Shinsei DP-2E Manual de usuario

* Read this manual thoroughly, and do not perform installation, operation,

maintenance, or inspection unless you fully understand all of the contents.

* Keep this manual in a safe place where you can refer to it easily while

installing, operating, and carrying out maintenance or inspections.

Mobile Printer

DP-2E

Mobile Printer

Instruction Manual

IMPORTANT

■Preface...

Thank you for selecting our model DP-2E.

This product does not contain toxic substances specied by

the RoHS and WEEE Directives.

This machine is a mobile printer developed based on a state-

of-the-art electronics technology and accumulated experiences.

For proper and safe use of this machine, read this instruction

manual thoroughly to become aware of the machine and the

related precautions before working for the installation and

operation.

After the installation, keep this manual at the place where

you can refer to whenever it is necessary.

SHINSEI INDUSTRIES Co., Ltd., 2010

All rights are reserved. No part of this publication may be reproduced,

stored in a retrieval system, or transmitted, in any form, or by any

means, mechanical, electronic, photocopying, recording, or otherwise,

without prior written permission of SHINSEI.

FCC WARNING

Changes or modications not expressly approved by the party

responsible for compliance could void the user's authority to

operate the equipment.

NOTICE

This equipment has been tested and found to comply with

the limits for a Class A digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the

equipment is operated in a commercial environment.

This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio

communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own

expense.

This transmitter must not be co-located or operated in

conjunction with any other antenna or transmitter.

This equipment complies with FCC radiation exposure limites

set forth for controlled equipment and meets the FCC radio

frequency (RF) Exposure Guidelines in Supplement C to OET65.

The product is mobile device, the separation distance between

the user and the device's radiating element is greater than 20cm.

The maximum E.I.R.P of the device is 3.523mW, which is

less than RF Expo.

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) this device may not cause

harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

This device complies with Part 15 of FCC Rules and RSS-Gen

of IC Rules.

Operation is subject to the following two conditions: (1) this

device may not cause interference, and (2) this device must

accept any interference, including interference that may cause

undesired operaton of this device.

This equipment complies with IC radiation exposure limits

set forth for uncontrolled equipment and meets RSS-102 of

the IC radio frequency (RF) Exposure rules. The product is

mobile device, the separation distance between the user and

the device's radiating element is greater than 20cm.

The maximum E.I.R.P of the device is 3.523mW, which is

less than RF Expo.

Europe - EU Declaration of Conformity

We, Shinsei Industries Co., Ltd. hereby declare that this device,

model DP-2E is in compliance with the essential requirements

and other relevant provisions of the R&TTE Directive 1999/5/EC.

■ BluetoothTM Communications

This device with built-in wireless telecommunication equipment

conforms to the standards, required in the region where the

device is used. This device assumes an interference distance

of about ten meters or less. Using this device near microwave

ovens, wireless LAN equipment, etc. may signicantly reduce

the communication distance or make communication impossible.

Do not disassemble or modify this device.

This device is equipped with a Bluetooth module that obtained

product certication.

BluetoothTM is a trademark of Bluetooth SIG, Inc., U.S.A., and

is used herein under license.

1. Precaution Symbols ............................................................................ 7

2. For your longer use ............................................................................. 11

3. Conrmation of This Machine ............................................................. 13

3-1. Printer Unit .............................................................................. 13

3-2. Accessories ............................................................................. 14

4. Optional Accessories ..................... ................................................... 15

5. Names and Functions of Each Part .................................................... 16

6. When using this machine with the battery pack ................................. 20

6-1. Installing the battery pack .......................................................... 20

6-2. Removing the battery pack ........................................................ 22

7. Charging the battery pack ................................................................... 23

7-1. Battery charge is needed in one of the following cases ............. 23

7-2. Battery charging procedure ....................................................... 24

7-3. Before using the battery pack .................................................... 26

8. When charging the battery pack with

the charger adapter (sold separately) ................................................. 28

　 8-1. Installing the charger adapter ...................................................... 28

8-2. Removing the charger adapter .................................................... 29

9. Setting the media roll ........................................................................... 30

9-1. In the case of printing labels in the Tear-Off mode ...................... 30

9-2. In the case of printing labels in the Peel-Off mode ...................... 33

■Table of Contents

10. Power ON-OFF ................................................................................... 37

10-1. Turn on the power ..................................................................... 37

10-2. Turn off the power ..................................................................... 37

11. Contrast adjustment of the liquid crystal display ................................. 38

12. Adjustment of the backlight lighting time ............................................. 40

13. Test Printing ........................................................................................ 42

13-1. Test printing method 1 .............................................................. 42

13-2. Test printing method 2 .............................................................. 44

14. Printing the Conguration List ............................................................ 45

15. Printer Info........................................................................................... 47

16. Conrmation of BluetoothTM communication set value ....................... 49

17. Automtic adjustment of the sensor ..................................................... 53

17-1. Automatic adjustment of the label sensor ................................ 53

17-2. Automatic adjustment of the peel sensor ................................. 56

18. Connecting the USB (mini-B) ............................................................ 57

19. Using the BluetoothTM communications .............................................. 57

20. Label issuing mode ........................................................................... 58

21. Error messages .................................................................................. 59

22. Daily Check and Cleaning Method .................................................... 61

22-1. Printing check (Test pattern printing) ....................................... 61

22-2. Execution of the head check ................................................... 62

22-3. Cleaning of the thermal print head .......................................... 62

22-4. Cleaning of the platen roller and the peel roller ...................... 64

22-5. Cleaning of each sensor .......................................................... 65

23. Specications of this machine .....,,..................................................... 66

24. Important Notices ............................................................................... 69

■Table of Contents

This product is manufactured for use according to proper

procedures by a qualied operator and only for the

purposes described in this manual.

Precaution symbols in this manual are divided into two

categories, depending on the level of danger, or

seriousness of potential injury. The denition of each

precaution is shown below. Failure to heed these

precautions may result in bodily injury or damage to the

machine.

1. Precaution Symbols

This machine is manufactured for use according to proper

procedures by a qualied person and only for the purposes

described in this manual. The following symbols are used

in this manual.

Always heed the information provided in this manual.

Failure to heed precautions can result in personal injury or

property damage.

Heed the following precautions information provided in

this manual for your safety.

Indicates information that, if not heeded,

could possibly result in loss of lie or serious

injury.

Indicates information that, if not heeded,

could result in relatively serious or minor

injury, damage to the machine, or faulty

operation.

CAUTION

WARNING

Do not disassemble or modify the printer unit,

battery pack, battery charger, charger adapter, etc.

Doing so may result in injury or cause the machine

to break down.

∑ Doing so may cause damage, short-circuit, or

ignition, and may result in electric shock, burn, or re.

Do not keep the battery pack with metals.

∑ Doing so may cause a re or electric shock due to

short-circuit.

Do not allow the printer unit, battery pack, battery

charger, or charger adapter to come in contact

with water or get accumulation of dust.

Doing so may result in re or cause the machine to

break down.

∑ Continued use may cause a re or electric shock.

Do not give strong shock such as dropping and

throwing the printer unit.

∑ Doing so may cause damage, short-circuit, or

ignition, and may result in electric shock, burn,

or re.

Do not charge anything other than the specied

battery pack with the battery charger.

∑ The battery pack may cause heat, burst, or

ignition.

WARNING

・

Do not charge anything other than the specied

battery pack with the battery charger.

・ The battery pack may cause heat, burst, or ignition.

・

Risk of explosion if battery is replaced by an incorrect

type. Dispose of used batteries according to the instructions.

Do not touch the thermal print head because it will

be exposed when the cover is opened.

∑ When replacing labels immediately after using the

machine, be careful not to get burned due to

overheating of the thermal print head.

∑ Do not touch the thermal print head as your hand

oil may cause the deterioration.

Do not leave the battery pack charged for a long

time.

After the charge, make sure to pull out the plug

of the power supply cord of the battery charger or

the charger adapter from the AC outlet.

The operation time may become less because the

battery pack is naturally discharged and the power

decreases. (It is not a breakdown).

CAUTION

・

Change or modications not expressly approved by

the party responsible for compliance could void the

user's authority to operate the equipment.

After using this machine or when not using it for a

long time, take out the battery pack and pull out

the power plug of the charger adapter from the AC

outlet for safety.

Do not charge anything other than the specied

battery pack (lithium-ion battery).

∑ Follow the local regulation when disposal.

Do not place this machine on an unstable place.

∑ Doing so may fall and injury.

Remove dusts regularly after pulling out the power

plug of the charger adapter from the AC outlet.

∑ If dusts are accumulated around the AC outlet,

it may cause leak current and re.

CAUTION

・

Tabla de contenidos

Manuales populares de Impresora de otras marcas

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series Manual de usuario

Evolis

Evolis Elypso Manual de usuario

Kyocera

Kyocera FS-9530DN Manual de usuario

Canon

Canon LASER SHOT LBP-1210 Manual de usuario

Samsung

Samsung BIXOLON SRP-350plusF Manual de usuario

Canon

Canon PIXMA PRO-1 Series Manual de usuario

Canon

Canon PIXMA G3560 Guía de configuración

Dell

Dell Color Laser Printer 2130cn Manual de usuario

Tektronix

Tektronix Phaser 840 Manual de usuario

Epson

Epson ET-7750 Instrucciones de funcionamiento

Canon

Canon CLBR 460ps Manual de usuario

Eltron

Eltron P210 Guide Manual de usuario

Ricoh

Ricoh MD-P1 Manual de usuario

Epson

Epson SC-F7100 series Manual de usuario

Epson

Epson Stylus C40UX Manual de usuario

Canon

Canon imagePASS-A2 Manual de usuario

Canon

Canon S820D Manual de usuario