Sharp AR-FN1N Manual de usuario

CODE: 00ZARFN1N/A1E

DIGITAL COPIER

OPTION FINISHER

MODEL AR-FN1N

AR-FN1N

Parts marked with "!" is important for maintaining the safety of the set. Be sure to replace these parts with specified

ones for maintaining the safety and performance of the set.

SHARP CORPORATION

This document has been published to be used

for after sales service only.

The contents are subject to change without notice.

[Note]

•This Service Manual describes only the differences from AR-FN1. The items

which are not described in this Manual are common with the AR-FN1.

•The chapters marked with ∗are partly modified from those of the AR-FN1.

Refer to the attached list of changes.

*[ 1 ] SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

*[ 2 ] UNPACKING AND INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

*[ 3 ] EXTERNAL VIEW AND INTERNAL STRUCTURE . . . . . . . . . . . . . . . 3-1

*[ 4 ] OPERATIONAL DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

*[ 5 ] DISASSEMBLY AND ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

*[ 6 ] ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

*[ 7 ] MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

*[ 8 ] TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

*[ 9 ] CIRCUIT DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

*[10] ELECTRICAL SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1

PARTS GUIDE

CONTENTS

List of changes from AR-FN1 to AR-FN1N

No. AR-FN1 AR-FN1N

Page Item Content Change Remark

1 1-1 [1]-11 Power consumption

Max. 60W Changed to Max. 70W.

2 2-1 [2]-2 Installation 2. Add the following descriptions to the instal-

lation procedure.

Before installing the AR-FN1:

*In the case of 2 trays

1. Pull out the paper exit unit from the copier

until it stops.

2. Remove the two screws which are fixing

the paper feed cover. Remove the paper

exit cover.

3. Remove the two transport springs attached

to the paper exitcover.

4. Hang the removed transport springs on the

paper exit unitfront frame (Fig. 1) to keep

there.

5. Return the paper exit cover to the original

position and fixit with two fixing screws.

6. Replace the connection gear at the rear of

the paper exit unitwith the gear packed

together with the unit as shown below.

7. Insert the paper exit unit into the copier.

After completion of the above procedures,

perform installingprocedures according to

the installation manual.

3 2-4 [2]-2-14 Paper exit roller spring removal 14.Delete.

4 3-2 [3]-3 Clutch solenoid

llustration 12: T30RSL T30RSL is changed to T30RCL.

Table No. 12: T30RSL

5 3-4 [3]-5 Motor PWB unit

Table No.1: Main drive motor Error print is corrected to

Main drive motor.

6 4-3 [4]-2-A Table No.(13): Signal name P12CL Signal name iP12CL is changed to T12CL.

7 4-6 [4]-2-E Elevator section

Table No.(2): Name elevator drive unit Corrected to Elevator drive unit.

8 5-1 [5] Disassembly and assembly

Table Item 2: Part name staple unit drive motor Corrected to Staple unit drive motor.

[Fig.1]

Paper exit unit

Fixing screw

Paper exit cover Fixing screw

Transport spring

Connection

gear

AR-FN1N

1/21/1999 – 1 –

No. AR-FN1 AR-FN1N

Page Item Content Change Remark

9 6-1 [6] Adjustment

Table Item 1: Part name jogger F/R Delete "1. Jogger F/R" from the table.

[6]-1 Jogger F/R Delete "1 Jogger F/R."

10 6-7 [6]-11 Vertical transport roller unit

Set value

Set value Part code and price rank of the jig

are added to the set valuetable.

Set value

Nip amount 0.5±0.1

External dimension of

shaft 21.6

Jigs Color jig R0.5

Partcode:OEUKOG0602L//

Price rank: GN

Color jig F0.5

partcode OEUKOG0603L//

Price rank: GN

11 6-7 [6]-12 Paper entry port decurler unit

Nip amount adjustment Part code and price rank are added to the

table of nip amountadjustment.

Nip amount

(Reference)

Externalshaft

dimension

0.5

±0.1 0.8

±0.1 1.2

±0.1 1.6

±0.1

21.8 21.3 20.9 20.5

Inchseries F/R

EX AB series F R

Japan F/R

Jig Partcode:OEUKOG0601L//

Price rank: GN

12 8-2 [8]-2-1 The finisher does not operate. (excluding the

case of jam) Delete "upper transport open/close" in the

description. Refer tothe following.

13 9-5 [9]-4-D Extension I/O: M66500FP (IC3) expansion sig-

nal

Pin No. Signal name Specifications Signalname: STID2 is changed to STID2/.

16 STID2 Signalname: WLCL is changed to T3SLCL.

46 WLCL Tray 3 speed reduction

clutch drive signal

(H: ON)

Specification: "Tray 3 sped change" is changed to

"Tray 3 speed reduction."

48 STSL Staple tray paper

holding solenoid (H: ON) Signalname: STSL is changed to T12CL.

64 T12CL Tray 1/2 speed

reduction clutch drive

signal (L: ON)

Specification: "Staple tray paper holding solenoid

(ON at H)" is changed to "Tray 1/2

speed reduction clutch drive signal

signal (ON at H).

Signalname: T12CL is changed to T30RCL1.

Specification: "Tray 1/2 speed reduction clutch

drive signal (ON at L)" is changed to

"Tray 3 paper exit roller clutch

(ON at L).

Is the

main PWB

DSW1.2.3PGOP

signal O.K. ?

YES

Check connection of

the copier, the harness

connection of the

harness which is

connected to the top/

front/upper transport

open/close switch.

Replace if necessary.

Is the

main PWB

DSW1.2.3PGOP

signal O.K. ?

YES

Check connection of

the copier, the harness

connection of the harness

which is connected to the

top/front switch. Replace if

necessary.

AR-FN1N

– 2 – 1/21/1999

No. AR-FN1 AR-FN1N

Page Item Content Change Remark

14 10-1 [10]-1 Actual wiring diagram

15 10-2 [10]-1 Main PWB 2/2

16 10-3 [10]-2 Main PWB

17 10-5

10-6 [10]-2 Main PWB circuit diagram The following figure is added to Main PWB cir-

cuit diagram D-5 Added.

18 10-8 [10]-2 Main PWB connector signal table D-4 Connector signal table D-4

T3SLCL/ is changed to T3SLCL.

(Refer to the table below.)

2+24V12RD 1+24VIN1RD CN-C

1+24VIN RD

3GND1 GY

5GND2 GY

6+5V BL

CN-A

4PIN

Rear

2+24V12RD 1+24VIN1RD CN-C

1+24VIN RD

3GND1 GY

5GND2 GY

6+5V BL

CN-A

4PIN

4GND1

GND2

GND316

CN-A

CN-B

CN-J

Rear

Added.

3GND2 GY

2STND/ PK

1+5V BL

CN-J

613 +5V5BL 14 T3UP4LB 15 GND23GY CN-J

3GND2 GY

2STND/ PK

1+5V BL

CN-J

613 +5V5BL 14 T3UP4LB 15 GND23GY CN-J

1+24V

PPSL/ 1

1PPSL

Added.

R135 10K

R136 10K

IC02

VCC

TIOCA3/TP8/PB0

TIOCB3/TP9/PB1

TIOCA4/TP10/PB2

TIOCB4/TP11/PB3

TOCXA4/TP12/PB4

TOCXB4/TP13/PB5

VSS

TXD0/P90

TXD1/P91

RXD0/P92

RXD1/P93

D0/P40

D1/P41

D2/P42

D3/P43

VSS

D4/P44

D5/P45

D6/P46

D7/P47

%%oDREQ0%%o/TP14/PB6

%%oADTRG%%o/%%oDREQ1%%o

%%oRESO%%o

%%oIRQ4%%o/SCK0/P94

%%oIRQ5%%o/SCK1/P95

R201 10K

RMA

RMA/

RMB

RMB/

PMA

F-DSRF-DSR

PMA/

F-RXDF-RXD

PMB

PMB/

N.C

F-TXD

N.C

F-DTR

STUMA

F-DTR

STUMA/

STUMB

STUMB/

OFMA

OFMB

STGSL

(YB2SL)

VCCVCC

RESO/

GND

RMA

RMA/

RMB

RMB/

PMA

PMA/

PMB

STUMA

STUMA/

STUMB/

STUMB

PPSL

OFMB

OFMA

PMB/

2-7B

2-7C

2-7B

2-7C

2-7B

2-7C

2-5C

1-4A

2-7A

2-5C

R135 10K

R136 10K

IC02

VCC

TIOCA3/TP8/PB0

TIOCB3/TP9/PB1

TIOCA4/TP10/PB2

TIOCB4/TP11/PB3

TOCXA4/TP12/PB4

TOCXB4/TP13/PB5

VSS

TXD0/P90

TXD1/P91

RXD0/P92

RXD1/P93

D0/P40

D1/P41

D2/P42

D3/P43

VSS

D4/P44

D5/P45

D6/P46

D7/P47

%%oDREQ0%%o/TP14/PB6

%%oADTRG%%o/%%oDREQ1%%o

%%oRESO%%o

%%oIRQ4%%o/SCK0/P94

%%oIRQ5%%o/SCK1/P95

R201 10K

RMA

RMA/

RMB

RMB/

PMA

F-DSRF-DSR

PMA/

F-RXDF-RXD

PMB

PMB/

N.C

F-TXD

N.C

F-DTR

STUMA

F-DTR

STUMA/

STUMB

STUMB/

OFMA

OFMB

STSL

(STSL)

VCCVCC

RESO/

GND

RMA

RMA/

RMB

RMB/

PMA

PMA/

PMB

STUMA

STUMA/

STUMB/

STUMB

PPSL

OFMB

OFMA

PMB/

2-7B

2-7C

2-7B

2-7C

2-7B

2-7C

2-5C

1-4A

2-7A

2-5C

STGSSS+ (YB2SL) is

changed to STSL.

CNH-07

CNH-06

CNH-05

CNH-08

C03

47U/35V

STUMBSTUMB

STUMA/

STUMA

STUMB/

STMA

STMB

1-4B

+5V +24V

CNJ-13 CNH-29

CNJ-15

0.1uF 0.1uF

C75

Added.

PPSL/

T3SLCL/

+24V

CNL (B14B-PHDSS)

SIGNALNO

COM705

+24V PPSL

PPSL/

T3SLCL

T3SLCL/

+24V

CNL (B14B-PHDSS)

SIGNALNO

COM705

+24V PPSL

AR-FN1N

1/21/1999 – 3 –

Printed in Japan.

No part of this publication may be reproduced,

stored in a retrieval system, or transmitted,

in any form or by any means,

electronic, mechanical, photocopying, recording, or otherwise,

without prior written permission of the publisher.

SHARP CORPORATION

Printing & Reprographic Systems Group

Quality & Reliability Control Center

Yamatokoriyama, Nara 639-1186, Japan

1999 January Printed in Japan

AR-FN1N

Otros manuales de Copiador de Sharp

Sharp

Sharp AR-C330 Key operators Manual de usuario

Sharp

Sharp AR-C330 Key operators Manual de usuario

Sharp

Sharp SD-2060 Manual de usuario

Sharp

Sharp AR-156 Manual de usuario

Sharp

Sharp AR-235 Manual de usuario

Sharp

Sharp AR-164 Manual de usuario

Sharp

Sharp AL1215 - B/W Laser - Copier Manual de usuario

Sharp

Sharp AR-150 SERIES Manual de usuario

Sharp

Sharp Z-50 Manual de usuario

Sharp

Sharp AL1215 - B/W Laser - Copier Manual de usuario

Sharp

Sharp AR-507 Manual de usuario

Sharp

Sharp AL-1000 Series Manual de usuario

Sharp

Sharp SF-7320 Manual de usuario

Sharp

Sharp MX-2300N Guide Instrucciones de uso

Sharp

Sharp IMAGER AR-5316 Manual de usuario

Sharp

Sharp AR-D11 Manual de usuario

Sharp

Sharp SF-2540 Manual de usuario

Sharp

Sharp AR-C240P Actualización de firmware

Sharp

Sharp AR-C150 Manual de usuario

Sharp

Sharp AR-C250 Manual de usuario

Sharp

Sharp SF-2314 Manual de usuario

Sharp

Sharp AR-5316E Guía de configuración

Sharp

Sharp MX-2301N Manual de instalación y funcionamiento

Sharp

Sharp AL-1670 - B/W Laser - Copier Manual de usuario

Manuales populares de Copiador de otras marcas

Canon

Canon iR1210 Manual de referencia

Ricoh

Ricoh FW740 Manual de usuario

Minolta

Minolta CF910 Manual de usuario

Ricoh

Ricoh B003 Manual de usuario

Xerox

Xerox EC70 Manual de usuario

Oce

Oce 9800 Manual de usuario

Olivetti

Olivetti d-Copia 1800 Manual de usuario

Minolta

Minolta Di181 Manual de usuario

Canon

Canon iR5000i Manual de usuario

Telecrane

Telecrane F25 Manual de usuario

Xerox

Xerox WorkCentre Pro 40 Manual de usuario

Canon

Canon NP6317 Cómo utilizar

Ricoh

Ricoh Di-C1 Manual de usuario

Mita

Mita MIP-2400 Manual

Muratec

Muratec MFX-C2280 Manual de usuario

Ricoh

Ricoh FT5034C Manual de usuario

Minolta

Minolta EP4000 Manual de usuario

Ricoh

Ricoh V-C3 Guía de instalación