

CODE. Make sure that the appliance is connected to an outlet having the same conﬁguration as the plug. No

adaptor should be used with this appliance.

EXTENSION CORDS

When using the appliance at a distance where an extension cord becomes necessary, a

3-conductor grounding cord of adequate size must be used for safety, and to prevent loss

of power and overheating. Use Table A to determine A.W.G. wire size required. To determine

ampere rating of your vacuum, refer to nameplate located on motor housing. Before using

appliance, inspect power cord for loose or exposed wires and damaged insulation. Make any needed repairs

or replacements before using your appliance. Use only three-wire outdoor extension cords which have

three prong grounding-type plugs and three-pole receptacles which accept the extension cord’s plug. When

vacuuming liquids, be sure the extension cord connection does not come in contact with the liquid.

NOTE: STATIC SHOCKS ARE COMMON IN DRY AREAS OR WHEN THE RELATIVE HUMIDITY OF THE AIR IS

LOW. THIS IS ONLY TEMPORARY AND DOES NOT AFFECT THE USE OF THE APPLIANCE. TO REDUCE THE

FREQUENCY OF STATIC SHOCKS IN YOUR HOME, THE BEST REMEDY IS TO ADD MOISTURE TO THE AIR WITH

A CONSOLE OR INSTALLED HUMIDIFIER.

UNPACKING

Pull lid latches in an outward motion, remove tank cover and any accessories that may have been shipped

in the tank. Refer to the assembly section before replacing the tank cover.

Volts Total length of cord in feet

120V

Ampere Rating

More Not More

Than Than

0 - 6

6 - 10

10 - 12

12 - 16

25 50 100 150

AWG

Not recommended

TABLE A

PAGE 4

SKETCH A SKETCH B SKETCH C

GROUNDING METHODS

PAGE 5

ASSEMBLY

CASTER SYSTEM

PLASTIC TANK WITH CASTER FEET

You will ﬁnd four caster feet, four casters and four screws with your vacuum. Assemble as

follows:

1. With cord disconnected from receptacle and tank cover removed, turn tank upside down

so that bottom is facing up.

2. With front of tank facing you, take caster feet marked with the

letter A and place in slots on left front and right rear of tank

also marked with the letter A. Secure with screws provided.

3. Take caster feet marked with the letter B and place in slots on right front and

left rear of tank also marked with the letter B. Secure with screws provided.

4. If ﬂat washers are included in hardware package place ﬂat washer over stem of caster before installing

casters into feet. NOTE: Flat washers are not required with all units.

5. Insert casters into feet by placing stem of caster into holes provided. Apply

pressure and twisting motion until casters snap into place. Return tank to

upright position.

TOOL HOLDER

(Not standard with all models)

If your unit came with a tool holder, follow these instructions to install it.

1. If your tool holder looks like the one shown to the right, assemble as follows:

a. Set tank cover onto the tank. Position with back of tank cover facing you.

b. Take tool holder and place tabs on tool holder into slots on back of

tank cover.

c. Press down until tabs snap into place. Continue to step 3.

Caster

Foot

Screw

Caster

Foot

Screw

Caster

Foot

ASSEMBLY (CONT’D.)

2. If your tool holder looks like the one shown to the right, assemble as follows:

a. Set tank cover onto the tank. Position back of tank facing you.

b. Take tool holder and slide over notches located on rear of tank. Continue to step 3.

3. Remove tank cover from tank and refer to the set up and operation section.

VACUUM SET UP AND OPERATION

DANGER –This equipment incorporates parts such as switches, motors or the

like that tend to produce arcs or sparks that can cause an explosion. Do not pick up ﬂammable,

combustible, or hot materials. Do not use around explosive liquids or vapors, as electrical devices

produce arcs or sparks which can cause a ﬁre or explosion - do not use at ﬁlling stations or

anywhere gasoline is stored or dispensed.

1. Refer to the ﬁlter installation and maintenance section to make sure the correct ﬁlters are installed for

normal dry or wet pick up operation based on your cleaning needs. To use the pump feature, refer to the

pump set up and operation section.

2. Replace tank cover and apply pressure with thumb to each latch until it snaps tightly into place. Make

sure each latch is clamped securely.

3. Insert machine hose end with locking-nut into inlet located on the front of the

tank. Turn locking nut to tighten. Do not over-tighten.

4. Attach the desired cleaning accessory onto the accessory end of the hose. NOTE: Many more useful tools

are available at your local dealer or the Shop-Vac®website.

5. Plug the cord into the wall outlet. Your cleaner is ready for use.

I = ON, O = OFF

FILTER INSTALLATION AND MAINTENANCE

FILTRATION SYSTEM

There are a variety of ﬁlters available for your vacuum. There are cage ﬁlters that install onto the underside

of the tank cover and tank ﬁlters that install into the tank. The ﬁlters are grouped into three ﬁltration

categories. General ﬁltration is used for large debris; such as, wood chips, nails and gravel. Medium

ﬁltration is used for medium debris; such as, dirt, sand and sawdust. Fine ﬁltration is used for ﬁne debris;

such as drywall dust, cold ash and cement dust. It is important to have the correct ﬁlters installed for your

cleaning operation to protect your vacuum motor. THE MOST EFFICIENT FILTRATION FOR YOUR VACUUM IS A

FINE FILTRATION CAGE FILTER WITH A FINE FILTRATION TANK FILTER.

NOTE: When using the vacuum to pick up very ﬁne dust. It will be necessary to empty the tank and clean

the cage ﬁlter at more frequent intervals to maintain maximum pick up power or add a disposable ﬁlter bag.

DRY PICK UP OPERATION

NOTE: Never use the vacuum for dry pick up without a dry use ﬁlter installed. Using the vacuum without a

ﬁlter will cause dust to discharge from the blower port and cause damage to the motor.

WARNING –ALWAYS DISCONNECT THE PLUG FROM THE WALL OUTLET

BEFORE REMOVING THE TANK COVER.

PAGE 6

PAGE 7

FILTER INSTALLATION AND

MAINTENANCE (CONT’D.)

Follow the instructions for the ﬁlter that came with your vacuum. Some ﬁlters mentioned do not come

standard with all vacuums. Additional ﬁlters are available at your local dealer or the Shop-Vac®website.

CARTRIDGE FILTER

The cartridge ﬁlter can be used for dry pick up and small quantities of wet pick up. Installation is the same

for both. When picking up ﬁne dust or powders a high efﬁciency ﬁlter bag must be used with the cartridge

ﬁlter.

1. If a foam sleeve is installed on the lid cage, remove it by sliding it off the lid cage.

NOTE: If the cartridge ﬁlter has been used for wet pick up, it must be cleaned and

dried before using it for dry pick up.

2. With the tank cover in an upside down position, slide the cartridge down over the

lid cage, pushing until the ﬁlter seals against the cover.

3. Place the ﬁlter retainer into the top of the cartridge ﬁlter. Hold the tank cover with

one hand, turn the handle on the ﬁlter retainer clockwise to lock the ﬁlter into

place.

4. To remove the ﬁlter for cleaning, hold the tank cover and turn the ﬁlter retainer

counter-clockwise to loosen and remove.

5. Slide the cartridge ﬁlter off the lid cage.

6. Clean the ﬁlter by shaking or gently brushing off excess dirt. Extremely dirty ﬁlters may be cleaned with

water by rinsing from the inside of the ﬁlter. Dry completely (approximately 24 hours).

7. Check the ﬁlter for tears or small holes. If none are found, reinstall the ﬁlter. To prevent damage to your

vacuum, do not use a ﬁlter with a hole or tear.

NOTICE –This ﬁlter is made of high quality paper designed to stop small

particles of dust. The ﬁlter can be used for wet or dry pick up. A dry ﬁlter is necessary to

pick up dry material. If you use your vac to pick up dust when the ﬁlter is wet, the ﬁlter

will clog quickly and be very difﬁcult to clean. The ﬁlter may become saturated when

picking up large quantities of liquid causing misting to appear in the exhaust air. At this

time, you should dry or change the ﬁlter to eliminate this occurrence. Please handle the

ﬁlter carefully when removing it for cleaning or when installing it. Check the ﬁlter for tears

or small holes. Even a small hole can cause dust to be exhausted. Do not use a ﬁlter with

holes or tears. Replace it immediately.

PAGE 8

FILTER INSTALLATION AND

MAINTENANCE (CONT’D.)

WARNING –KEEP FILTERS CLEAN. EFFICIENCY OF THE VACUUM IS LARGELY

DEPENDENT ON THE FILTER. A CLOGGED FILTER CAN CAUSE OVERHEATING AND POSSIBLY

DAMAGE THE CLEANER. CHECK THE FILTER PERIODICALLY AND REPLACE AS REQUIRED.

DISPOSABLE FILTER BAG

Use the disposable ﬁlter bag in conjunction with the cartridge ﬁlter for easy disposal of the debris. The bag

is not required for normal dry pick up. When picking up ﬁne dust or powders a high efﬁciency ﬁlter bag

must be used. NOTE: For dry use only.

1. Make sure the cord is disconnected from the receptacle, tank cover is removed and the hose is

disconnected from tank inlet.

2. Remove inlet deﬂector from deﬂector guide. NOTE: Hose must be removed before

inlet deﬂector can be taken out.

3. With the opening of the inlet deﬂector facing the left or right side of the ﬁlter bag,

slide ﬁlter bag collar over deﬂector matching notches of bag collar to tabs on inlet

deﬂector. Bag will only ﬁt properly one way.

4. Slide deﬂector with ﬁlter bag attached into deﬂector guide.

5. Reinsert hose into inlet and tighten locking-nut. When secured in place expand bag and position around

inside of tank.

6. NOTE: When removing ﬁlter bag from tank, remove inlet deﬂector from ﬁlter bag collar and reinstall into

deﬂector guide. Inlet deﬂector should always be in place for any type of cleaning.

WARNING –FOR FINE DUST AND POWDERS.

When vacuuming ﬁne dust, or powders of any kind (plaster, drywall dust, cold ashes, concrete dust, etc.)

a high efﬁciency drywall ﬁlter bag must be used. When vacuuming normal household dust and debris,

standard household disposable ﬁlter bags may be used.

WET PICK UP OPERATION

1. Your vacuum can be used for wet pick up. Remove ALL dirt and debris found in the tank. Remove all dry

use ﬁlters, including the ﬁlter bag, from the vacuum. NOTE: To use the pump feature, refer to the pump

set up and operation section.

2. A clean cartridge ﬁlter may be used to pick up small quantities of liquid. To use the cartridge ﬁlter; follow

the instructions under dry pick up.

3. For vacuuming large quantities of liquid use a foam sleeve. If a foam sleeve did not come standard with

your unit, one may be purchased at your local dealer, the Shop-Vac®website or by contacting Shop-Vac®

customer service. To use the foam sleeve; follow the instructions in this section.

4. Misting in the exhaust air or dripping of liquid around the tank cover may occur if the ﬁlter becomes

saturated during wet pick up. If this occurs, remove the ﬁlter and allow to dry, or replace with another

dry ﬁlter.

5. Turn the unit off immediately upon completing a wet pick up job or when tank is full and ready to be

emptied. When the tank is full, suction will drastically reduce.

PAGE 9

FILTER INSTALLATION AND

MAINTENANCE (CONT’D.)

Refer to the automatic suction shut off section for more information. Raise the hose to drain any excess

liquid into the tank. Follow the instructions in the emptying liquid waste section.

6. Before storing the vacuum cleaner or using for dry pick up, clean and dry the interior of the tank and the

underside of the tank cover. Clean and allow the ﬁlters to dry completely.

7. Wet pick up accessories should be washed periodically; especially after picking up wet, sticky kitchen

accidents. This can be accomplished with a warm solution of soap and water.

FOAM SLEEVE

1. With the tank cover in an upside down position, slide the foam sleeve down over the lid cage, pulling

until foam sleeve completely covers the lid cage.

2. To clean the foam sleeve, side it up and off the lid cage. Shake excess debris off

of the foam sleeve with a rapid up and down movement.

3. Hold foam sleeve under running water for a couple minutes, rinsing from the inside of the ﬁlter. A water

wash is not always required, depending on the condition of the ﬁlter.

4. Check the ﬁlter for tears. If any are found, replace with a new ﬁlter.

PUMP SET UP AND OPERATION

WARNING –TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT DIRECT

DISCHARGE STREAM AT UNIT!

WARNING –THE CARTRIDGE FILTER IS NOT COMPATIBLE WHEN UTILIZING

THE PUMP PICK UP ASSEMBLY.

NOTE: Not for use as a sump pump. Do not leave unit unattended while in use.

SET UP

1. The pump feature allows you to vacuum large amounts of liquid without having to manually empty

heavy tanks of liquid. Always disconnect the plug from the wall receptacle before removing the tank

cover. Remove the tank cover.

2. Remove any ﬁlters, other than foam sleeve, installed on the vacuum. If not already done, install foam

sleeve. Refer to the ﬁlter installation and maintenance section for installation instructions.

3. Remove ALL dirt and debris found in tank.

4. Insert tube into pick up cage and push until tube comes to a stop.

5. Take pick up assembly from step 4 and insert tube into hole in bottom of lid cage

and push until assembly comes to a stop. NOTE: Do not attempt to pump without

pick up cage in place or screen on pick up cage. Failure to do this could result in

damage to pump.

6. Replace tank cover and secure latches.

PUMP SET UP AND OPERATION (CONT’D.)

7. Remove outlet-ﬁtting cap located on rear of tank cover. Connect a standard

garden hose onto outlet ﬁtting. Then place other end of garden hose at suitable

drain. The garden hose is not included with your vacuum.

8. Attach the 2½” (6.4 cm) hose to inlet on front of tank.

9. Place wet pick up elbow on the hose end and attach desired accessory to elbow.

Elbow must be in place during pump operation. Do not attempt pump operation

without elbow in place. Do not cover bleed hole in elbow. Failure to follow these

precautions will result in overﬁlling of unit and misting through exhaust port.

OPERATION

1. Plug the cord into a wall outlet and push the ON switch button.

2. Start vacuuming up the liquid. When there is at least 4” (10 cm) of liquid in the bottom of the tank, the

unit will automatically begin pumping.

3. The unit will vacuum up the liquids faster than the pump removes the liquid from the tank. The unit will

automatically shut off when the tank becomes full.

4. To empty a full tank, remove vacuum hose from the liquid. Do NOT lift the hose to drain the remaining

liquid into the tank. This will cause the unit to overﬁll and misting through the exhaust port will occur.

5. The ON/OFF switch must be manually held in the ON position for approximately 10 to 15 seconds to

allow the water level to be reduced sufﬁciently and then pumping will continue automatically. Once the

vacuum is pumping automatically, release the switch and allow it to operate on its own. ATTENTION:

HOLD SWITCH IN ON POSITION ONLY UNTIL WATER STARTS TO FLOW CONTINUOUSLY. RELEASE

SWITCH WHEN PUMPING BEGINS.

6. The unit will continue to discharge liquid until there is about 4” (10 cm) left in the tank. NOTE: If the unit

shuts off before liquid is pumped out repeat steps 5 and 6.

7. When the level of liquid lowers and the unit stops pumping repeat steps 2-7 to continue your cleaning

operation.

8. After the cleaning job has been completed, allow the liquid to be pumped until unit has stopped

pumping. There will be about 4” (10 cm) of liquid remaining in tank.

9. Make sure unit is in the off position. Disconnect plug from the wall receptacle and remove tank cover.

10. Remove and clean pump pick up assembly

11. Empty remaining liquid from tank. Before storing the vacuum or using for dry pick up, clean and dry the

interior of the tank and the underside of the tank cover. Clean and allow the foam sleeve to dry.

BLOWER FEATURE

Your vacuum can be used as a powerful blower. To use the blower feature, clear the hose of any debris or

obstructions.

For vacuums with a blower port cover (not standard on all models), unscrew blower port cover located

on the back of tank cover. The blower port cover is equipped with a retaining strap to prevent loss of the

cover. NOTE: For maximum performance when vacuuming, remove the blower port cover.

Insert machine hose end into blower port located on the back of the tank cover.

Twist the hose end slightly to tighten the connection. Caution should be used when using

as a blower due to the powerful force of air when using certain attachments.

WARNING –ALWAYS WEAR EYE PROTECTION TO PREVENT ROCKS OR

DEBRIS FROM BEING BLOWN OR RICOCHETING INTO THE EYES OR FACE WHICH CAN RESULT

IN SERIOUS INJURY.

PAGE 10

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Aspiradora para seco y húmedo de Shop-Vac

Shop-Vac

Shop-Vac SEP SERIES Manual de usuario

Shop-Vac

Shop-Vac SL14 SERIES Manual de usuario

Shop-Vac

Shop-Vac SE16-SQ650 Manual de usuario

Shop-Vac

Shop-Vac 92L Series Manual de usuario

Shop-Vac

Shop-Vac LB SERIES Manual de usuario

Shop-Vac

Shop-Vac MC SERIES Manual de usuario

Shop-Vac

Shop-Vac 87M Series Manual de usuario

Manuales populares de Aspiradora para seco y húmedo de otras marcas

Workshop

Workshop WS1600CAEX Manual de usuario

DURAVAC

DURAVAC CVQ810PF Manual de usuario