Installation method hen using vertical-direction-installation bracket.
1. Remove M5 Screw of u it i stallatio bracket a d i termediate i stallatio
bracket, a d remove L metal fitti gs.
2. Fix the u it to proper place with M4 screws i φ4.2 holes
*Fix the u it to proper place with M4 tappi g, or with uts from the backside.
*Fix with pla e washers a d spri g washers.
*Use two uts per o e bracket.
*Dista ce betwee ut hole for i stallatio a d the body is arrow, we
recomme d you to use bolt uts with hexago al holes a d fix with a
ball-poi t-type wre ch.
Installation method hen using angle-installation brackets
1.
Please fix to the hole of φ5.2 of the bracket with the M5 screw i the place
where it wa ts to i stallatio bracket a d i termediate bracket.
*Fix the body to proper place with M5 tappi g, or with uts from the backside.
*Fix with pla e washers a d spri g washers.
*Screw up tightly to fix the brackets completely.
2. Set up a gle, screw up M5 screws tightly.
*If tighte i g of M5 screws is lose, the i stalled a gle may be cha ged, a d may
make elimi atio effect lower.
6.3Wiring and Tubing
Co ect the provided power/sig al cable as show i the figure below.
*Securely co ect the grou d wire to the grou d. (type a or type b).
*Use the LPS (Limited Power Source) certified with IEC/EN60950-1.
*Securely i sert the co ector.
*The alarm wire i sulatio is ot pre-stripped, whe usi g the wire, strip away
a appropriate amou t of the i sulatio . The wire diameter is 22 AWG.
*The alarm sig al is a maximum of DC20V 0.2A
Status Power OFF RUN LED ON ALARM LED ON
Co tact sig al Ope Close Ope
*The optio al AC adapter does ot come with a alarm wire co ected. Whe
usi g the AC adapter, verify the co ector umber, a d the securely i sert
this wire i to the co ector i order to use it.
Co ect a Φ6 air tube ( ylo , soft ylo , or polyuretha e) to both sides of the u it.
*There are air co ectio ports o both sides of the u it. However, if sufficie t
air ca be supplied from just o e side, it is possible to supply air from o e
side for this product to work efficie tly. I this case, be sure to use a plug for
the Φ6 (or Φ8) air co ectio port o the u used side.
*The compressed air supplied must be clea , dry air. If a air filter is ecessary
for the air supply equipme t you are usi g, use a i -li e filter system or
similar item.
*The maximum air pressure that ca be supplied to the u it is 0.5MPa.
Because this u it does ot i clude a regulator speed co troller or similar
fu ctio , a air pressure regulator must be provided by the user.
*As the amou t of compressed air co sumed varies depe di g o the u it
le gth of your model, the air pressure level, the diameter a d the le gth of
pipi g, use devices that are suitable for the co ditio s of use.
Piping of measurement of flo ing quantity of air
Air flo ith L-type (lo air consumption type) nozzle.
*This data is experime tal
Le gth Air pressure (MPa)
0.1 0.2 0.3 0.4 0.5
350 11 15 17 19 21
600 23 28 32 37 40
850 34 41 48 54 59
1100 43 43 62 71 77
1350 51 62 75 85 96
1600 58 74 87 100 113
1850 80 103 121 138 154
2100 93 117 139 159 175
2350 104 132 153 175 194
2600 113 143 168 191 212
2850 122 157 183 208 229
3100 131 168 195 222 246
Air flow (l/mi )
H-type (high speed type) nozzle *This data is experime tal
Le gth Air pressure (MPa)
0.1 0.2 0.3 0.4 0.5
350 23 28 31 35 39
600 42 52 59 67 73
850 58 71 83 94 105
1100 68 88 101 117 133
1350 75 98 116 132 149
1600 80 105 125 145 162
1850 138 171 192 225 256
2100 159 191 215 252 283
2350 163 200 235 277 308
2600 174 211 250 295 332
2850 178 218 260 306 349
3100 185 223 268 315 363
Air fllow(l/mi )
7. Operating the Product
Setup before Starting Operation
Check the io izer wiri g a d air tubi g.
Supply air to the u it from the air equipme t that is used.
*Use air pressure off 0.5MPa or less.
Supply DC24V power to the u it. The POWER LED a d RUN LED o the u it
illumi ate a d electrostatic elimi atio starts.
*If the optio al power adapter is used, supply AC100-240V, 50/60Hz
Steps hen Stopping Operation
Stop supplyi g of power to the u it.
Stop supplyi g of air.
Canceling the Alarm
*Because this device utilizes high voltage, if a safety or operati g problem is
detected, the high voltage is shut off. At this time the RUN LED tur s OFF
a d the ALARM LED illumi ates. The system is co figured so that the
system ca ot be restarted u it the alarm has bee reset.
*Whe the ALARM LED is illumi ated, refer to “9. Troubleshooti g” i this
ma ual a d correct the problem before restarti g operatio .
Stop supplyi g of power to the u it.
Remove problems referri g “9.Trouble shooti g” i this ma ual.
Start supplyi g of power to the u it agai .
Cancelling operation of CLEANING
Push the CLEANING TIMER RESET butto more over 2 seco ds while RUN
status. Timer will be reset.
Maintenance
*This device should be i stalled a d used i a locatio where it will ot co tact
water, oil, or similar substa ces. However if water, oil, or a other substa ce
co tacts the product, immediately tur OFF the power a d wipe away the
substa ce with a cloth or other item. Use particular cautio at the high
voltage sectio s a d surrou di g area.
*If the emitter eedle a d surrou di g area become fouled, the electrostatic
elimi atio effects will be reduced. If the electrostatic elimi atio effects
dimi ish, clea the emitter eedle a d the surrou di g area periodically ( i
particular, the emitter eedle ozzle.) for preve ti g drop of elimi atio effect.
Be sure to tur the power OFF beforeha d.
Cleaning the Emitter Needle nozzle
*Be sure to tur the power OFF before clea i g the emitter eedle ozzle.
Failure to do so may result i electric shock or malfu ctio of this u it.
*The emitter eedle ozzle is removable. Whe dust or other substa ces
become oticeable at the locatio where the product is used, remove the
emitter eedle ozzle a d take it to a other locatio for clea i g.
*The tip of the emitter eedle is extremely sharp. Use sufficie t care whe
ha dli g it. The eedle tip ca cause i jury.
*If the emitter eedle tip accide tally becomes be t or chipped, or resi part of
discharge eedle is damaged duri g clea i g, replace the emitter eedle
ozzle. If the emitter eedle ozzle is ot replaced, the full product
performa ce will ot be achieved or it may cause some accide ts.
1. Verify that the power is tur ed OFF (disco ected).
2. Verify that the supply of air is stopped.
*To perform clea i g without removi g the emitter eedle ozzle, proceed to ④
3. Twist the emitter eedle ozzle cou terclockwise i order to remove it from
the u it.
*It is possible that the O-ri g may become stuck to the u it whe the emitter
eedle ozzle is removed. If this occurs, remove the O-ri g, taki g care ot
to lose or damage it. If the O-ri g is ot rei stalled after clea i g, it will cause
air leakage, preve ti g full performa ce from bei g achieved.
4. Use cotto swabs or a similar thi g moiste ed with alcohol to wipe away the
fouli g from i side the emitter ozzle, the emitter eedle area, a d other areas
that are dirty.
*If o ly performi g clea i g without removi g the emitter eedle ozzle, the
clea i g is ow fi ished. Verify that the tip of the emitter eedle is ot be t or
chipped, a d that resi part of discharge eedle is damaged.
*Be sure to allow the alcohol to fully evaporate (dry) after clea i g.
*Whe you clea discharge eedles take off from the body, do ot clea
eedles soaked i alcohol. If you do so, it may cause residual of alcohol
i side discharge eedles a d because of its structure, it ca ot be easily
dried, so it may lead to damage of the body whe you apply high voltage
agai .
5. Securely rei stall the emitter eedle ozzle by placi g it i its origi al positio
a d tur i g it clockwise u til it stops.
*Whe rei stalli g the emitter eedle ozzle, be sure to verify that the O-ri g
is correctly positio ed o the ozzle before i stalli g.
5. Verify that the tip of the emitter eedle ozzle is ot be t or chipped, a d that
resi part of discharge eedle is damaged, a d that the emitter eedle u it is
securely i stalled.
Replacing the Emitter Needle Nozzle
*Because the emitter eedle ozzle is co sumable part, it eve tually becomes
ecessary to replace it. I additio , the emitter eedle or the emitter eedle
ozzle may become be t or chipped duri g mai te a ce or due to accide ts.
If the tip of the emitter eedle becomes wor through use or damaged, it may
become impossible to achieve this product’s full performa ce. I this case,
replace with a ew emitter eedle. (Refer to “Optio al Parts.”)
1. Verify that the power is tur ed OFF (disco ected).
2. Verify that the supply of air is stopped.
3. Twist the old emitter eedle ozzle cou terclockwise i order to remove it from
the u it.
*It is possible that the O-ri g may become stuck to the u it whe the emitter
eedle ozzle is removed. If this occurs, remove the O-ri g carefully.
4. Securely i stall the ew emitter eedle ozzle by placi g it i the positio a d
tur i g it clockwise u til it stops.
*Whe i stalli g the ew emitter eedle ozzle, be sure to verify that the
O-ri g is i the desig ated locatio o the ozzle before i stalli g.
5. Verify that the tip of the emitter eedle is ot be t or chipped, a d that resi
part of discharge eedle is damaged, a d that the emitter eedle u it is
securely i stalled.
9. Troubleshooting
*The POWER LED does ot illumi ate.
→Verify that the wiri g a d power source are co ected correctly.
*The POWER LED illumi ates, but the RUN LED does ot illumi ate.
→Verify that the grou d wire is securely co ected to the grou d.
→Check whether the ALARM LED is illumi ated.
*The ALARM LED is illumi ated.
→Check whether the emitter eedle or surrou di g area has become fouled.
→Verify that o grou ded objects are i co tact with the u it.
→Verify that there is o loose ess i the screws at the part that co ects the
emitter cou ter electrode.
→Verify that the u it securely grou ded.
→Verify that the emitter eedle ozzle is ot loose.
→Please co firm if some ge eratio sources of electromag etic oise are ot
arou d the product.
10. Optional Parts
Low co sumptio air ozzle (Tu gste ) : OCABX-NDL-LW
Low co sumptio air ozzle (Silico ) : OCABX-NDL-LS
Low co sumptio air ozzle (Glass) : OCABX-NDL-LG
High speed air ozzle (Tu gste ) : OCABX-NDL-HW
High speed air ozzle (Silico ) : OCABX-NDL-HS
High speed air ozzle (Glass) : OCABX-NDL-HG
I termediate bracket : OCABX-SUSP-A
AC adapter : OCAB-DA2
Exte sio Cable : OCABX-ENC3M
SHISHIDO ELECTROSTATIC, LTD. http://www.shishido-esd.co.jp/
Overseas Departme t, Tokyo Bra ch
Shishido Bldg, 1-3-3 Higashi-Yukigaya, Ota-ku, Tokyo 145-0065
Ke _sakamoto_t2g@shishido-esd.co.jp
Tel +81-3-3727-0162 Fax +81-3-3727-0342
Head Office
9F-918, Maru ouchi Bldg, 2-4-1 Maru ouchi, Chiyoda-ku Tokyo 100-6309
3:DC24V
6:DC0V
5:GND
1:ALARM
4:ALARM MAX DC30V 0.2A
Main Circuit
CABX Inside Circuit CABX Outside Circuit
LOAD
Power/Sig al cable
White
Not use
Red
Yellow
Gree
Black
150mA
INPUT :24V DC
AIR PRESSURE:0.01-0.5MPa(Clean and Dry Air Only)
