Sharp XE-A212 Guía de instalación

XE-A212 Frequently Asked Questions Page 1 of 21

XEA212Frequently asked questions.

XE-A212 Frequently Asked Questions Page 2 of 21

How do I prepare my XEA212 for set-up?

Take the XEA212 out of its box, remove the packing materials. Place the XEA212 on

a flat stable surface, close to a power outlet. Also insure it will not be exposed to

direct sunlight, and is away from water (taps, sinks, etc).

How do I clear the XEA212 to ready it for programming?

It is very important that you “initialise” the XEA212 correctly once you have

removed it from the box, and are ready to start programming. If you do not

“initialise” the XEA212, it might not work correctly.

1. Insert the MA key into the mode switch and turn it to the REG position.

2. Insert the plug of the power cord into a power outlet.

This must be done without the batteries installed. If you have installed

batteries; be sure to remove them before you start this procedure.

After about 10 seconds the buzzer will then sound three times. If the buzzer

does not sound three times, please try again.

The cash register has now been “initialised”. If there were any data from a previous

programming attempt they would have been cleared. The display should now show:

NO BATTERY.

XE-A212 Frequently Asked Questions Page 3 of 21

How to install the batteries, and why should I do so?

The XEA212 uses 3 x AA size batteries to hold its preset, and sales data in memory

when it is switched off. If you do not install 3 x AA size batteries; the XEA212 will

be cleared of all preset, and sales data when it is turned off.

1. Lift the printer cover up and forward, and detach it. Be careful of the paper

cutter to avoid cutting yourself.

2. Open the battery compartment cover next to the paper roll cradle.

3. Install 3 alkaline AA size batteries. When the batteries are properly installed

the “No Battery” message on the display will disappear.

4. Close the battery compartment cover.

A set of new alkaline batteries once installed will keep the memory for up to one year

without power. Please see the question on how to replace the batteries for details on

when and how to replace the batteries. If the unit is not used for some months, you

might not get any warning when you turn the XEA212 on that the batteries have

failed. In this instance the XEA212 will initialise itself.

XE-A212 Frequently Asked Questions Page 4 of 21

What sort of paper roll do I use, and how do I install it?

The XEA212 uses a thermally sensitised paper roll which is: 57mm wide. Its

maximum diameter should be no more than 80mm.

1. Remove the print cover, be careful not to cut yourself on the paper cutter.

2. Lift up the green print roller release lever to unlock and open the print roller

arm.

3. Set a thermally sensitive paper roll in the paper roll cradle as shown in the

diagram below:

XE-A212 Frequently Asked Questions Page 5 of 21

4. Feed the end of the paper along with the paper position guides as shown in the

diagram below.

5. While holding down the paper, slowly close the print roller arm, and push

down the arm until you hear a click. This means the arm is locked back in

place. The paper will feed automatically

6. Cut off the excess paper using the edge of the inner cover, and replace the

external printer cover. Press the key to make sure the paper end comes out

of the printer cover and clean paper appears.

If the paper end does not come out. Open the printer cover, and pass the paper

end between the paper cutter and the paper guide of the printer cover, and

replace the cover.

7. If you intend to use the print out as a journal: Insert the paper end into the slot

in the spool. Press the key to feed more paper if required.

Wind the paper two or three turns around the spool shaft. Set the spool on the

bearing and press the key to take up any slack in the paper. Replace the

printer cover.

XE-A212 Frequently Asked Questions Page 6 of 21

How do I set the time and date?

1. Set the mode key to the PGM position.

2. Enter the time as a four digit number. Use the 24 hour format. For example

2:30pm would be entered as 1 4 3 0

3. Press the #key

4. Enter the date as an eight digits using the day-month-year format. For example

5. 7th of December 2010 would be entered as 0 7 1 2 2 0 1 0

6. Press the #key

How do I set a 10% GST rate?

1. Set the mode key to the PGM position

2. Enter: ST 9 1 1 0 ST TL

XE-A212 Frequently Asked Questions Page 7 of 21

How do I set a Department as taxable or not taxable?

1. Set the mode key to the PGM position

Department keys are the keys labeled 1 to 6 above the numeric key pad

2. To make a department taxable, enter:

-1--0-0 -8--1-DEPT KEY TL

For example to make department 1 taxable enter:

-1--0-0 -8--1-- 1 -DEPT 1 KEY TL

For example to make department 1 non-taxable enter:

-8--1-- DEPT 1 KEY -TL

XE-A212 Frequently Asked Questions Page 8 of 21

How do I set the letters GST to print on the receipt?

1. Set the mode key to the PGM position

2. Enter: ST 3 _●_8 __G S _T ST TL

You can enter characters with the QWERTY

key sheet overlay.

How do I set the $ symbol to print on receipts?

1. Set the mode key to the PGM position

2. Enter:

ST 8 5 _●_SPACE SPACE SPACE _$_ST TL

Use the QWERY keyboard overlay as shown above. Enter the 3 spaces and the $

symbol.

XE-A212 Frequently Asked Questions Page 9 of 21

How do I give a department a descriptive name?

1. Set the mode key to the PGM position

Department keys are labeled 1 to 6 above the numeric key pad.

Enter: ST -1-_●_DEPT KEY enter characters

You can now enter up to 16 characters with the QWERTY keyboard overlay.

3. Press the ST to confirm your selection.

4. Press the TL key to save your selection.

XE-A212 Frequently Asked Questions Page 10 of 21

How do I program the PLUs? (Price Look Ups)

The XEA212 is set at Master Reset (Factory Default) to have 210 PLUs. These

PLUs are assigned to 3 keyboard levels. PLUs 1 to 70 are on level one. PLUs 71

to 140 are on level two, and PLUs 141 to 210 are on level three. PLUs are used to

“look up”, a description and price for often sold items.

Please follow the steps below to program a PLU

1. Set the mode key to the PGM position

2. Press a PLU key (1 to 70). These are the numbered keys to the right of the

numeric key pad). If the PLU is on level 2, press the L2 key before the PLU

key. If it is on level 3 press the L3 key before the PLU key

3. For example press _1_ to right of the TL key to select PLU 1.

4. Press the _00_key.

5. Type in you PLU’s description, up to 16 characters. Use the QWERTY key

sheet overlay.

6. Press ST to confirm the description.

7. Use the numeric key pad to enter the PLU’s price in cents. For example

$14.00 is entered as 1400

8. Press ST to confirm the price.

Otros manuales para XE-A212

Otros manuales de Caja registradora de Sharp

Sharp

Sharp XE-A101 Manual de usuario

Sharp

Sharp ER-A247 Manual de usuario

Sharp

Sharp ER-A420 Manual de usuario

Sharp

Sharp XE-A107 Manual de lista de piezas

Sharp

Sharp XE-A107 Manual de usuario

Sharp

Sharp XE-A407 Manual de usuario

Sharp

Sharp XE-A307 Manual de usuario

Sharp

Sharp XE-A106 Guía de configuración

Sharp

Sharp XE-A42S Manual de usuario

Sharp

Sharp XE-A177BK Manual de usuario

Sharp

Sharp XE-A203 - Cash Register Thermal Printing Graphic Logo... Manual de usuario

Sharp

Sharp ER-A520 Manual de usuario

Sharp

Sharp XE-A107 Manual rápido

Sharp

Sharp XE-A207W Manual de operación y mantenimiento

Sharp

Sharp ER-4700 Manual de usuario

Sharp

Sharp XE-A402 Manual de usuario

Sharp

Sharp XE-A1BT Manual de usuario

Sharp

Sharp XE-A202 - Electronic Cash Register Manual de usuario

Sharp

Sharp ER-A440 Manual de usuario

Sharp

Sharp XE-A107 Manual de usuario

Sharp

Sharp XE-A107 Manual de usuario

Sharp

Sharp XEA102 - Cash Register Manual de usuario

Sharp

Sharp ER-A610 Manual de usuario

Sharp

Sharp UP-600 Manual de usuario

Manuales populares de Caja registradora de otras marcas

Royal

Royal 480nt Manual de usuario

Olivetti

Olivetti ECR 8200 S Manual de usuario

TEC

TEC TEC FS-3600 Manual de usuario

Integrated System Laboratory

Integrated System Laboratory ISL 4006 Manual de usuario

Sam4s

Sam4s ER-380 Guía de solución de problemas

Samsung

Samsung ER 5215 Manual de usuario

Toast

Toast Toast Manual de usuario

TEC

TEC MA-600-1 series Manual de usuario

QUORION

QUORION CR 1200 Manual de usuario

Olivetti

Olivetti ECR 7700 LD eco Plus Manual de usuario

TEC

TEC TEC MA-1060 Manual de usuario

Casio

Casio PCR-408 Instrucciones de montaje

ELCOM

ELCOM Euro-2100TE Manual de usuario

American Changer

American Changer CLASSIC Series Manual de usuario

Sam4s

Sam4s ER-180 Manual de usuario

Sam4s

Sam4s ER-5100? SERIES Manual de usuario

Casio

Casio PCR-T273 Manual de usuario

Casio

Casio PCR-T2100 Manual de usuario