Shimmer NEUROLYNQ Manual de usuario
1
NEUROLYNQ USER GUIDE V3.1
Rev. a
Copyright © Shimmer, 2019
CONTENTS
Setup:
1. What’s new in this Release
2. Introduction
3. Inventory
4. NeuroLynQ Setup
5. Install Hardware
6. Install Software
Software Explained:
7. Licensing
8. Conduct a NeuroLynQ@Home Trial
9. Home Screen
10. Manage Devices –part 1
11. Live Data
12. Manage Devices –part 2
13. Manage Data
14. Analytics
15. Appendices
•Program NeuroLynQ sensor Firmware
•Program Span Firmware
•Application Settings
•LED behaviour
•Useful Things to know..
•Troubleshooting
•Known Issues
2
WHAT’SNEW IN THIS RELEASE
NeuroLynQ v3.1 brings a number of new features to perform the
analysis of recorded NeuroLynQ@Home trial.
Updates:
•Option to Load Event Marker File
•New Manage Data tab buttons –Refresh, Download
•NeuroLynQ@Home Trial Settings panel
3
INTRODUCTION
•The Shimmer NeuroLynQ solution integrates both hardware
and software to provide unprecedented insight into the
emotional responses and implicit reactions of a large group.
•The solution can be applied to a variety of applications such as:
•Focus Groups
•Movie Screenings
•Mock Jury Trials
•Video Ad Testing
•Athletic Events
•Pilot Screenings
•Education
•Workforce training
4
NEUROLYNQ SETUP (SENSOR)
ECG electrodes:
Right chest (under collarbone)
Left wrist
GSR electrodes:
Palmar surface of index fingers
NeuroLynQ Sensor Unit
NeuroLynQ Sensor Unit
Note: It is not mandatory to connect the ECG electrodes to the subjects if you do not wish to capture ECG
and HR data. NeuroLynQ hardware and software will function perfectly fine with just the GSR electrodes
6
NEUROLYNQ SETUP (SYSTEM)
Note: It is recommended to insert the webcam and NeuroLynQ span directly into the USB ports on the laptop running NeuroLynQ via the
active USB extenders and not through a USB hub. If the laptop running NeuroLynQ has only two USB ports then it is recommended to
allocate one USB port for the webcam and the other USB port for the USB hub.
Recommendations
1. It is preferable if the NeuroLynQ admin is
located in another room to the
NeuroLynQ subject(s) or at the very least
outside of the subject(s) line of sight.
2. Position the span radio module where it
has the best line of sight with each
NeuroLynQ sensor (often this is above
the subjects).
3. Position the webcam so that the stimulus
can be easily observed by the NeuroLynQ
admin so that event marking is easier.
INSTALL HARDWARE (1/8)
STEP 1 –Connect the USB Hub to its AC adapter. Insert the power plug into a mains power socket.
STEP 2 –Connect the USB Hub to its USB cable. Insert the other end into a USB Port of the PC either directly or via the supplied
USB extender and UTP cable.
STEP 3 –Connect each Base with an AC adapter. Ensure you match the AC adapters accordingly, 3.5A for Base6 and 5A for Base15.
STEP 4 –Plug a power cable into each AC adapter and the other end into a mains power socket.
STEP 5 –Connect each Base to an USB Port on the PC (using the supplied USB-to-MiniUSB cable). Alternatively, the extra USB Port
on a Base can be used to link other Bases together in a chain.
STEP 6 –Windows will now install the drivers for the Base. Status feedback is given in Windows’ system tray (right bottom corner
of the screen):
N.B. The driver installation can take up to a few minutes at the end of which the system tray icon will disappear. In case you are
not sure if the installation has finished, proceed to the next STEP to verify the driver installation.
N.B. The screenshots in this section are made using Windows 7. The screens on your PC might look slightly different.
7
INSTALL HARDWARE (2/8)
STEP 7 –Verify driver installation:
A. Run the Device Manager: Press [Windows Key] + R; type devmgmt.msc; click “OK”.
B. Expand the ‘Universal Serial Bus Controllers’ category.
A B
8
Four USB Serial Converters (A,B,C,D)
are installed For each Base6 or Base15.
Two USB Serial Converters (A, B)
are installed for each Span.
INSTALL HARDWARE (3/8)
STEP 8 –Verify driver installation - continued:
C. Right-click on one of the USB Serial Converters; click Properties.
D. Go to “Driver”; check if FTDI Driver v2.12.0.0 or later is installed → Correct Driver has been installed!
E. Go to “Advanced”; make sure Load VCP is checked.
F. Repeat for the other USB Serial converters. If the correct driver is installed for all USB Serial Converters the driver
installation has been successful and the hardware is successfully setup – proceed to “Installing the software”.
CD
9
E
Tabla de contenidos
Manuales populares de Equipo de laboratorio de otras marcas
Agilent Technologies
Agilent Technologies 5800 ICP-OES Manual de usuario
Endress+Hauser
Endress+Hauser Cleanfit CPA875 Manual de usuario
NI
NI PXI-5422 Manual
Collomix
Collomix Aqix Manual de usuario
SPEX SamplePrep
SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario
Ocean Insight
Ocean Insight FLAME-NIR+ Manual de usuario
