Shineway Tech OCI-20B Manual de usuario

OCI-20B User’s Manual

Shineway Technologies, Inc. I

OCI-20B

Optical Connector Inspector

User’s Manual

Shineway Technologies, Inc.

OCI-20B User’s Manual

Shineway Technologies, Inc. II

Thank you for purchasing ShinewayTechOCI-20B Optical Connector Inspector.

Please read carefully this User’s Manual before operating, which can be of great help.

In order to prevent improper operation of DC converter, please read user manual carefully.

Prevent this product from water and liquid, otherwise, electrical shock and fire danger may

occur.

For you safety, please use only the DC converter provided. ( The manufacturer will not

responsible for any losses caused by DC converter not provided by the manufacturer )

!! Important !!

Please only use the socket matched with DC converter. Use of improper socket may

cause electrical and fire damage.

Please firmly plug the DC converter into theAC socket panel.

Do not open the cover!

It may cause electrical shock

Touch DC convert parts may cause electrical shock

A. Do not use damaged battery

B. Do not use battery over the specified time period

C. When first use or the battery has not been used for several months, please recharge

the battery before use.

D. In order to protect your battery, please fully charge the battery before use. The battery

must be fully discharged before you charge it again.

E. Overcharging or over-discharging will shorten the battery life

F. If the usage period of fully charged battery is greatly shorter than new battery, you

need to change your battery

G. Battery is consumable item; its life will be shortened from first use

H. Do not let the DC converter with conductors have short circuit, otherwise electrical or

fire damage may occur.

This product is controlled by microprocessor; improper use may cause

the monitor stop operating. Please read the manual carefully to enjoy

the performance.

If battery is not fully charged, it may cause serious system error when

recording and transferring video files

OCI-20B User’s Manual

Shineway Technologies, Inc. III

Table of Contents

OCI-20B-P Probe Overview..........................................................................................................1

Components Introduction..............................................................................................................1

Major Structure .......................................................................................................................1

Inspection Lens.......................................................................................................................2

Barrel Assembly......................................................................................................................2

Inspection Tips........................................................................................................................2

Key Features & Specification........................................................................................................3

Magnification...................................................................................................................................3

Resolution................................................................................................................................3

Enlarged Zones ......................................................................................................................3

Specification............................................................................................................................3

Major Function................................................................................................................................4

OCI-20B-D Display Overview.......................................................................................................4

Component Introduction................................................................................................................4

Panel of Display......................................................................................................................4

Bottom end of Display............................................................................................................5

Specification & Performance ........................................................................................................5

Parts Specification..................................................................................................................5

High Performance ..................................................................................................................6

Operating Guideline.......................................................................................................................6

Mode Introduction...................................................................................................................6

Image Check and Record.....................................................................................................6

Files Playback.........................................................................................................................7

Systems Setting......................................................................................................................7

OCI-20B Microscope Installation .................................................................................................8

Warranty Information .....................................................................................................................9

Contact Customer Service............................................................................................................9

OCI-20B User’s Manual

Shineway Technologies, Inc. 1

OCI-20B-P Probe Overview

OCI-20B Optical Connector Inspector is used to inspect end-face of fibers and check

the optic connectivity. It magnifies fibers of 125μm diameter 650 times, enlarging picture

through a video signal to the display where the status of fiber end-face is showed

clearly.

Not only portable, easily in-hand, OCI-20B is also multi-functional. It can detect simplex

and ribbon fiber ends located in both male and female connectors, as well as other fiber

units. Also, working comfortably is it’s another feature. Eliminating the need to finding

solutions for hard-to-reach areas inspection, OCI-20B can detect connectors even

installed on the backside of patch panels or inside hardware devices, providing you a

completely convenience for checking.

Components Introduction

Major Structure

A. Handle Body: the handle houses components like CCD camera, ray apparatus

OCI-20B User’s Manual

Shineway Technologies, Inc. 2

structure, optical routine system, coaxial lamp-house, focus control, video output,

power supply system and PAL signal system.

B. The inner structure of the Handle is compact and complex, long time working may

cause handle body heating. This isn’t the mechanical faulty but normal phenomena.

Unauthorized disassembling may cause damage to OCI-20B.

Inspection Lens

A. Optical magnification system is in the front of handle body, the beginning of which

comes a lens-bar.

B. The Barrel Assembly, mounted on body outside the lens-bar, can match different

types of tips. The lens-bar will be adjusted according to the focus control.

Note: It may cost a lot if the lens or lens-bar is damaged, which have the image formed

and be the cores of probes.

Barrel Assembly

BarrelAssembly plays a vital role in connecting or matching different types of tips.

Note: It will have a serious effect on the image performance once the inner conical

surface from the barrel assembly is hit or impacted.

Inspection Tips

There are specific tips interchangeable for different types of connectors, which allow

you to inspect the fiber surface whether on the backside of the patch panels or inside

hard devices such hard-to-reach areas.

Tips Installation Note:

A. Conical surfaces of tips should be well protected, if crushed or hit, can’t be used

again.

B. Mare sure conical surfaces of tips clean enough prior to installation.

C. Have a strong tips attachment during installation.

D. Have a proper screw on the nuts during installation.

OCI-20B User’s Manual

Shineway Technologies, Inc. 3

E. Mind the tip before removal of the nut during disassemble.

Key Features & Specification

Magnification

The optical and picture magnification can reach up to 12×and 650×respectively.

Different size display has correspondingly different magnification; the table of

magnification is as below:

Note: 1. The size of enlarged picture is the measured directly based on the 1.25um

resolution.

2. The magnification is calculated by the following equation:

Enlarged size (um)÷1.25um = M

Resolution

The resolution of the probe can reach up to 1.25um whereas

the national standard is only 2um.

Enlarged Zones

The enlarged size for the ferrule diameter can reach up to 300×280µm, Also the largest

visible area can reach up to 600×570μm when adjusting the probe.

Specification

Resolution

1.25μm

Zoom

12X

Field of Vision

300×280μm

Sensor

1/3IN black-and-white CCD

Light Source

BLUE-LED (100000hrs above)

Focus

Manual coaxial focus

Connector

4PIN

Operating Temperature

-5℃~50℃

Weight

170g

Dimensions (H×W×T)

162×96×40mm

Display

Index

2.5 IN.

3.5 IN.

5.6 IN.

9 IN.

Diameter

1.857

2.5

4.5

8.1

Magnification

150

200

360

650

OCI-20B User’s Manual

Shineway Technologies, Inc. 4

Major Function

To inspect fiber ends of both simplex and ribbon types

1. To inspect male fiber ends, which refer to the end of patch cords or pigtails.

2. To inspect female fiber ends, which refer to the end of port through adapters or

inside devices.

3. To inspect ferrules of both 2.5mm and 1.25mm diameters, fixed in the middle of

the fiber. Exposed ones are excluded in the test.

To output PAL or NTSC video signal of the enlarged fiber image

OCI-20B-D Display Overview

Component Introduction

Panel of Display

1. Enter: operation function, control brightness

and contrast

2. Back: back to the previous interface

3. Delete: delete or copy

4. Record: video recording

5. Switch: switch for CH1/CH2 image channels

Top end of Display

1. USB2.0 Connector: output port, to

connect OTG/U desk or computer

directly (Only operational when

entering).

2. SD card socket: to house SD card

where the standard allocation is 2G,

Maximum memory support can reach to 16G.

3. Power on/off: 3 seconds pressing for power on or off.

4. Microphone recording: press for voice recording, used for clarifying or compiling

fiber images.

5. Indicator: yellow light indicates open-state while red light indicates charged-state.

OCI-20B User’s Manual

Shineway Technologies, Inc. 5

Bottom end of Display

1. CH1 Image Input: Connector: press

CH1/CH2 key to display CH1 image.

2. Charger Connector.

3. Earphone Connector: adjust the

volume via up/down keys.

4. CH2 Image Input Connector: press

CH1/CH2 key to display CH2 image.

5. Video Output: connect to have voice output.

6. Reset: can put slim sticks in the hole for recovery from dead halt.

7. Key lock: can’t operate when locked.

Specification & Performance

Parts Specification

Video

Frequency

FM 2.4MHz

2.5 Inch Display

960x240 LCD

Output Mode

NTSC / PAL

Video Mode

NTSC / PAL

Resolution

640×480 / 320×240

Video Format

MPEG-4/AVI

Media Format

MPEG-4/AVI/ASF/MOV

Audio

Frequency Range

20HZ-20KHz

Output Channel

Stereo

Earphone Output

L 20MW+R 20mW [160](Max volume)

Media Format

MP3/WAV/MPEG-1

Storage

Size

128MB/1GB

Storage Media

SD/MMC/U disk

Operation Interface

IBM-PC

Windows 98SE.ME.2000,XP

USB

USB 2.0; USB OTG2.0

Disk File Format

FAT32

Language

Chinese/English

Power Source

Power Supply

DC 5V, 2A

Inner Battery

Lithium battery 1800Mah,

Max Charging Time: 3 hours;

Media play ≥8 hours

OCI-20B User’s Manual

Shineway Technologies, Inc. 6

High Performance

1. 960 x 240 definition , 2.5inch LCD monitor

2. Image recording, timing display

3. Two channels for image signal input CH1/CH2, manually switching

4. Sensitive microphone installed for sound recording

5. Functions of key-locked ,stand-by and recording

6. Storage (128MB internal memory, SD card optional provided ),16G support

7. Mobile disk optional provided

8. Can upload files of music and video or other kinds through USB 2.0

9. Earphone interface, sound output support

10. Battery safe and high volume, ≥9 hours continuous working time, 7 hours

continuous recording time.

11. Dual version for interface (English/Chinese)

Operating Guideline

Mode Introduction

Hold the Power button On/Off for 3

Seconds to turn on or off the monitor and

enter the interface.

Mode Selection:

1. Image Check and Record –Check and Record video signals form CH1or CH2

2. Play Back –Video Recorded File Playback, from Internal Memory, SD Card or

Portable Disk etc.

3. Setting –System Preset for Different Functions

Image Check and Record

1. Press [Enter] to check the image from

CH1 or CH2 detected by the probes.

Please be sure

2. Press [Enter] again if necessary to adjust

the brightness/ contrast, control the proper

range via up/down keys. Please note that

color is no need to adjust.

Brightness: the suitable value will be 6.

Contrast: the suitable value will be 4.

3. When finished, press [Enter] again to exit.

OCI-20B User’s Manual

Shineway Technologies, Inc. 7

4. Press [Record] to record the being image and timing, When working, voice is

recorded at the same time, which can be used as indentifying different files. Press

left/right keys to control the recording speed, Press up/down keys to control the

volume. When finished, press [ Back] to exit (shown as picture above)

Files Playback

1. Press the right key to choose the PLAYBACK mode.

2. Press [Enter] to see the files recorded. You need to preset to choose the files

whether from internal memory, SD card or U disk. When no SD card or U disk, files

are shown from system. When having

SD card or portable disk but no setting

before, files are shown from SD card

automatically

3. When entered, press up/down keys to

choose files labeled. When opened,

press [Enter] to stop the video to observe,

or files will be displayed continuously.

4. Press [Delete] to decide to delete or copy

files recorded, Press [Enter] to confirm.

5. When finished, press [Back] to exit (as pictures shown above).

Systems Setting

1. Press [Enter] to choose the setting

option.

2. Press arrow keys to make choice.

3. Press [Enter] to confirm and operate.

Setting Options Available

Record Setting–set before record and

playback

- NandFlash (internal memory, 128MB)

- 2G SD Card

- External HDD (portable disk for option)

Memory Status –check the memory state

- NandFlash (internal memory)

- SD Card

- External HDD (will not display if no use)

Tabla de contenidos

Manuales populares de Instrumento analítico de otras marcas

Cocraft

Cocraft NLT04 Manual de usuario

M&C

M&C GENTWO PMA1000 Manual de usuario

MICRO-EPSILON

MICRO-EPSILON optoncdt 1700 Manual de usuario

CONDTROL

CONDTROL XP4 PRO Manual de usuario

Extech Instruments

Extech Instruments BR200 Manual de usuario

Dewetron

Dewetron DEWE-30-16 Manual del producto

EXTOL PREMIUM

EXTOL PREMIUM 8820043 Instrucciones de instalación y funcionamiento

RIDGID

RIDGID SeeSnake Compact Manual de usuario

Teledyne

Teledyne 3000PA Manual de usuario

YDLIDAR

YDLIDAR TIA Manual de usuario

Olympus

Olympus IPLEX FX Series Manual de usuario

Bosch

Bosch GLM 50 C Professional Manual de usuario

Reflecta

Reflecta DigiEndoscope Manual de usuario

Chinavision

Chinavision CVACZ-G696 Instrucciones de montaje

Fuji Electric

Fuji Electric ZKMA Manual de usuario

Teledyne

Teledyne 3300TA Manual de usuario

VOLTCRAFT

VOLTCRAFT IC-100HD Manual de usuario

RIDGID

RIDGID micro CA-25 Manual de usuario